Sirius Satellite Radio SUF1 Handbuch

INSTALLATION

INSTRUCTIONS

CARE AND USE MANUAL FOR:

UNDER CABINET RANGE HOODS

Models covered by this instructions:

SUF1

*** BEFORE INSTALLATION ***

ENSURE THERE IS NO VISIBLE OR HIDDEN DAMAGE SUSTAINED

DURING SHIPPING

*** SHIPPING DAMAGE ***

MUST BE REPORTED WITHIN 5 DAYS OF RECEIPT

WARNING

Thank you for purchasing a Sirius Range Hood.

Please read all the instructions in this manual before

installing the appliance.

Save these instructions for future reference.

Only use this appliance as an exhaust ventilation system for the removal of

cooking vapors. DO NOT use to expel ammable substances or any other

materials or vapors.

The installation procedures in this manual are intended for qualied instal-

lers, service technicians or persons with similar qualied background.

DO NOT attempt to install this appliance yourself.

Ensure that electrical power is turned o at source before commencing in-

stallation. All electrical wiring must be properly installed, insulated and

grounded and conform to all applicable codes and standards.

Make sure all existing duct work is clean of grease build up, or duct work

should be replaced, if necessary, to avoid the possibility of a grease re.

Check all joints on ductwork to ensure proper connection and all joints

should be properly taped. Be careful when cutting through ceilings or walls

not to damage any hidden pipes or electrical wiring. Ensure your kitchen has

sucient air return vents to replace the exhausted air.

Fan ducts should always be vented to the outside of your home and never

into spaces within walls, ceilings, lofts or attics. Only use rigid, smooth steel

for ducting. The exhaust point of the blower requires a 6” round connec-

tion.

TABLE OF CONTENTS

BEFORE YOU BEGIN 1

DUCTING 1

External Venting Requirements 1

Duct Run Calculation 1

ELECTRICAL 1

Electrical Supply 1

INSTALLATION 1

Connecting Electricity and Ducting 1

Re-Circulating Requirements 1

OPERATING PROCEDURES 1

General Advice 1

Functions 1

MAINTENANCE 1

Cleaning the Filter 1

Cleaning the Hood 1

Light Bulb Replacement 1

WARRANTY 1

BEFORE YOU BEGIN: It is advisable to test

run the range hood before installation.

BEFORE STARTING – please read this en-

tire document and ensure you are fully

conversant with the require-ments and

limitations. These units weigh approxi-

mately 125lbs and therefore require a

minimum of two people to install.

BEFORE YOU BEGIN

The manufacturer declines all responsi-

bility in the event of failure to observe the

instructions given here for installation,

maintenance and suitable operation of

the product. The manufacturer further

declines all responsibility for injury due

to negligence and the warranty of the

unit automatically expires due to impro-

per maintenance and/or installation.

Always, wherever reduce the number of

transitions and turns with as few sharp

angles as possible.

DUCTING

(Not applicable if the range hood is used

in re-circuling model).

WARNING: Do not vent this appliance

into any other ductwork, spaces between

walls, ceilings, attics, garages or any

other conned space.

External Venting Requirements.

When planning new ductwork, always

look for the most direct route to the ou-

tside. Venting can be done through the

roof or directly through the back outside

wall. (See Figure 1).

Only use rigid type metal ducting (plastic

ducting is generally not permit-ted by

code). Flexible ducting could restrict air-

ow by up to 50%. Always fasten connec-

tions with sheet metal screws and tape all

joints with certied Silver Tape or Duct

Tape.

Do not use screws to fasten ductwork

to the hood, only use tape as the screws

will stop the dampers from opening and

your hood will not work. This hood re-

quires a 6” round duct outlet. You can in-

crease the duct size of the duct run but

never decrease it. Use the shortest and

most direct route possible.

Two staggered 45 degree angles are bet-

ter than one 90 degree. Make these tur-

ns as far away from the motor exhaust

as possible, with as much space between

each bend.

g. 1

Duct Run Calculation

The maximum duct run before eecting

the performance of the hood is 100’. Cal-

culate your duct run by measuring linear

feet and adding the elbows, transitions

and caps based on the table alongside.

Maximum Run

6” or 3 1/4 x 10” duct 100 FT

Deduct

Each 90 elbow used 15FT

Each 45 elbow used 9FT

Each 6” or 3 1/4 x 10” duct

Transition used 1FT

Each 3’1/4 x 10” to 6”

Transition used 5FT

Side Wall with damper 30FT

Roof Cap 30FT

Electrical Supply.

This range hood requires a 120V, 60Hz

supply and draws a maximum of 3 amps.

The electrical supply to the range hood

should be at least 17” from the underside

of the installed range hood.

