Sirius Satellite Radio SIU3 Bedienungsanleitung

Models covered by this instructions:

Notice d’instruction pour les modèles:

SIU3, SIU5, SU404, SU405, SU401, SIU14, SIU24, SIU8

*** BEFORE INSTALLATION ***

ENSURE THERE IS NO VISIBLE OR HIDDEN DAMAGE SUSTAINED DURING SHIPPING

*** AVANT L’INSTALLATION ***

S’ASSURER QUE LES PRODUITS N’ONT SUBI AUCUN DOMMAGE PENDANT LE TRANSPORT

*** SHIPPING DAMAGE ***

MUST BE REPORTED WITHIN 5 DAYS OF RECEIPT

*** DOMMAGES DE TRANSPORT ***

DOIVENT ÊTRE NOTIFIÉS DANS LES 5 JOURS SUIVANT LA RÉCEPTION

INSTALLATION INSTRUCTIONS

CARE AND USE MANUAL FOR:

NOTICE D’UTILISATION ET D’ENTRETIEN POUR:

ISLAND RANGE HOODS

HOTTES ÎLOT

WARNING

Thank you for purchasing a Sirius Range Hood.

Please read all the instructions in this manual before

installing the appliance.

Save these instructions for future reference.

Only use this appliance as an exhaust ventilation system for the removal of

cooking vapors. DO NOT use to expel ammable substances or any other

materials or vapors.

The installation procedures in this manual are intended for qualied instal-

lers, service technicians or persons with similar qualied background.

DO NOT attempt to install this appliance yourself.

Ensure that electrical power is turned o at source before commencing in-

stallation. All electrical wiring must be properly installed, insulated and

grounded and conform to all applicable codes and standards.

Make sure all existing duct work is clean of grease build up, or duct work

should be replaced, if necessary, to avoid the possibility of a grease re.

Check all joints on ductwork to ensure proper connection and all joints

should be properly taped. Be careful when cutting through ceilings or walls

not to damage any hidden pipes or electrical wiring. Ensure your kitchen has

sucient air return vents to replace the exhausted air.

Fan ducts should always be vented to the outside of your home and never

into spaces within walls, ceilings, lofts or attics. Only use rigid, smooth

steel for ducting. The exhaust point of the blower requires a 6” or 8” round

connection.

TABLE OF CONTENTS

BEFORE YOU BEGIN 4

MINIMUM AND MAXIMUMS 4

DUCTING 4

Duct Run Calculation 5

ELECTRICAL 5

Electrical Supply 5

INSTALLATION 6

Structural preparation for the hood fan installation 6

Fixing the Main Support Bracket 6

Attaching the range hood to the ceiling 7

Connecting Electricity and Ducting 8

Re-Circulating Requirements 8

Schematic of modular island components 9

OPERATING PROCEDURES 11

General Advice 11

Functions 11

MAINTENANCE 14

Cleaning the Filter 14

Cleaning the Hood 14

Substitution of the LED bar 15

WARRANTY 16

BEFORE YOU BEGIN: It is advisable to test

run the range hood before installation.

BEFORE STARTING – please read this en-

tire document and ensure you are fully

conversant with the require-ments and

limitations. These units weigh approxi-

mately 125lbs and therefore require a

minimum of two people to install.

BEFORE YOU BEGIN

The manufacturer declines all responsi-

bility in the event of failure to observe the

instructions given here for installation,

maintenance and suitable operation of

the product. The manufacturer further

declines all responsibility for injury due

to negligence and the warranty of the

unit automatically expires due to impro-

per maintenance and/or installation.

MINIMUM AND MAXIMUMS

Min length of power unit structure with

deector connected = 36.6”

Min length of power unit without de-

ector = 32”.

Max length of power unit structure = 48”.

Recommended height from cook top to

underside of hood = 30” for gas, 25” for

electric.

Use the shortest most direct ductwork

route possible. Only use metal ducting

- plastic ducting is generally not permit-

ted by code. Do not use exible metal

ducting as the ridges of the ducting cau-

se severe air turbulence and will signi-

cantly reduce the eciency of any hood

-THIS TYPE OF DUCTING WILL REDUCE

EFFICIENCY BY 50%.

