Sirius Satellite Radio SL906 L 1500 Kurzanleitung

INSTALLATION, USE AND MAINTENANCE INSTRUCTION

SL906 L 1500

SL920 L

TECHNICAL INFORMATION

TYPE: FSLC

COMMERCIAL INFORMATION FOR THE CONSUMER

The symbol on the product or on its packaging indicates that this product may not be

treated as household waste. Instead it shall be handed over to the applicable collec-

tion point for the recycling of electrical and electronic equipment. By ensuring this pro-

duct is disposed of correctly, you will help prevent potential negative consequences for

the environment and human health, which could otherwise be caused by inappropriate

waste handling of this product. For more detailed information about recycling of this pro-

duct, please contact your local city ofce, your household waste disposal service or the

shop where you purchased the product. This appliance is marked according to the Eu-

ropean directive 2012/19/EC on waste electrical and electronic equipment (WEEE).

CONTENTS

Warnings

Uses

Installation

Working

Maintenance

If the rating lable in the cooker-

hood shows the symbol , the

appliance is built in class II°

and it does not need any earth

connection.

If the rating lable in the coo-

ker-hood does not show the

symbol , the appliance is

built in class I° and it needs

the earth connection.

* When performing the electri-

cal connections on the applian-

ce, please make sure that the

current-tap is provided with earth

connection and that voltage va-

lues correspond to those indica-

ted on the label placed inside the

appliance itself.

- Before carrying out any clea-

ning or maintaining operations,

the appliance needs to be remo-

ved from the electric grid. If the

appliance is not provided with a

non-separable exible cable and

plug, or with another device en-

suring omnipolar disconnections

from the grid, with an opening di-

stance between the contacts of

at least 3 mm, then such discon-

necting devices must be sup-

plied within the xed installation.

If the xed appliance is endowed

with a supply cord and a plug,

the appliance has to be put in a

place where the plug can be rea-

ched easily.

WARNINGS

- The bottom of the cooker

hood must be at least at 65 cm

of distance from the hob. It is

recommended to install the co-

oker hood in a central position

above the hob, in order to en-

sure the product’s best perfor-

mance.

* The air sucked can’t be con-

veyed through or into a duct

used to let out fumes from ap-

pliances fed by energy other

than electric power (eg. centra-

lized heating, radiators, water-

heaters, etc.).

- Attention: remove any possi-

ble pvc lm from the stainless

steel.

* To evacuate the air outlet, ple-

ase comply with the pertaining

rules given by competent au-

thorities.

* Provide the room with an ade-

quate aeration when a cooker

hood and appliances fed by ener-

gy other than electric power (gas-,

oil-, or coal- stoves, etc.) are used

simultaneously. The cooker hood,

when evacuating the sucked air,

could generate a negative pres-

sure in the room- which can’t ex-

ceed the limit of 0.04 mbar, in or-

der to avoid the suck of exhausts

deriving from the heat-source.

Therefore the room should be

provided with air-intakes to allow

a costant ow of fresh air.

USES

The appliance is already arranged both for lte-

ring and for suction performances.

- In its ltering version (Pic. 1), the air and fu-

mes conveyed by the appliance are depured both

by a grease lter and by an active coal lter, and

put again into circulation through the hole made

on the top of the cabinet.

- In its sucking version (Pic. 2), fumes are di-

rectly conveyed outside, through an evacuation

duct connected with the superior part of the wall

or the ceiling. Both coal lter and air deector are

not necessary in this case.

- The use of materials which

can burst into ames should

be avoided in close proximity

of the appliance. When frying,

please pay particular attention

to re risk due to oil grease.

Being highly inammable, fri-

ed oil is especially dangerous.

Do not use uncovered electric

grills. In order to avoid pos-

sible re risk, all instructions

for grease-lter cleaning and

for removing eventual grease

deposits should be strictly fol-

lowed.

To ensure good performances

of the product is recommen-

ded to install the hood central-

ly with respect to the cook top

(Fig. 12).

INSTALLATION

Before installing the appliance, make sure that

none of the parts is damaged in any way.

In case of damaged parts, contact your retailer

and do not proceed with installation.

Read all of the following instructions with care be-

fore installing the appliance.

- Before installing the appliance, remove the me-

tal grease lter. This lter can be removed by pu-

shing the handles towards the back side of the

cooker hood and turning it downwards to unfa-

sten it from its slot. (Pic. 3).

To install the appliance please respect the fol-

lowing instructions.

The appliance must be installed by competent

authorities. In order not to damage the electronic

parts of the appliance please do not use additio-

nal screws.

