Sirius Satellite Radio SLTC EM 107 G900 Bedienungsanleitung

CANOPY RANGEHOOD

OFFBOARD INSTALLATION INSTRUCTIONS

Congratulations on your purchase!

Thank you for choosing a Sirius product.

www.siriusbrand.com

SLTC EM 107 G900 EAN# 9351116001766

SLEM 107 S900 EAN# 9351116001759

SLEM 107 S1200 EAN# 9351116001773

SLTC EM 92 G900 EAN# 9351116000721

SLTC EM 92 G900 WH EAN# 9351116000752

SLEM 2 900 EAN# 9351116000639

SLTC EM 97 900 EAN# 9351116001605

BEFORE YOU INSTALL - DUCTING INFORMATION 4

CANOPY RANGEHOOD INSTALLATION 6

USING THE RANGEHOOD 8

MAINTENANCE 9

SLEM 107 S900 / SLEM 107 S1200 WIRING DIAGRAM 10

SLTCEM 107 G900 WIRING DIAGRAM 11

SLTCEM 92 G900/WH WIRING DIAGRAM 12

SLEM 2 900 WIRING DIAGRAM 13

BRACKET 14

WARRANTY INFORMATION 15

TABLE OF CONTENTS

The symbol on the product or on its packaging indicates that this product

may not be treated as house-hold waste. Instead it shall be handed

over to the applicable collection point for the recycling of electrical and

electronic equipment. By ensuring this product is disposed of correctly,

you will help prevent potential negative consequences for the environment

and human health, which could otherwise be caused by inappropriate

waste handling of this product. For more detailed information about

recycling of this product, please contact your local city office, your

household waste disposal service or the shop where you purchased the

product. This appliance is marked according to the European directive

2002/96/EC on waste electrical and electronic equipment (WEEE).

Sirius warranty covers only Sirius product. If you choose to install a non-Sirius branded accessory

such as flexible ducting, Sirius will only warrant the rangehood and motor. If installation is found to be

the cause of failure or issue then charges will apply for service and parts.

Flexible ducting is not permitted under any circumstances. Flexible ducting has been found to

increase noise levels, increase vibration and reduce airflow. Sirius Semi-rigid or solid ducting can be

used in lieu. There is a range available to suit any application.

Ducting available at www.siriusbrand.com

6 Year Warranty when Sirius Ducting is used. Full replacement warranty on parts and labour.

See website for terms & conditions.

A reduction in the duct diameter from stated ducting size will void warranty.

If you are in doubt about the ducting, please contact Sirius on 1300 762 219 prior to installation

WARNING

The appliance must be installed and

connected to the power supply only by a

qualified technician.

• There should be adequate ventilation of the room when the rangehood is used at the same time as

appliances burning gas or other fuels (not applicable to appliances that only discharge the air back into the

room)

• The details concerning the method and frequency of cleaning

• There is a fire risk if cleaning is not carried out in accordance with the instructions;

• Do not flambé under the range hood;

• CAUTION: Accessible parts may become hot when used with cooking appliances.

BEFORE YOU INSTALL - DUCTING INFORMATION

Min. 600mm - Max. 700mm for electric cooktops.

Min. 650mm - Max. 750mm gas cooktops.

If the rangehood is positioned above the max height

recommended, warranty may be compromised

as performance of the rangehood will be affected.

Measurement is taken from the top of the trivets to

the underside of the hood. (Fig.1)

• The air being drawn can’t be conveyed through

or into a duct used to let out fumes from

appliances fed by energy other than electric

power (eg. centralized heating, radiators, water

heaters, etc.).

• Attention: remove any possible PVC film from the

stainless steel, including the filters.

• To externally vent, please comply with the

pertaining rules given by competent authorities.

• Provide the room with an adequate ventilation

when a rangehood and appliances fed by energy

other than electric power (gas, oil, or coal stoves,

etc.) are used simultaneously. The rangehood,

when evacuating the air, could generate a

negative pressure in the room which can’t exceed

the limit of 0.04 mbar, in order to avoid the

suck of exhausts deriving from the heat source.

Therefore the room should be provided with air

intakes to allow a constant flow of fresh air.

If the rating label in the rangehood shows the symbol

, the appliance is built in class II° and it does not

need any earth connection.

If the rating label in the rangehood does not show

the symbol , the appliance is built in class I° and it

needs the earth connection.

When performing the electrical connections on the

appliance, please make sure that the current-tap

is provided with earth connection and that voltage

values correspond to those indicated on the label

placed inside the appliance itself.

Before carrying out any cleaning or maintaining

operations, the appliance needs to be switched off.

If the appliance is not provided with a non-separable

flexible cable and plug, or with another device

When ducting rangehood, options are as follows:

• NOTE: For SEM 1 & SEM 8 only: From motor

to exit point, additional lengths of duct will be

required from the rangehood to the SEM 1 or

SEM 8 motor.