Vent hoods may interrupt the proper ow

of exhaust gases from re-places, gas

furnaces and gas water heaters. To mini-

mize the risk of drawing these lethal ga-

ses back into the home please follow the

heating equipment manufacturers safety

standards and guidelines. Refer to NFPA

and ASHRAE for additional information.

DUCTING

If vented externally, 6” / 150mm round

ducting must be available for the hood

through the ceiling, in line with the cen-

tral vertical axis of the range hood.

If i’s gas range or cook top recomman-

ded 8”.

This unit must have it’s own ductwork.

Do not under any circumstances vent this

unit into any other ductwork or exhaust

ducting in the building.

PLEASE NOTE THAT THE DUCT OUTLET ON

THE TOP OF THE POWER UNIT IS OFF SET

FROM CENTRE AND THEREFORE AN ADJU-

STABLE 6” ROUND BEND WILL BE REQUIRED

TO LINE THE EXHAUST OUTLET WITH THE

6” HOLE IN THE CEILING MOUNT BRACKET.

Duct Run Calculation.

The maximum duct run before eecting

the performance of the hood is 100’. Cal-

culate your duct run by measuring linear

feet and adding the elbows, transitions

and caps based on the table below.

Electrical Supply.

This appliance requires 120V/60Hz,

3amp electrical supply – ensure an ap-

propriately qualied person completes

the electrical hook-up. The connection

point for the electrical supply is at the top

of the unit, therefore the electrical supply

must be run down from the ceiling alon-

gside the ductwork.

All electrical and venting hook-ups must

be in place before commencing installa-

tion of the hood-fan.

ELECTRICAL

WARNING: All electrical work must be

performed by a qualied electrician.

Please ensure that the appropriate electri-

cal codes or prevailing local building co-

des and ordinances are adhered to.

Ensure that the electricity supply is di-

sconnected at source. Do not use an ex-

tension cord or adapter plug with this

appliance.

This appliance must be grounded. Con-

nect to a properly grounded branch

circuit, protected by a 15 amp circuit

breaker.

Maximum Run

6” or 3 1/4 x 10” duct * 100 FT

Deduct

Each 90 elbow used 15FT

Each 45 elbow used 9FT

Each 6” or 3 1/4 x 10” duct

Transition used 1FT

Each 3” 1/4 x 10” to 6”

Transition used 5FT

Side Wall with damper 30FT

Roof Cap 30FT

* Gas range or gas cook top recomman-

ded 8”.

Do not switch on the lights with the hood

at on any surface as the in-tense heat will

burn the surface and destroy the lamps.

Connect a power supply to the unit and test

all functions.

Installation of the island hood consists

of xing the ceiling Bracket A substantial

members in the ceiling. The bracket must

be xed to the frame by screwing through

the ceiling into the heavy members insi-

de the ceiling. This is critically important

as the entire hood fan hangs from this

position, and ceiling board alone will

not support the weight of the hood fan.

Discard the plastic wall plugs supplied for

xing the bracket to the ceiling – these are

not appropriate for North American struc-

tures.

Fixing the Main Support Brackets

Using Bracket “A” as a template mark the

ceiling where the xing screws “A” will be

positioned – remember the correct orien-

tation from above. Attach bracket “A” to

the ceiling permanently. If re-circulating,

attach the deector to Bracket “A” before

xing it to the ceiling – refer schematic on

page 5.

The 2 brackets for the support of the chi-

mney (Part A) is to be installed to Bracket A

with the screws (C Fig.1) Fix the structure

on the ceiling by inserting the 2 dowels.

INSTALLATION

Structural Preparation for the Hood

Fan Installation.

The island hood weighs approximately 125

lbs. It is therefore imperative that a sub-

stantial structure is prepared in the ceiling

to attach the range hood to. Ideally block

o an area of at least 12”x12” between the

ceiling joists using 2x4’s. Allow for a hole

through the center of this blocking of at

least 6” in diameter through which to pass

the ductwork and electrical cable.

