Sirius Satellite Radio SUF1 Bedienungsanleitung

I N S T A L L A T I O N

I N S T R U C T I O N S

CARE AND USE MANUAL FOR:

UNDER CABINET RANGE HOODS

Model covered by these instructions:

SUF1

* * * B E F O R E I N S T A L L A T I O N * * *

ENSURE THERE IS NO VISIBLE OR HIDDEN DAMAGE SUSTAINED

DURING SHIPPING

* * * S H I P P I N G D A M A G E * * *

MUST BE REPORTED WITHIN 5 DAYS OF RECEIPT

Telephone (Toll Free): 866.528.4987 Fax (Toll Free): 866.365.9204

www.siriushoods.com info@siriushoods.com

W A R N I N G

Thank you for purchasing a Sirius Range Hood.

Please read all the instructions in this manual

before installing the appliance.

Save these instructions for future reference.

Only use this appliance as an exhaust ventilation system for the removal

of cooking vapors. DO NOT use to expel flammable substances or any

other materials or vapors.

The installation procedures in this manual are intended for qualified

installers, service technicians or persons with similar qualified

background. DO NOT attempt to install this appliance yourself.

Ensure that electrical power is turned off at source before commencing

installation. All electrical wiring must be properly installed, insulated and

grounded and conform to all applicable codes and standards.

Make sure all existing duct work is clean of grease build up, or duct work

should be replaced, if necessary, to avoid the possibility of a grease fire.

Check all joints on ductwork to ensure proper connection and all joints

should be properly taped. Be careful when cutting through ceilings or

walls not to damage any hidden pipes or electrical wiring. Ensure your

kitchen has sufficient air return vents to replace the exhausted air.

Fan ducts should always be vented to the outside of your home and never

into spaces within walls, ceilings, lofts or attics. Only use rigid, smooth

steel for ducting. The exhaust point of the blower requires a 6” round

connection.

TABLE OF CONTENTS

BEFORE YOU BEGIN 1

DUCTING 1

External Venting Requirements 1

Duct Run Calculation 2

ELECTRICAL 2

Electrical Supply 2

INSTALLATION 3

Connecting Electricity and Ducting 3

Re-Circulating Requirements 4

OPERATING PROCEDURES 5

General Advice 5

Functions 5

MAINTENANCE 6

Cleaning the Filter 6

Cleaning the Hood 6

Light Bulb Replacement 6

WARRANTY 7

DUCTING

(Not applicable if the range hood is

used in re-circulating mode)

WARNING: Do not vent this

appliance into any other ductwork,

spaces between walls, ceilings,

attics, garages or any other confined

space.

B E F O R E Y O U B E G I N

The manufacturer declines all

responsibility in the event of failure

to observe the instructions given

here for installation, maintenance

and suitable operation of the

product. The manufacturer further

declines all responsibility for injury

due to negligence and the warranty

of the unit automatically expires due

to improper maintenance and/or

installation.

BEFORE YOU BEGIN:

It is advisable to test run the

range hood before installation.

Please read this entire manual and

ensure that you are fully conversant

with the requirements and limitations

direct route possible. Always,

wherever reduce the number of

transitions and turns with as few

sharp angles as possible.

Figure 1

Two staggered 45 degree angles are

better than one 90 degree. Make

these turns as far away from the

motor exhaust as possible, with as

much space between each bend.

External Venting Requirements

When planning new ductwork, always

look for the most direct route to the

outside. Venting can be done through

the roof or directly through the back

outside wall. (See Figure 1 )

Only use rigid type metal ducting

(plastic ducting is generally not permit-

ted by code). Flexible ducting could

restrict airflow by up to 50%. Always

fasten connections with sheet metal

screws and tape all joints with certified

Silver Tape or Duct Tape. Do not use

screws to fasten ductwork to

the hood, only use tape as the screws

will stop the dampers from opening

and your hood will not work. This

hood requires a 6” round duct outlet.