For a typical installation, where the under-

side of the range hood will be 30” above

the counter top and the counter top is 36”

above the oor level, the electrical supply

should be 76”” above oor level and no

further than 3” to the right (as you face

the wall) of the central axis of the range

hood.

ELECTRICAL

WARNING: All electrical work must be

performed by a qualied electrician.

Please ensure that the appropriate electri-

cal codes or prevailing local building co-

des and ordinances are adhered to.

Ensure that the electricity supply is di-

sconnected at source. Do not use an ex-

tension cord or adapter plug with this

appliance.

This appliance must be grounded. Con-

nect to a properly grounded branch

circuit, protected by a 15 amp circuit

breaker.

The ducting connection to the hood must

be in line with the central vertical axis of

the range hood 1” away from the back

wall on which the hood is to be mounted.

Range hoods may interrupt the proper

ow of combustion gases from repla-

ces, gas furnaces and gas water heaters.

To minimize the risk of drawing these

lethal gases back into the home, please

follow the heating equipment manufac-

turers safety standards and guidelines

carefully.

Refer to NFPA and ASHRAE for additional

information.

INSTALLATION

Before installing the appliance, in order

not to damage the appliance itself, the

metal grease lter should be removed by

pushing the special lter handle toward

the back side of the cooker hood and

turning it downwards so to unfasten it

from its slot (refer to gure 2).

g. 4

nessun mezzo e per nessuno scopo, senza autorizzazione della proprieta'.

Il presente disegno, o parte di esso non puo' essere riprodotto in nessuna forma, con

SPESSORE:

Disegnato da:

MATERIALE:

Descrizione:

n° disegno:

venerdì 16 gennaio 2009

Data creazione:

RAGGIO PIEGA

g. 2

Make a cut-out on the bottom of the ca-

binet to hold the appliance by us-ing the

drilling jig provided. This opening must

be 9.8” x 10.2” and at a distance of 1”

from the front edge of the cabinet (refer

to gure 3).

The hoods can be installed with the air

outlet venting upwards or backwards.

In upwards venting applications make a

round cut-out on the upper part of the

cabinet measuring 6’’Ø as per Picture 3.

Center of the hood

10.2"

9.8"

nessun mezzo e per nessuno scopo, senza autorizzazione della proprieta'.

Il presente disegno, o parte di esso non puo' essere riprodotto in nessuna forma, con

SPESSORE:

Disegnato da:

MATERIALE:

Descrizione:

n° disegno:

lunedì 19 gennaio 2009

Data creazione:

RAGGIO PIEGA

Center of the hood

10.2"

9.8"

nessun mezzo e per nessuno scopo, senza autorizzazione della proprieta'.

Il presente disegno, o parte di esso non puo' essere riprodotto in nessuna forma, con

SPESSORE:

Disegnato da:

MATERIALE:

Descrizione:

n° disegno:

lunedì 19 gennaio 2009

Data creazione:

RAGGIO PIEGA

g. 3

In backwards venting applications turn

the motor assembly box as shown in

picture 4 by unscrewing the screws “A”

and turning the motor assembly box ha-

ving the air outlet venting backwards.

nessun mezzo e per nessuno scopo, senza autorizzazione della proprieta'.

Il presente disegno, o parte di esso non puo' essere riprodotto in nessuna forma, con

SPESSORE:

Disegnato da:

MATERIALE:

Descrizione:

n° disegno:

lunedì 19 gennaio 2009

Data creazione:

RAGGIO PIEGA

nessun mezzo e per nessuno scopo, senza autorizzazione della proprieta'.

Il presente disegno, o parte di esso non puo' essere riprodotto in nessuna forma, con

SPESSORE:

Disegnato da:

MATERIALE:

Descrizione:

n° disegno:

lunedì 19 gennaio 2009

Data creazione:

RAGGIO PIEGA

Fix it with the screws previously remo-

ved. Make a round cut-out on the upper

part of the cabinet measuring 6’’Ø as per

Figure 5.

Connecting Electricity and Ducting.

Please refer to the Electrical Supply sec-

tion on page 2 for the required location

of the electrical supply.

CAUTION: Make sure the power is turned

o at source. Make electrical connections

(refer to Figure 7).

Ensure that the plastic aps at the exhaust

outlet for the fan move freely and have

not become jammed or stuck.

nessun mezzo e per nessuno scopo, senza autorizzazione della proprieta'.

Il presente disegno, o parte di esso non puo' essere riprodotto in nessuna forma, con

SPESSORE:

Disegnato da:

MATERIALE:

Descrizione:

n° disegno:

lunedì 19 gennaio 2009

Data creazione:

RAGGIO PIEGA

nessun mezzo e per nessuno scopo, senza autorizzazione della proprieta'.