Roof vent - EASYROOF 150T/M

EASYROOF 200T/M

*Kit includes roof flashing

Download installation guide

Eave vent - EASYEAVE 150/200

Download installation guide

Wall vent - EASYWALL 150/200

Download installation guide

SEM 1, 2, 7, 8 MOTOR

Download installation guide

SEM 5 MOTOR

Download installation guide

ensuring omnipolar disconnections from the grid,

with an opening distance between the contacts of at

least 3mm, then such disconnecting devices must be

supplied within the fixed installation.

If the fixed appliance is endowed with a supply cord

and a plug, the appliance has to be put in a place

where the plug can be reached easily.

The use of materials which can burst into flames

should be avoided in close proximity of the appliance.

When frying, please pay particular attention to fire

risk due to oil grease. Being highly flammable, fried

oil is especially dangerous. Do not use uncovered

electric grills. In order to avoid possible fire risk, all

instructions for grease-filter cleaning and for removing

eventual grease deposits should be strictly followed.

WARNING

600 - 700mm (electric)

650 - 750mm (gas)

600 - 700mm (electric)

650 - 750mm (gas)

(Fig. 1)

SIDE VIEW FRONT VIEW

MOTOR INSTALLATION GUIDES

WARNING: Failure to install the screws or fixing

device in accordance with these instructions

may result in electrical hazards.

Rangehood and SEM motor cannot be installed

back-to-back. There must be a minimum of

2 metres between rangehood and motor for

noise reduction reasons.

NOTE

1. The rangehood is quite heavy, so two people

will be needed for installation.

2. Before connecting any ducting to the motor,

make sure the non-return valves - which are on

the air outlet of the motor - can swing open.

3. Using the supplied bracket template (pg. 7), mark

the location of the holes that need to be drilled

in the wall, being careful to make sure that the

wall behind is clear of electrical wiring, plumbing,

pipes etc. Note: Be sure to set the height of the

rangehood between the minimum and maximum

height requirements as per diagram Fig. 1( Pg. 3).

This can be done by measuring from the lowest

point of the rangehood to the horizontal support

bar. (Fig. 4)

NOTE: Model measurements will vary.

Please check specific model specs.

4. Using an 8mm drill bit, pre-drill the holes that

will hold the bracket to the wall. (Using bracket

template)

5. Insert the supplied plastic dowels to the pre-

drilled holes and fix bracket to the wall with the

supplied screws. (Note: Please use a spirit level to

make sure the bracket is perfectly level.)

6. Once the bracket is secure, using two people,

lift the hood and drop the horizontal support bar

onto the fixed bracket (Fig. 5).

(Note: There are additional holes on the inside of

the hood to secure the rangehood flush to the wall

and completely stable. (Hole locations will vary per

model.)

CANOPY RANGEHOOD

INSTALLATION - OFFBOARD MOTOR

Before installing the appliance, make sure that

none of the parts are damaged in any way. In

case of damaged parts, contact your retailer

and do not proceed with installation. Read all

of the following instructions with care before

installing the appliance.

• Use ducting within the min/max specifications

• Limit the number of ducting bends.

• Do not make any changes in ducting diameter

(recommended constant diameter: Ø 150 mm /

Ø 200 mm or equal surface area).

Before installing the appliance - in order not to

damage the appliance itself - the metal grease filter

should be removed. These filters could be removed

by pushing the handles towards the back side of the

rangehood and pulling it downwards to unfasten it

from its slot. (Fig.3).

To install the appliance please follow these

instructions:

• The appliance must be installed by qualified

technicians, or where possible use a Sirius

recommended installer. See siriusbrand.com. In

order to avoid damage to the electronic parts

of the appliance, please do not use additional

screws.

1. Prepare the power supply - 240 volts.

2. Prepare a hole for the exhaust - 160mm diameter

for SEM 1/2/5 & 210mm for for SEM 7/8 motor

versions.

• Maximum length of ducting should not exceed

7 metres to motor. Minimum length of 2 metres

between hood and motor.

• (SEM 1 or SEM 8) Additional 5 metres from motor

to atmosphere.

• Do not use screws to fix the ducting to the

rangehoods as they will prevent the movement of

non-return valves.

• SEM motor

• Limit the number of elbows in the ducting, since

each elbow reduces the duct efficiency by 1

metre. (i.e. if you use two 90° elbows, the length

of ducting must not exceed 5 metres.)

• Avoid abrupt direction changes.

• Use 150mm constant diameter ducting for the

whole length for the SEM 1/2/5 motors, 200mm

ducting for the SEM 7/8 motor model.

• The use of Sirius ducting will increase the

warranty of the unit to 6 years.

NOTE

CAUTION

WARNING

(Fig. 5)

(Fig. 4)

7. Connect your Sirius ducting (see www.

siriusbrand.com for approved ducting) to the

outlet collar on the rangehood and secure in

place with a ring clamp if you are using semi rigid

ducting. If you are using solid/rigid ducting and

external duct connector is required. (Note: do not

fix the ducting in place with screws as they will

prevent the movement of the non-return valves).