You can increase the duct size of the

duct run but never decrease it. Use

the shortest and most

Maximum Run

6” or 3 1/4 x 10” duct 100 FT

Deduct

Each 90 elbow used 15FT

Each 45 elbow used 9FT

Each 6” or 3 1/4 x 10” duct

Transition used 1FT

Each 3’1/4 x 10” to 6”

Transition used 5FT

Side Wall with damper 30FT

Roof Cap 30FT

Electrical Supply

This range hood requires a 120V,

60Hz supply and draws a maximum of

3 amps. The electrical supply to the

range hood should be at least 17”

from the underside of the installed

range hood.

For a typical installation, where the

underside of the range hood will be

30” above the counter top and the

counter top is 36” above the floor

level, the electrical supply should be

76”” above floor level and no further

than 3” to the right (as you face the

wall) of the central axis of the range

hood.

The ducting connection to the hood

must be in line with the central

vertical axis of the range hood 1”

away from the back wall on which

the hood is to be mounted.

Range hoods may interrupt the

proper flow of combustion gases

from fireplaces, gas furnaces and

gas water heaters.

To minimize the risk of drawing

these lethal gases back into the

home, please follow the heating

equipment manufacturers safety

standards and guidelines carefully.

Refer to NFPA and ASHRAE for

additional information.

E L E C T R I C A L

WARNING: All electrical work must

be performed by a qualified

electrician.

Please ensure that the appropriate

electrical codes or prevailing local

building codes and ordinances are

adhered to.

Ensure that the electricity supply is

disconnected at source. Do not use

an extension cord or adapter plug

with this appliance.

This appliance must be grounded.

Connect to a properly grounded

branch circuit, protected by a 15

amp circuit breaker.

Duct Run Calculation

The maximum duct run before

effecting the performance of the

hood is 100’. Calculate your duct run

by measuring linear feet and adding

the elbows, transitions and caps

based on the table alongside.

I N S T A L L A T I O N

Before installing the appliance, in

order not to damage the appliance

itself, the metal grease filter should

be removed by pushing the special

filter handle toward the back side of

the cooker hood and turning it

downwards so to unfasten it from its

slot (refer to figure 2A).

Make a cut-out on the bottom of the

cabinet to hold the appliance by us-

ing the drilling jig provided. This

opening must be 9.8” x 10.2” and at

a distance of 1” from the front edge

of the cabinet (refer to figure 3)

Figure 2

1”

10.2”

9.8”

Center ofthe hood

4.5”

To install the appliance adjust the

position of the stop side-springs

using the appropriate screws,

according to the thickness of the

board. The base of the cabinet must

be from 0.4” to 1” thick (refer to

figure 4).

Min: 0.4”

Max: 1”

Figure 3

Figure 4

Insert the built-in unit in the hole

made in the cabinet until the stop

click of the side-springs is heard and

the hood is temporary held in

position.

Connecting Electricity and

Ducting

Please refer to the Electrical Supply

section on page 2 for the required

location of the electrical supply.

CAUTION: Make sure the power is

turned off at source. Make electrical

connections (refer to Figure 8).

Insert the screws provided in the

holes inside the range hood (refer to

figure 6).

Figure 5

Figure 6

Connect the appropriate length of

ducting to the fan exhaust point and

join up with the ducting to the exte-

rior.

Do not fix the ducting to the range

hood exhaust outlet with screws -

use duct tape. Use duct tape on all

joints.

Re-Circulating Requirements

If the unit is to be used in the

re-circulating mode, fit the carbon

filter after the installation is complete

(refer to Figure 7B).

The carbon filter fits in behind the

aluminium grease filter. Ensure that

the plastic tabs on the carbon filter

are facing outwards otherwise it will

be difficult to remove it later for

replacement.

A short length of ductwork must

be connected from the exhaust

outlet on the fan to wherever the

air is to be exhausted (refer to

figure 8 A and B) Allow sufficient

space to connect the ductwork to the

top of the exhaust outlet on the fan

housing. Do not fix the ducting to

the range hood exhaust outlet with

screws, use duct tape. Duct tape

should be used on all joints.

Figure 7

Ensure that the plastic flaps at the

exhaust outlet for the fan move

freely and have not become jammed

or stuck.