Il presente disegno, o parte di esso non puo' essere riprodotto in nessuna forma, con

SPESSORE:

Disegnato da:

MATERIALE:

Descrizione:

n° disegno:

lunedì 19 gennaio 2009

Data creazione:

RAGGIO PIEGA

g. 5

Insert the built-in unit in the hole made

in the cabinet until the stop click of the

side-springs is heard and the hood is

temporary held in position.

To install the appliance adjust the posi-

tion of the stop side-springs using the

appropriate screws, according to the thi-

ckness of the board. The base of the ca-

binet must be from 0.4” to 1” thick (refer

to gure 6).

DETTAGLIO A

SCALA 1 : 10

DETTAGLIO B

SCALA 1 : 10

nessun mezzo e per nessuno scopo, senza autorizzazione della proprieta'.

Il presente disegno, o parte di esso non puo' essere riprodotto in nessuna forma, con

SPESSORE:

Disegnato da:

MATERIALE:

Descrizione:

n° disegno:

lunedì 19 gennaio 2009

Data creazione:

RAGGIO PIEGA

DETTAGLIO A

SCALA 1 : 10

DETTAGLIO B

SCALA 1 : 10

nessun mezzo e per nessuno scopo, senza autorizzazione della proprieta'.

Il presente disegno, o parte di esso non puo' essere riprodotto in nessuna forma, con

SPESSORE:

Disegnato da:

MATERIALE:

Descrizione:

n° disegno:

lunedì 19 gennaio 2009

Data creazione:

RAGGIO PIEGA

g. 6

g. 7

Connect the appropriate length of duc-

ting to the fan exhaust point and join up

with the ducting to the exte-rior.

Do not x the ducting to the range

hood exhaust outlet with screws-use

duct tape. Use duct tape on all joints.

Re-Circulating Requirements.

If the unit is to be used in the re-circula-

ting mode, t the carbon lter after the

installation is complete (refer to Figure 8).

The carbon lter ts in behind the alu-

minium grease lter. Ensure that the pla-

stic tabs on the carbon lter are facing

outwards otherwise it will be dicult to

remove it later for replacement.

A short length of ductwork must be

connected from the exhaust outlet

on the fan to wherever the air is to

be exhausted (refer to gure 8 A and

B). Allow sucient space to connect the

ductwork to the top of the exhaust ou-

tlet on the fan housing. Do not x the

ducting to the range hood exhaust ou-

tlet with screws, use duct tape. Duct tape

should be used on all joints.

g. 8

nessun mezzo e per nessuno scopo, senza autorizzazione della proprieta'.

Il presente disegno, o parte di esso non puo' essere riprodotto in nessuna forma, con

SPESSORE:

Disegnato da:

MATERIALE:

Descrizione:

n° disegno:

lunedì 19 gennaio 2009

Data creazione:

RAGGIO PIEGA

g. 9

FUNCTION

SIU3 – SIU5 (Fig. 10)

A: Light ON/OFF button

B: Blower Speed 1 (low) or OFF

C: Blower Speed 2 (medium)

D: Blower Speed 3 (high)

E: Hood in operation light

OPERATING PROCEDURES

Read all the instructions before opera-

ting the appliance. Save these instruc-

tions for future reference.

General Advice.

Ensure that the grease lters are in place.

Without these components, operating

blowers could catch on to hair, ngers

and loose clothing. Keep fan, lters and

surfaces clean of grease and fat. Always

turn hood fan ON when cooking. NEVER

leave cooking unattended.

NEVER dispose cigarette ashes, ignitable

substances or any foreign objects into

blowers.

Cooking that generates ame is not re-

commended as this hood is equipped

with a thermal overload that will shut

down the motor if it senses excessive

heat. When frying, oil in the pan can ea-

sily overheat and ignite. Heat oil slowly

in an appropriately sized pot (covering

the entire burner) to reduce the risk of

boiling over and burning.

In the event of a range top grease re,

observe the following:

Switch OFF the range hood. Turn o

the cook top then smother ames with

a close tting lid, cookie sheet or other

metal tray. If the ames do not go out

immediately.

EVACUATE AND CALL THE FIRE DEPART-

MENT.

Never pick up a aming pan – you may

be burned. DO NOT USE WATER inclu-

ding wet dishcloths or towels, as a vio-

lent steam explosion may occur.

g. 10

Generally, the grease lter should be

washed on a regular basis to avoid grea-

se lter res.

The blower should be turned on for ap-

proximately 5 minutes before cooking in

order to establish air currents upward

through the hood. Use the low speeds

for normal use and the higher speeds for

strong odors and fumes.

