Sirius Satellite Radio SU909 Bedienungsanleitung

INSTALLATION INSTRUCTIONS

Models covered by this instructions:

SU909

*** BEFORE INSTALLATION ***

ENSURE THERE IS NO VISIBLE OR HIDDEN DAMAGE SUSTAINED DURING SHIPPING

*** SHIPPING DAMAGE ***

MUST BE REPORTED WITHIN 5 DAYS OF RECEIPT

BUILT-IN RANGE HOODS

CARE AND USE MANUAL FOR:

4 5

6 7

WARNING

Thank you for purchasing a Sirius Range Hood.

Please read all the instructions in this manual before

installing the appliance.

Save these instructions for future reference.

Only use this appliance as an exhaust ventilation system for the removal of coo-

king vapors. DO NOT use to expel ammable substances or any other materials

or vapors.

The installation procedures in this manual are intended for qualied installers, ser-

vice technicians or persons with similar qualied background.

DO NOT attempt to install this appliance yourself.

Ensure that electrical power is turned off at source before commencing installation.

All electrical wiring must be properly installed, insulated and grounded and conform

to all applicable codes and standards.

Make sure all existing duct work is clean of grease build up, or duct work should be

replaced, if necessary, to avoid the possibility of a grease re. Check all joints on

ductwork to ensure proper connection and all joints should be properly taped. Be

careful when cutting through ceilings or walls not to damage any hidden pipes or

electrical wiring. Ensure your kitchen has sufcient air return vents to replace the

exhausted air.

The minimum distance between the cooker surface and the inferior part of the co-

oker hood must be of 650 mm.

Fan ducts should always be vented to the outside of your home and never into

spaces within walls, ceilings, lofts or attics. Only use rigid, smooth steel for ducting.

The exhaust point of the blower requires a 6” round or 8” connection.

TABLE OF CONTENTS

BEFORE YOU BEGIN 7

DUCTING

External venting Requirements 7

ELECTRICAL

Electrical Supply 8

INSTALLATION

Installing 9

Re-Circulating Requirements 10

OPERATING PROCEDURES

General Advice 11

Functions 11

TECHNICAL DATA

Standard conguration 12

Generating a new transmission code 12

Learning the new transmission code 12

MAINTENANCE

Cleaning the Filter 14

Cleaning the Hood 14

Replace led lamp 14

WARRANTY 16

BEFORE YOU BEGIN: It is advisable to

test run the range hood before installa-

tion.

BEFORE STARTING – please read this

entire document and ensure you are fully

conversant with the requirements and limi-

tations. These units weigh approximately

125lbs and therefore require a minimum of

two people to install.

BEFORE YOU BEGIN

The manufacturer declines all responsibility

in the event of failure to observe the instruc-

tions given here for installation, maintenan-

ce and suitable operation of the product. The

manufacturer further declines all responsibi-

lity for injury due to negligence and the war-

ranty of the unit automatically expires due

to improper maintenance and/or installation.

Always fasten connections with sheet metal

screws and tape all joints with certied Silver

Tape or Duct Tape. Do not use screws to fa-

sten ductwork to the hood, only use tape as

the screws will stop the dampers from ope-

ning and your hood will not work. This hood

re-quires a 6” round or 8” duct outlet. You

can increase the duct size of the duct run

but never decrease it. Use the shortest and

most direct route possible. Always, where-

ver possible, reduce the number of transi-

tions and turns with as few sharp angles as

possible. Two staggered 45 degree angles

are better than one 90 degree. Make these

turns as far away from the motor exhaust as

possible, with as much space between each

bend.

DUCTING

(Not applicable if the range hood is used in

re-circulating mode).

WARNING: Do not vent this appliance into

any other ductwork, spaces between walls,

ceilings, attics, garages or any other con-

ned space.

External Venting Requirements.

When planning new ductwork, always look

for the most direct route to the outside. Ven-

ting can be done through the roof or directly

through the back outside wall. (See Figure

12 and 13) Only use rigid type metal ducting

(plastic ducting is generally not permitted by

code). Flexible ducting could restrict airow

by up to 50%.

g. 12 g. 13

Electrical Supply.

This appliance requires 120V/60Hz, 3amp

electrical supply – ensure an appropriately

qualied person completes the electrical ho-

ok-up. The connection point for the electrical

supply is at the top of the unit, therefore the

electrical supply must be run down from the

ceiling alongside the ductwork.

All electrical and venting hook-ups must be in

place before commencing installation of the

hood-fan.

ELECTRICAL

WARNING: All electrical work must be

performed by a qualied electrician.

Please ensure that the appropriate electrical

codes or prevailing local building codes and

ordinances are adhered to.

Ensure that the electricity supply is discon-

nected at source. Do not use an extension

cord or adapter plug with this appliance.

This appliance must be grounded. Connect

to a properly grounded branch circuit, pro-

tected by a 15 amp circuit breaker.