The underside of the hood must not be

closer than 30” from the cook-top and

ideally not higher than 32”above the

cook-top. It is strongly recommended, at

this point, that calculations and measure-

ments be made and all planning and hei-

ghts be nalized. You will need to t the

appropriate length of ducting to the hood

fan before installing it to the ceiling.

Planning should consist of a test assem-

bly of the power unit and telescoping

structure before attempting to mount

everything to the ceiling. By following

this test assembly you will be able to -

nalize the correct length of the assembly

before mounting it to the ceiling.

Test assembly should include actually

attaching the following items together

– refer schematic of components and

“Fixing the main support brackets”

below – Brackets A, B, C, power unit and

deector if re-circulating.

This is also a good time to test the electrical

functioning of the hood before it is instal-

led. Before switching on the light or lights,

ensure the tape holding the globes in place

has been removed.

The globes gets extremely hot and will very

quickly burn the tape and discolor the glo-

bes irreparably. g. 1

Fix Bracket “C” to the power unit with the

nuts and washers supplied (Items “A” on

the schematic on page 5). Please ensure

that the bracket is installed as shown to

enable full ac-cess to the square plastic

black box and the metal electrical junc-

tion box. Slide Bracket “B” over Bracket

“C” (once again ensure full access to the

plastic and electrical boxes is main-tai-

ned) and x it in place, at the previou-

sly calculated length using the machi-

ne screws denoted by items “B” on the

schematic on page 5.

Check that the plastic aps at the exhaust

outlet for the fan move freely and have not

become jammed during shipping or whilst

working with the power unit. Connect an

appropriate length of ducting to the unit.

Do not x the ducting to the outlet with

screws - use DUCT TAPE.

Only for SU 401,SIU3, SIU5, SIU14, SIU24:

Install the glass as per the instructions

contained in the packaging of the glass.

(only for SU401).

Stand the assembled structure on a clean

soft surface. Ensure the underside of the

hood does not get scratched and slide

the chimneys of the assembled structure

from the top down as per the schema-

tic on page 5. Ensure that the holes for

xing the decorative chimney are cor-

rectly orientated with the holes at the

top of bracket A.

Attaching the Range Hood to the Ceiling.

The entire structure that has been pre-

assembled above, must now be hoisted up

to the ceiling. A few things have to happen

at once here: the slots (as discussed below)

need to be engaged and the ductwork must

make connection with the length of duct-

work on the structure.

This will require two strong people –do

not attempt this step on your own. Brac-

ket “B” has slots, position C per Diagram

“A” (refer to page 5), at the top that will

receive the spring clips located on Bracket

“A” –THIS IS A TEMPORARY HOLD ONLY

–DO NOT RELY SOLELY ON THESE CLIPS

TO HOLD THE HOOD UP – THEY WON’T.

Once “hooked” by the spring clips imme-

diately secure the structure with the ma-

chine screws at point “E” on the schematic

on page 5 – this must be done imme-

diately and should not be skipped. Rai-

se the upper chimney to the ceiling and

x it to the bracket “A” with the screws

supplied “D”.

Ensure the entire structure is sturdy - se-

rious injury, death and MAJOR damage

could result should the unit not be well

connected to the frame structure within

the ceiling.

This is of utmost importance – do not go any

further until this has been tested and double

checked – the installer has sole responsibili-

ty for the safe installation of this product.

Only for SU 404-405: Stand the assem-

bled structure on a clean soft surface.

Ensure the underside of the hood does

not get scratched and slide the chimneys

of the assembled structure from the top

down as per the schematic on page 5.

Ensure that the holes for xing the de-

corative chimney are correctly orientated

with the holes at the top of bracket A.

This will require two strong people –do

not attempt this step on your own. Brac-

ket “B” has slots, position C per Diagram

“A” (refer to page 5), at the top that will

receive the spring clips located on Brac-

ket “A” –THIS IS A TEMPORARY HOLD

ONLY –DO NOT RELY SOLELY ON THESE

CLIPS TO HOLD THE HOOD UP – THEY

WON’T. Once “hooked” by the spring

clips immediately secure the structure

with the machine screws at point “E” on

the schematic on page 5 – this must be

done immediately and should not be

skipped.