Complete all of the duct work to the motor

location before fixing the flue covers in place to

ensure the ducting has not come free. (See www.

siriusbrand.com for motor installation guides.)

8. Insert the upper flue cover into the cover into the

lower flue cover and mount into the channel on

the top of the rangehood. There are two spring

loaded clips that need to be on the inside of the

lower flue cover to secure in place. (Fig 6.)

9. Telescope the upper flue cover to the ceiling and

mark with a pencil the outer line of the cover, this

will give you the exact location of where the top

fixing bracket needs to be fitter to the ceiling.

10. Fix the top fixing bracket into place using the

supplied 30mm screws (Fig.7) and telescope

the upper flue cover over the bracket and secure

in place with the very small 10mm supplied

screws. (Fig 8.)

(Fig. 6)

(Fig. 7)

30mm

(Fig. 8)

NOTE

Please do not fix shroud permanently.

Must be removable for servicing purposes.

10mm

Manual control buttons:

SLTC 107 S900, SLEM 107 S1200, SLEM 2 900

A: Light switch on/off

B: Motor switch on speed 1/off - (low/simmer)

C: Motor switch on speed 2 - (general cooking)

D: Motor switch on speed 3 - (high power)

E: Motor switch on speed 4 - (booster)

F: 10 minute shut-off timer

Electronic touch control

SLTC EM 107 G900, SLTC EM 92 G900,

SLTC EM 92 G900 WH, SLTC EM 97 900

A: Light switch on/off

B: Motor speed decrease / motor off

C: Motor speed indicator

D: Motor speed increase

E: 10 minute shut-off timer

USING THE RANGEHOOD

A B C D E

• Accurate maintenance guarantees good

functioning and long-lasting performance.

• Particular care is due to the grease filter panel.

• It can be removed by pushing its handle toward

the back side of the rangehood and pulling the

filter downwards so to unfasten it from its slot

(Fig.2).

To insert the filter just perform the opposite

operation.

• After 30 hours of operation, the buttons on the

control panel will flash, signaling the filters are due

for cleaning. Press the timer button to reset.

The grease filter needs cleaning by regular

handwashing or in dishwashers every two

months at least, depending on its use.

Filters may require cleaning sooner if

frequent heavy frying is done.

• To clean the appliance itself, water and detergent

are recommended, while abrasive products

should be avoided. For steel appliances

specialized detergents are recommended (please

follow the instructions indicated on the product

itself to obtain the desired results).

If the supply cord is damaged, it must be

replaced by the manufacturer or its service

agent or a similarly qualified person in order to

avoid a hazard.

MAINTENANCE

WARNING

SLEM 107 S900 / SLEM 107 S1200

WIRING DIAGRAM

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Sirius Satellite Radio Dunstabzugshaube Handbücher

Sirius Satellite Radio

Sirius Satellite Radio S-DDH3 Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SL920 FRESCO Series Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SIU3 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio STL969 Bedienungs- und Wartungshandbuch

Sirius Satellite Radio

Sirius Satellite Radio SLT955 Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SLTC EM 97 900 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SM927 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio Downdraft S-DD18 Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SLTC919 520 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SLTC 111 Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SM923 52 Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SLT955 Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SU906 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio S-DDH1 Benutzerhandbuch

Sirius Satellite Radio

Sirius Satellite Radio SUT950 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio Valentina SLT958EM Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SILT-26 Series Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio ALFRESCO SL83 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio Stone SU-DD2-L Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SIU3 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio Valentina Series Bedienungs- und Wartungshandbuch

Sirius Satellite Radio

Sirius Satellite Radio SIU3 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio S-DD2-L EMIC 880 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio Alfresco SIL25FRESCO1200 Bedienungsanleitung

Beliebte Dunstabzugshaube Handbücher anderer Marken

emmeti

emmeti RECUPA MED A-140 Leitfaden

Nibe

Nibe F135 Bedienungsanleitung

Zephyr

Zephyr Spruce AK9834BS Installationsanleitung

Kuppersberg

Kuppersberg INTRO 60 Montage- und Wartungsanleitung

Hisense

Hisense MH6INBG Bedienungsanleitung

Miele

Miele DA 1255 Bedienungsanleitung

Broan

Broan 46000 Bedienungsanleitung

GE Profile PV977 Originalbetriebsanleitung

FALMEC

FALMEC FFRIA24W5FS Bedienungsanleitung

Whirlpool

Whirlpool RH2600XL-1 SERIES Bedienungsanleitung

ETNA

ETNA AV360RVS Bedienungsanleitung

JUNO

JUNO JDF603E6 Bedienungsanleitung

Miele

Miele DA 6708 D Bedienungsanleitung

Tricity Bendix

Tricity Bendix LE 150 Handbuch

AEG

AEG X68163BV1 Bedienungsanleitung

AEG

AEG 125 D Bedienungsanleitung

Smeg

Smeg KSEV97X Bedienungsanleitung

Nibe

Nibe S Series Benutzerhandbuch