Figure 8

O P E R A T I N G P R O C E D U R E S

Read all the instructions before

operating the appliance.

Save these instructions for future

reference.

General Advice

Ensure that the grease filters are in

place. Without these components,

operating blowers could catch on to

hair, fingers and loose clothing.

Keep fan, filters and surfaces clean

of grease and fat. Always turn hood

fan ON when cooking. NEVER leave

cooking unattended.

NEVER dispose cigarette ashes,

ignitable substances or any foreign

objects into blowers.

Cooking that generates flame is not

recommended as this hood is

equipped with a thermal overload

that will shut down the motor if it

senses excessive heat. When

frying, oil in the pan can easily

overheat and ignite. Heat oil slowly

in an appropriately sized pot

(covering the entire burner) to

reduce the risk of boiling over and

burning

In the event of a range top grease

fire, observe the following:

Switch OFF the range hood. Turn

off the cook top then smother flames

with a close fitting lid, cookie sheet

or other metal tray. If the flames do

not go out immediately.

EVACUATE AND CALL THE FIRE

DEPARTMENT. Never pick up a

flaming pan – you may be burned.

DO NOT USE WATER including wet

dishcloths or towels, as a violent

steam explosion may occur.

Functions

Under Cabinet Controls

A: Light ON/OFF button

B: Blower Speed 1 (low) or OFF

C: Blower Speed 2 (medium)

D: Blower Speed 3 (high)

E: Hood in Operation Light

Generally, the grease filter should

be washed on a regular basis to

avoid grease filter fires.

The blower should be turned on for

approximately 5 minutes before

cooking in order to establish air

currents upward through the hood.

Use the low speeds for normal use

and the higher speeds for strong

odors and fumes.

M A I N T E N A N C E

The range hood should provide

many years of trouble free use

provided it is properly maintained.

Be sure the lights are cool before

cleaning the hood – they are

halogen and become extremely hot.

Cleaning the Filter

The aluminium mesh filters should

be washed by hand or in the

dishwasher as required. Damaged

and worn filters must be replaced

immediately. (Do not operate blower

when filters have been removed).

Allow filters to dry before replacing

them, otherwise water will be drawn

into the blower.

If a carbon filter has been fitted, this

must be replaced every 6 months as

a minimum, depending on usage

and type of cooking that is

performed.

It is suggested that a spare set of

carbon filters is kept on hand.

These can be ordered from the

supplier of your range hood.

Cleaning the Hood

The outside and interior of your hood

should be wiped regularly with a

clean, damp cloth and mild

household dish detergent or

degreaser.

Use a good quality non-abrasive

foaming type stainless steel cleaner

for exterior surfaces.

Follow the manufacturers directions.

Generally the foam is sprayed onto a

clean dry cloth and then applied to

the stainless steel. Allow the foam

to react on the surface for a few

minutes and then wipe with a clean

dry cloth.

On the surfaces that are exposed

directly to heat from the cook-top, it

is advisable to clean these regularly

to avoid the deposits from becoming

baked on.

Do not use abrasive cleaning agents

as these will destroy the brushed

finish.

Light Bulb Replacement

(If in doubt, call 866.528.4987)

Turn blower and lights off. Make

sure the lights are cool. If new lights

do not operate, check fuses and be

sure globes and breakers are in-

serted correctly. Remove the glass-

blocking ring by prying out with a

sharp, soft instrument such as a

toothpick. (refer to Figure 10) Steel

instruments will scratch the surface.

Be careful that the glass does not

fall out and break.

Do not remove the entire fixture

(socket) as this is very difficult to

reinstall. Replace the appropriate

bulb. Check parts brochure or speci-

fication sheets on our website. Wipe

both sides of the glass whilst it is

out. Re-insert the glass-blocking

ring and fasten it.

Figure 10

WARRANTY SERVICE

To qualify for warranty service, you must notify Sirius Range Hoods at the

address stated below or call toll free USA or Canada 1-866-528-4987 and

provide the model number, description of the fault or defect and original date of

purchase. Sirius reserves the right to request proof of original purchase. Sirius

will at its sole option and discretion replace products that arrive damaged

through shipping, provided shipping damage is reported as stated above

within 5 business days of receipt of the shipped product or products.