Ensure the entire structure is sturdy- se-

rious injury, death and MAJOR damage

could result should the unit not be well

connected to the frame structure within

the ceiling.

This is of utmost importance – do not go

any further until this has been tested and

double checked – the installer has sole

responsibility for the safe installation of

this product.

Once the entire structure has been xed

to the ceiling slide the chimneys on the

assembled structure from the bottom up

as per the schematic on page 5. And x

the chimneys with the screws supplied.

Raise the upper chimney to the ceiling

and x it to the bracket “A” with the

screws supplied “D”.

Connecting Electricity and Ducting.

Make sure power is turned o at the

source. Make the electrical connection

(see gure 2). Test the functioning of the

hood. Slide the upper chimney into place

and attach with the machine screws pro-

vided to Bracket “A”.

Re-Circulating Requirements.

Fit the carbon lter after the installation is

complete – these t in behind the alumi-

num grease lter.

A short length of ductwork must be con-

nected from the exhaust outlet up to the

deector (must be purchased with hood).

The deector, after attaching part B with

screws E connects to the top of Bracket

“A” and forces the air out through the

grills on the side of the chimney section

back into the room. (see diagram C).

g. 2

SCHEMATIC OF MODULAR ISLAND COMPONENTS

Diagram c – Deector

Deector FOR SU404

Deector FOR SU405

Part B

Bracket

Deector FOR SIU3, SIU5

Part B

Deector attaches to ceiling mount bracket when island hood is installed in re-circu-

lating mode and the air that has passed through the fat and carbon lters is returned

to the room via a short length of 6” round ductwork attached to the power unit and

deector.

Diagram b – Securing Bracket “A” to “B”

Please note – this is critically important – do not rely on the spring clips.

Diagram A – Main Assembly

FOR SU404

Andere Handbücher für SIU3

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Sirius Satellite Radio Dunstabzugshaube Handbücher

Sirius Satellite Radio

Sirius Satellite Radio SLT955 Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SLT972 Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio Stone SU-DD2-L Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio FSED Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SUF6 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SL909 Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SIU3 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SM927 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SLTC EM 97 900 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SUM Series Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SU909 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SLT950 EM Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SU-DD2-L TC Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SL926DLTM Series Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SU900 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio Valentina Series Bedienungs- und Wartungshandbuch

Sirius Satellite Radio

Sirius Satellite Radio SL85 Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio Alfresco SIL25FRESCO1200 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SU35 TC Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SU1 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SLTC EM 97 900 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio ALFRESCO SL83 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio S-DDH3 Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SLT962 Kurzanleitung

Beliebte Dunstabzugshaube Handbücher anderer Marken

emmeti

emmeti RECUPA MED A-140 Leitfaden

Nibe

Nibe F135 Bedienungsanleitung

Zephyr

Zephyr Spruce AK9834BS Installationsanleitung

Kuppersberg

Kuppersberg INTRO 60 Montage- und Wartungsanleitung

Hisense

Hisense MH6INBG Bedienungsanleitung

Miele

Miele DA 1255 Bedienungsanleitung

Broan

Broan 46000 Bedienungsanleitung

GE Profile PV977 Originalbetriebsanleitung

FALMEC

FALMEC FFRIA24W5FS Bedienungsanleitung

Whirlpool

Whirlpool RH2600XL-1 SERIES Bedienungsanleitung

ETNA

ETNA AV360RVS Bedienungsanleitung

JUNO

JUNO JDF603E6 Bedienungsanleitung

Miele

Miele DA 6708 D Bedienungsanleitung

Tricity Bendix

Tricity Bendix LE 150 Handbuch

AEG

AEG X68163BV1 Bedienungsanleitung

AEG

AEG 125 D Bedienungsanleitung

Smeg

Smeg KSEV97X Bedienungsanleitung

Nibe

Nibe S Series Benutzerhandbuch