Sirius Satellite Radio SU35 TC Bedienungsanleitung

INSTALLATION INSTRUCTIONS

Models covered by this instructions:

SU35 TC - SU109

*** BEFORE INSTALLATION ***

ENSURE THERE IS NO VISIBLE OR HIDDEN DAMAGE SUSTAINED DURING SHIPPING

*** SHIPPING DAMAGE ***

MUST BE REPORTED WITHIN 5 DAYS OF RECEIPT

WALL RANGE HOODS

CARE AND USE MANUAL FOR:

WARNING

Thank you for purchasing a Sirius Range Hood.

Please read all the instructions in this manual before

installing the appliance.

Save these instructions for future reference.

Only use this appliance as an exhaust ventilation system for the removal of coo-

king vapors. DO NOT use to expel ammable substances or any other materials

or vapors.

The installation procedures in this manual are intended for qualied installers, ser-

vice technicians or persons with similar qualied background.

DO NOT attempt to install this appliance yourself.

Ensure that electrical power is turned off at source before commencing installation.

All electrical wiring must be properly installed, insulated and grounded and conform

to all applicable codes and standards.

Make sure all existing duct work is clean of grease build up, or duct work should be

replaced, if necessary, to avoid the possibility of a grease re. Check all joints on

ductwork to ensure proper connection and all joints should be properly taped. Be

careful when cutting through ceilings or walls not to damage any hidden pipes or

electrical wiring. Ensure your kitchen has sufcient air return vents to replace the

exhausted air.

The minimum distance between en the cooker surface and the inferior part of the

cooker hood must be of 650 mm.

Fan ducts should always be vented to the outside of your home and never into

spaces within walls, ceilings, lofts or attics. Only use rigid, smooth steel for ducting.

The exhaust point of the blower requires a 6” round or 8” connection.

TABLE OF CONTENTS

BEFORE YOU BEGIN 4

DUCTING 4

External Venting Requirements 4

Duct Run Calculation 4

ELECTRICAL 5

Electrical Supply 5

USES 6

INSTALLATION 7

OPERATING PROCEDURES 9

Working 10

MAINTENANCE 11

Light Bulb Replacement 11

Substitution of the LED bar 12

WARRANTY 13

BEFORE YOU BEGIN: It is advisable to

test run the range hood before installa-

tion.

BEFORE STARTING – please read this

entire document and ensure you are fully

conversant with the require-ments and li-

mitations. These units weigh approximately

125lbs and therefore require a minimum of

two people to install.

BEFORE YOU BEGIN

The manufacturer declines all responsibility

in the event of failure to observe the instruc-

tions given here for installation, maintenan-

ce and suitable operation of the product. The

manufacturer further declines all responsibi-

lity for injury due to negligence and the war-

ranty of the unit automatically expires due

to improper maintenance and/or installation.

Only use rigid type metal ducting (plastic

ducting is generally not permit-ted by code).

Flexible ducting could restrict airow by up

to 50%. Always fasten connections with she-

et metal screws and tape all joints with certi-

ed Silver Tape or Duct Tape.

Do not use screws to fasten ductwork to

the hood, only use tape as the screws will

stop the dampers from opening and your

hood will not work. This hood requires 8’’ for

the models with 2 motors. You can increase

the duct size of the duct run but never de-

crease it.

Use the shortest and most direct route pos-

sible. Always, wherever reduce the number

of transitions and turns with as few sharp

angles as possible.

Two staggered 45 degree angles are better

than one 90 degree. Make these turns as far

away from the motor exhaust as possible,

with as much space between each bend as

possible.

Duct Run Calculation

The maximum duct run before effecting the

performance of the hood is 100’. Calculate

your duct run by measuring linear feet and

adding the elbows, transitions and caps ba-

sed on the table alongside.

DUCTING

(Not applicable if the range hood is used in

re-circulating mode).

WARNING: Do not vent this appliance into

any other ductwork, spaces between walls,

ceilings, attics, garages or any other con-

ned space.

External Venting Requirements.

When planning new ductwork, always look

for the most direct route to the outside. Ven-

ting can be done through the roof or directly

through the back outside wall.

Electrical Supply.

This range hood requires a 120V, 60Hz sup-

ply and draws a maximum of 3 amps. The

electrical supply to the range hood should be

at least 17” from the underside of the instal-

led range hood.

For a typical installation, where the undersi-

de of the range hood will be 30” above the

counter top and the counter top is 36” above

the oor level, the electrical supply should be

76” above oor level and no further than 3” to

the right (as you face the wall) of the central

axis of the range hood.

ELECTRICAL

WARNING: All electrical work must be

performed by a qualied electrician.

Please ensure that the appropriate electrical

codes or prevailing local building codes and

ordinances are adhered to.

Ensure that the electricity supply is discon-

nected at source. Do not use an extension

cord or adapter plug with this appliance.

This appliance must be grounded. Connect

to a properly grounded branch circuit, pro-

tected by a 15 amp circuit breaker.