ONE YEAR SERVICE REPAIR WARRANTY:

During the first year from date of original purchase, Sirius will, at its option,

repair or replace, without charge, any product or part which is found to be

defective under normal use and service.

THREE YEAR PARTS WARRANTY:

For three years from date of purchase, Sirius will provide free of charge,

non-consumable replacement parts which are found to be defective under

normal use and service.

WHO IS COVERED:

Sirius Range Hoods warrants to the original consumer purchaser of its products

that such products will be free from defects in materials and workmanship for a

period of three years from the original date of purchase. There are no other

warranties, express or implied, including, but not limited to, implied warranties of

merchantability or fitness for a particular purpose or application.

WHAT IS NOT COVERED:

This warranty does not extend to filters, lamps, batteries, ducts and ductwork

components. This warranty does not cover normal maintenance and service or

products or parts which have been subject to misuse, negligence, accident,

improper maintenance or repair, faulty installation or installation contrary to

recommended installation instructions. The warranty on glass screens is

limited to manufacturing defects only and expressly excludes cracks and

breakages as a result of faulty installation. Labor and associated costs associated

directly with removal and re-installation are expressly excluded.

The duration of any implied warranty is limited to the three year period as

specified for the express warranty. Some states and provinces do not allow

limitation on how long an implied warranty lasts, so the above limitation may not

apply to you.

7 Register Online! www.siriushoods.com/warranty.htm

Canada: Sirius Range Hoods Ltd

1252 Speers Road Unit 11

Oakville, ON L6L 5N9

USA: Sirius Range Hoods Ltd

1051 Clinton Street

Buffalo, NY 14206

T h r e e Y e a r L i m i t e d W a r r a n t y

Andere Handbücher für SUF1

Inhaltsverzeichnis

Andere Sirius Satellite Radio Dunstabzugshaube Handbücher

Sirius Satellite Radio

Sirius Satellite Radio SU107 Leitfaden

Sirius Satellite Radio

Sirius Satellite Radio SU900 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio S-DDH3 Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SLT966 Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SLTC EM 107 G900 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SLTC928 Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SUT951 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SM923 520 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SUF1 Handbuch

Sirius Satellite Radio

Sirius Satellite Radio SL909 Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SLT980 Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SU909 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SEM1 Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SLT955 Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SL906 Series Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SU900 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SILT-26 Series Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio UP right Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SLT962 Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio STL969 Bedienungs- und Wartungshandbuch

Sirius Satellite Radio

Sirius Satellite Radio SLTC919 520 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SLTC EM 97 900 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SLT972 Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio 9351116001063 Bedienungsanleitung

Beliebte Dunstabzugshaube Handbücher anderer Marken

emmeti

emmeti RECUPA MED A-140 Leitfaden

Nibe

Nibe F135 Bedienungsanleitung

Zephyr

Zephyr Spruce AK9834BS Installationsanleitung

Kuppersberg

Kuppersberg INTRO 60 Montage- und Wartungsanleitung

Hisense

Hisense MH6INBG Bedienungsanleitung

Miele

Miele DA 1255 Bedienungsanleitung

Broan

Broan 46000 Bedienungsanleitung

GE Profile PV977 Originalbetriebsanleitung

FALMEC

FALMEC FFRIA24W5FS Bedienungsanleitung

Whirlpool

Whirlpool RH2600XL-1 SERIES Bedienungsanleitung

ETNA

ETNA AV360RVS Bedienungsanleitung

JUNO

JUNO JDF603E6 Bedienungsanleitung

Miele

Miele DA 6708 D Bedienungsanleitung

Tricity Bendix

Tricity Bendix LE 150 Handbuch

AEG

AEG X68163BV1 Bedienungsanleitung

AEG

AEG 125 D Bedienungsanleitung

Smeg

Smeg KSEV97X Bedienungsanleitung

Nibe

Nibe S Series Benutzerhandbuch