Essential precautions to respect before installing

the appliance are the following:

- Prepare the power supply.

- Prepare a hole for the exhaust of the air both in

the ltering and in the exhausting version.

- Use an exhausting pipe whose maximum length

does not exceed 5 meters.

- Do not use screws to x the outlet pipe to the

cooker hood.

- Limit the no. of elbows in the piping, since each

elbow reduces the aspiration efciency of 1 linear

meter. (Ex.: if you use no. 2 x90 ° elbows, the

length of piping must not exceed 3 meters)

- Avoid abrupt direction changes.

- Use a 200 mm or 300 mm constant diameter

pipe for the whole length.

- Use piping approved by standards in force.

- In the units equipped with 2 motors please use

a 200mm constant diameter pipe for the whole

length.

In the units with 3 motors please use a 300mm

constant diameter pipe for the whole lenght.

Please be sure to have made a cut-out on the

bottom of the cabinet which is suitable to hold the

appliance in position (Fig. 4).

SL906L 1500 1480x364mm

SL920L 856 821X505mm

SL920L 1200 1165X505mm

SL920L 1500 1470X505mm

At this point, insert the range hood inside the

kitchen cabinet until the xed springs will be ho-

oked into.

When the hood will be positioned into the cabinet,

it’s important to x the appliance according to the

following instructions.

Unscrew by 180° the horizontal screws as shown

in g. 5, during this operation it is necessary to

support the hood with your hand (g. 5).

Screw the vertical screws so that the hood is

adherent to the cabinet.

Repeat this operation for all four screws.

If it is necessary, it’s possible to put other screws

along the front or rear of the product as shown in

picture 7.

Warning: according to the model you have pur-

chased, please read the “maintenance” chapter

to check whether the light has to be removed

when installing the screws.

Make the electrical connection and connect the

air outlet pipe.

Warning!

Before connecting the exible exhausting pipe to

the motor, make sure that the stop valve, which is

on the air outlet of the motor, can swing.

Exhausting version

Connect the ange to the exhausting hole with an

appropriate pipe. Connect the appliance with the

electrical mains through the supply cord.

Filtering version

Connect the ange with a pipe suitable to con-

vey the air to the top of the cabinet. Connect the

appliance with the electrical mains through the

supply cord.

WORKING

Push button (g. 8)

A: Light switch on/off

B: Motor switch on speed 1/off

C: Motor switch on speed 2

D: Motor switch on speed 3

E: Motor switch on speed 4

F: 10-minutes timer

Remote control instruction (If it is included)

RC001

RADIO CONTROL

Radio control used for the remote operation of

ducted cooker hoods.

TECHNICAL DATA

- Alkaline battery powered: 12V mod. 27A

- Operating frequency: 433.92 Mhz

- Combinations: 32.768

- Max. consumption: 25 mA

- Operating temperature: -20 ÷ + 55 °C

- Dimensions: 130x45x15 mm.

OPERATING DESCRIPTION

The transmitter is equipped with 5 buttons for co-

oker hood management, as specied below:

: Light ON/OFF command.

: Motor ON (speed level 1) / OFF command.

: Reduce speed.

: Increase speed.

: 10-minute timer.

INITIAL OPERATING CONDITION

The manufacturer supplies the radio control unit

ready to be used with codes preset in the Factory

OPERATION MODE

Standard conguration:

Standard conguration requires all “cooker hoods

– radio control - system” to be provided with the

same transmission code. In the event two cooker

hoods – radio control system are installed in the

same room or nearby, each system may affect

the operation of the another. Therefore, the code

of one radio control system must be changed.

Generating a new transmission code:

The radio control system is provided with preset

codes. Should new codes be required, proceed

as follows: Press simultaneously buttons:

for two seconds. When Leds light on, press but-

tons:

(within 5 seconds). Leds ashing 3 times indicate

the procedure is completed.

WARNING! This operation deletes permanen-

tly the preset codes.

Learning the new transmission code:

Once the transmission code is changed in the ra-

dio control unit, the electronic central unit of the

cooker hood must be made to set the new code

in the fol- lowing way:

Press the main power-off button of the hood and

then restore power to the electronic control unit.

Within the next 15 seconds, press the Liight But-

ton to synchronise the central unit with the

code.

Reset of the Factory conguration:

To restore the Factory conguration, follow the

procedure described below: press simultaneou-

sly buttons:

for 2 seconds. When Leds light on, press buttons:

(within 5 seconds). Leds ashing 6 times indicate

the procedure is completed.