On the surfaces that are exposed directly

to heat from the cook-top, it is advisable

to clean these regularly to avoid the de-

posits from becoming baked on.

Do not use abrasive cleaning agents as

these will destroy the brushed nish.

Light Bulb Replacement.

(If in doubt, call 866.528.4987)

Turn blower and lights o. Make sure

the lights are cool. If new lights do not

operate, check fuses and be sure globes

and breakers are inserted correctly. Re-

move the glass-blocking ring by prying

out with a sharp, soft instrument such

as a toothpick. (refer to Figure 11) Steel

instruments will scratch the surface. Be

careful that the glass does not fall out

and break.

Do not remove the entire xture (soc-

ket) as this is very dicult to reinstall.

Replace the appropriate bulb. Check

parts brochure or specication sheets

on our website. Wipe both sides of the

glass whilst it is out. Re-insert the glass-

blocking ring and fasten it.

MAINTENANCE

The range hood should provide many

years of trouble free use provided it is

properly maintained. Be sure the lights

are cool before cleaning the hood – they

are halogen and become extremely hot.

Cleaning the Filter.

The aluminium mesh lters should be

washed by hand or in the dishwasher as

required. Damaged and worn lters must

be replaced immediately. (Do not opera-

te blower when lters have been remo-

ved). Allow lters to dry before replacing

them, otherwise water will be drawn into

the blower.

If a carbon lter has been tted, this

must be replaced every 6 months as a

minimum, depending on usage and type

of cooking that is performed.

It is suggested that a spare set of car-

bon lters is kept on hand. These can be

ordered from the supplier of your range

hood.

Cleaning the Hood.

The outside and interior of your hood

should be wiped regularly with a clean,

damp cloth and mild household dish de-

tergent or degreaser.

Use a good quality non-abrasive foa-

ming type stainless steel cleaner for ex-

terior surfaces.

Follow the manufacturers directions. Ge-

nerally the foam is sprayed onto a clean

dry cloth and then applied to the stain-

less steel. Allow the foam to react on the

surface for a few minutes and then wipe

with a clean dry cloth.

nessun mezzo e per nessuno scopo, senza autorizzazione della proprieta'.

Il presente disegno, o parte di esso non puo' essere riprodotto in nessuna forma, con

SPESSORE:

Disegnato da:

MATERIALE:

Descrizione:

n° disegno:

Lampada alogena 20W

GLP-A001

lunedì 19 gennaio 2009

Data creazione:

Andrea Elisei

RAGGIO PIEGA

Andere Handbücher für SUF1

Inhaltsverzeichnis

Andere Sirius Satellite Radio Dunstabzugshaube Handbücher

Sirius Satellite Radio

Sirius Satellite Radio SUM Series Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SLTC919 Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio S-DDH1 Benutzerhandbuch

Sirius Satellite Radio

Sirius Satellite Radio SLT972 Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SLTC 111 Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SLT972 Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SUT951 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SLT105 Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SUT950 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SL926DLTM Series Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SLT972 EM WIFI Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SL906 L 1500 Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio 9351116001063 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio S-DDH1.1 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SU107 Leitfaden

Sirius Satellite Radio

Sirius Satellite Radio SLTC93 Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SLT980 Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio Alfresco SIL25FRESCO1200 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SM923L520 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SUF1 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SL85 Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SUT958 H200 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio ALFRESCO SL80 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SLT976 Kurzanleitung

Beliebte Dunstabzugshaube Handbücher anderer Marken

emmeti

emmeti RECUPA MED A-140 Leitfaden

Nibe

Nibe F135 Bedienungsanleitung

Zephyr

Zephyr Spruce AK9834BS Installationsanleitung

Kuppersberg

Kuppersberg INTRO 60 Montage- und Wartungsanleitung

Hisense

Hisense MH6INBG Bedienungsanleitung

Miele

Miele DA 1255 Bedienungsanleitung

Broan

Broan 46000 Bedienungsanleitung

GE Profile PV977 Originalbetriebsanleitung

FALMEC

FALMEC FFRIA24W5FS Bedienungsanleitung

Whirlpool

Whirlpool RH2600XL-1 SERIES Bedienungsanleitung

ETNA

ETNA AV360RVS Bedienungsanleitung

JUNO

JUNO JDF603E6 Bedienungsanleitung

Miele

Miele DA 6708 D Bedienungsanleitung

Tricity Bendix

Tricity Bendix LE 150 Handbuch

AEG

AEG X68163BV1 Bedienungsanleitung

AEG

AEG 125 D Bedienungsanleitung

Smeg

Smeg KSEV97X Bedienungsanleitung

Nibe

Nibe S Series Benutzerhandbuch