INSTALLATION

Installing SU909

Before proceeding with the installation, in

order to avoid damage to the appliance, ple

ase remove the metallic grease lter.

To remove the metallic grease lter, use the

special handle and rotate down the lter, ta

king care to unhook it from its seat (g.1).

To remove the oil collector, loosen the two

screws as indicated in g. 1/A.

On the furniture make a hole with these di-

mensions:

SL909 Cm 140: 53”3/4 - 16”1/8 (1365mm x 410mm.)

SL909 Cm 86: 32”15/32 - 16”1/8 (825mm x 410mm.)

SL909 46”: 44”23/32 X 16 “1/8 (1136mm x 410mm.)

The range hood provides the air outlet on

up per side or alternatively on the rear side,

according to the needs of installation.

The standard arrangement of air outlet is on

the upper side, move it to the rear side of

product following these instructions:

Disconnect the electrical part of the motor,

re moving the electric connector.

Move the product on a plain surface then

remove all the specic perimeter screws as

shown in g. 2, pick up the upper side as

shown in g. 3 and rotate it by 180°.

Remove all the six secure screws of the mo-

tors, extract the motors from the metal body

and move them into the specic side ope-

ning as indicated in g. 4 and g. 5.

The lid has to be moved on the upper side

as shown in g. 5.

To assemble the metal body put back on the

screws previously removed as shown in g. 2.

Pay close attention: they must correspond

to the blocking screws of the wiring system.

Make the electrical connection (g. 6).

Install the air outlet ange xing the screws

provided where the outputs of the two mo-

tors are (g. 7); this is not used in the one-

motor version and external motor (remote

motor) version.

Fix the product with the supplied screws as

shown on g. 8.

At this point take the oil collector and hook

it on the appropriate hole of the hood. Plea

se be careful not to scratch and damage the

product. (Fig. 9).

Fix the oil collector securing the pommels of

the range hood (Fig. 10).

Re-install the metallic grease lter previou

sly removed.

g. 14

CAUTION: Make sure the power is turned

off at source. Make electrical connections

(refer to Figure 14). Ensure that the plastic

aps at the exhaust outlet of the fan move

freely and have not become jammed or

stuck.

Connect the appropriate length of ducting to

the fan exhaust point and connect the duc-

ting to the exterior.

Do not x the ducting to the range hood

exhaust outlet with screws: use duct

tape. Use duct tape on all joints.

Re-Circulating Requirements.

If the unit is to be used in the recirculating

mode, t the carbon lters after the installa-

tion is completed (refer to Figure 15).

The carbon lter ts in behind the aluminium

grease lter. Ensure that the plastic tabs on

the carbon lter are facing outwards other-

wise it will be difcult to remove it later for

replacement.

A short length of ductwork must be con-

nected from the exhaust outlet on the fan

to wherever the air is to be exhausted.

Allow sufcient space to connect the duct-

work to the top of the exhaust outlet on the

fan housing. Do not x the ducting to the

range hood exhaust outlet with screws, use

duct tape. Duct tape should be used on all

joints.

g. 15

Inhaltsverzeichnis

Andere Sirius Satellite Radio Dunstabzugshaube Handbücher

Sirius Satellite Radio

Sirius Satellite Radio Valentina SLT958EM Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SM923 52 Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SDD2ELEMTC Series Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SUT950 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SL926 Series Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SILT-26 Series Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SLTC93 Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio FSED Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio UP right Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SU900 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SL85 Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SLTC928 Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SLTC919 520 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio ALFRESCO SLEM80 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SL906 DL Series Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SL906 Series Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SILT-21 B Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SM927 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SL926DLTM Series Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio Downdraft S-DD18 Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SLT960 Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SLT105 Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SLT976 Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SIL-EM490X Kurzanleitung

Beliebte Dunstabzugshaube Handbücher anderer Marken

emmeti

emmeti RECUPA MED A-140 Leitfaden

Nibe

Nibe F135 Bedienungsanleitung

Zephyr

Zephyr Spruce AK9834BS Installationsanleitung

Kuppersberg

Kuppersberg INTRO 60 Montage- und Wartungsanleitung

Hisense

Hisense MH6INBG Bedienungsanleitung

Miele

Miele DA 1255 Bedienungsanleitung

Broan

Broan 46000 Bedienungsanleitung

GE Profile PV977 Originalbetriebsanleitung

FALMEC

FALMEC FFRIA24W5FS Bedienungsanleitung

Whirlpool

Whirlpool RH2600XL-1 SERIES Bedienungsanleitung

ETNA

ETNA AV360RVS Bedienungsanleitung

JUNO

JUNO JDF603E6 Bedienungsanleitung

Miele

Miele DA 6708 D Bedienungsanleitung

Tricity Bendix

Tricity Bendix LE 150 Handbuch

AEG

AEG X68163BV1 Bedienungsanleitung

AEG

AEG 125 D Bedienungsanleitung

Smeg

Smeg KSEV97X Bedienungsanleitung

Nibe

Nibe S Series Benutzerhandbuch