WARNING! This operation deletes permanen-

tly the preset codes.

Emergency button:

In the event that the radio control does not work,

use the emergency button to switch the appliance

off. After any necessary repairs have been perfor-

med, reset the emergency button.

WARNING

The battery should be replaced every year to

guarantee the optimal range of the transmitter.

To replace the exhausted battery, take the pla-

stic lid off, remove the battery and replace it

with a new one, observing the correct battery

polarities.

Used batteries should be discarded in special

collection bins.

The below product:

RC001 Radiio Controll

complies with the specications set out in the

R&TTE Directive 99/5/EC.

WARNING

Any adjustments or modications which have

not been expressly approved by the holder of

the legal conformity certicate may invalidate

the user’s rights relating to the operation of

the device.

The products are endowed with an electronic de-

vice which allows the automatic switching off after

4 hours working from the last operation.

- An accurate maintenance guarantees good fun-

ctioning and long-lasting performance.

- Particular care is due to the grease lter. It can

be removed by pushing its special handle toward

the back-side of the cooker hood and turning the

lter downwards so to unfasten it from its slot

(Pic. 3).

To insert the lter just perform the opposite ope-

ration.

After 30 hours working, the push button control

panel will signal the saturation of the grease lter

by lighting all the buttons. Press the timer button

to reset .

The grease lter needs cleaning by regular hand-

washing or in dishwashers every two months at

least or depending on its use.

- How to remove the oil tank.

First, remove the grease lter, Than place your

hand under the oil tank and unfasten the handles

(Pic. 9) Eventually remove the oil tank, paying at-

tention to the leaking oil.

- To clean the appliance itself tepid water and

neutral detergent are recommended, while abra-

sive products should be avoided. For steel ap-

pliances specialized detergents are recommen-

ded (please follow the instructions indicated on

the product itself to obtain the desired results).

* If the supply cord is damaged, it must be re-

placed by the manufacturer or its sevice agent

or a similarly qualied person in order to avoid

a hazard.

Replacing the lamps

Before replacing the lamp switch off the applian-

ce then by using appropriate tools remove the

lamp from its slot (Pic. 10).

Take out the led bar from its connector and repla-

ce with one having similar characteristics.

To nd the correct led bar please check on the

replacement part list.

To remove the appliance from the cabinet is ne-

cessary to remove the installation bracket by the

eight nuts, as shown in the picture 11.

MAINTENANCE

WIRING DIAGRAM SL906L 1500

Dieses Handbuch passt für folgende Modelle

Andere Sirius Satellite Radio Dunstabzugshaube Handbücher

Sirius Satellite Radio

Sirius Satellite Radio SL920 FRESCO Series Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SM923L520 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SLT972 EM WIFI Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SLT955 Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio ALFRESCO SLEM80 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SLEM83 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio Valentina SLT977EMEL Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SLTC 111 Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SU900 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SUT950 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio FSED Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio UP right Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio S-DDH3 Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio S-DDH1.1 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SILT18 Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio Alfresco SIL25FRESCO1200 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SM923 520 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SUM Series Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SLTC EM 107 G900 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SLT972 Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio S-DD2-L EMIC 880 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio Valentina SLT958EM Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SU900 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio Stone SU-DD2-L Kurzanleitung

Beliebte Dunstabzugshaube Handbücher anderer Marken

emmeti

emmeti RECUPA MED A-140 Leitfaden

Nibe

Nibe F135 Bedienungsanleitung

Zephyr

Zephyr Spruce AK9834BS Installationsanleitung

Kuppersberg

Kuppersberg INTRO 60 Montage- und Wartungsanleitung

Hisense

Hisense MH6INBG Bedienungsanleitung

Miele

Miele DA 1255 Bedienungsanleitung

Broan

Broan 46000 Bedienungsanleitung

GE Profile PV977 Originalbetriebsanleitung

FALMEC

FALMEC FFRIA24W5FS Bedienungsanleitung

Whirlpool

Whirlpool RH2600XL-1 SERIES Bedienungsanleitung

ETNA

ETNA AV360RVS Bedienungsanleitung

JUNO

JUNO JDF603E6 Bedienungsanleitung

Miele

Miele DA 6708 D Bedienungsanleitung

Tricity Bendix

Tricity Bendix LE 150 Handbuch

AEG

AEG X68163BV1 Bedienungsanleitung

AEG

AEG 125 D Bedienungsanleitung

Smeg

Smeg KSEV97X Bedienungsanleitung

Nibe

Nibe S Series Benutzerhandbuch