The ducting connection to the hood must

be in line with the central vertical axis of the

range hood 1” away from the back wall on

which the hood is to be mounted. The 1” is

important to enable the ceiling bracket to

pass behind the ductwork servicing the ran-

ge hood.

Range hoods may interrupt the proper ow

of combustion gases from replaces, gas

furnaces and gas water heaters.

To minimize the risk of drawing these lethal

gases back into the home, please follow the

heating equipment manufacturers safety

standards and guidelines carefully.

Refer to NFPA and ASHRAE for additional

information.

Maximum Run

6” or 3 1/4 x 10” duct * 100 FT

Deduct

Each 90 elbow used 15FT

Each 45 elbow used 9FT

Each 6” or 3 1/4 x 10” duct

Transition used 1FT

Each 3” 1/4 x 10” to 6”

Transition used 5FT

Side Wall with damper 30FT

Roof Cap 30FT

The appliance can be used both in ltering

and sucking versions.

In the ltering version, air and fumes conve-

yed by the appliance are puried by both a

grease lter and an active charcoal lter and

are then released and re-circulated into the

environment.

USES

In the sucking version, fumes are conveyed

directly outside, through an evacuating duct.

The use of a charcoal lter is not needed.

Before installation, in order to avoid damage

to the appliance, remove the grease lter.

The removal of the of the metal grease-lter

is done by pushing the special lter handle

towards the rear side of the cooker hood,

making it rotate downwards.

INSTALLATION

perforate the wall according to the pattern

indicated by the jig itself, being careful not to

damage water pipes or electrical wires. The

wall should be perforated using a Ø 8 mm

wall drill. Insert the proper plastic reinforce-

ments into the holes that have been created.

The hood-bearing stirrups are applied using

the screws included with the equipment.

Using the special drilling jig,

The air outlet of the product is oriented up-

wards: in the case that one prefers the air

outlet towards the rear side of the appliance

, it is only necessary to replace the air rele-

ase piece with the other one supplied with

the appliance.

In the 30” version, it is possible to orient the

air outlet towards the rear side of the cooker

hood by rotating the sucking unit.

Remove the xing screws shown,

take the sucking unit out, rotate and reinsert it

into the desired position, and then place again

the screws that had been removed. To comple-

te installation, insert the two xing screws into

the rear side of the cooker hood, into the two

holes that were created beforehand. Before -

xing the chimney in place, place the electrical

feeding equipment into the decorative pipe as

well as the related electrical connection.

Hook the cooker hood into the bearings,

then adjust vertically and horizontally the

position of the appliance, acting on the spe-

cial regulating metric screws.

After having xed the hood-bearing stirrup of

the upper chimney, raise and block it with the

two side screws.

In the case of the sucking version, connect the

ange of the cooker hood to the air outlet hole,

which is already prepared, through a suitable

pipe. Position the two chimneys on the coo-

ker hood in their proper seat, raising the upper

chimney to the desired height and x the appro-

priate bearings using the included screws and

reinforcements.

OPERATING PROCEDURES

it senses excessive heat. When frying, oil in

the pan can easily overheat and ignite. Heat

oil slowly in an appropriately sized pot (co-

vering the entire burner) to reduce the risk of

boiling over and burning.

In the event of a range top grease re, ob

serve the following: Switch OFF the range

hood. Turn off the cook top then smother a-

mes with a close tting lid, cookie sheet or

other metal tray. If the ames do not go out

immediately.

EVACUATE AND CALL THE FIRE DE PART-

MENT.

Never pick up a aming pan – you may be

burned. DO NOT USE WATER including wet

dishcloths or towels, as a violent steam ex-

plosion may occur.

Read all the instructions before operating the

appliance. Save these instructions for future

reference.

General Advice.

Ensure that the grease lters are in place.

Without these components, operating blo

wers could catch on to hair, ngers and lo

ose clothing.

Keep fan, lters and surfaces clean of gre

ase and fat. Always turn hood fan ON when

cooking. NEVER leave cooking unattended.

NEVER dispose cigarette ashes, ignitable

substances or any foreign objects into blo

wers.

Cooking that generates ame is not recom

mended as this hood is equipped with a ther-

mal overload that will shut down the mo tor if

For the Touch Control “ROSSO” (RED) ver-

sion, it is possible to set the shut off of the

lighting function of the keypad by pressing

the light key (A) for 6 seconds (this opera-

tion must be done with both lights and motor

switched off). This function permits for the au-

tomatic shutoff of the keypad after 10 secon-

ds from shutoff of the lights and the motor. To

re-activate the keypad it is sufcient to set a

function. To keep the lighting of the keypad

always on, press the light key for 6 seconds

(this operation must be done with both light

and motor switched off).

FUNCTION SU35 TC

The functions of the keys of the Touch Con-

trol keypad (push button control panel) are

described below:

A: LIGHT SWITCH ON/OFF

B: SPEED REDUCTION / OFF MOTOR

C: SPEED INDICATORS

D: ON MOTOR / SPEED INCREASE

E: TIMER 10 min.

FUNCTION SU109

“Manual touch buttons”

A: Light ON/OFF button

B: Blower Speed 1 (low) or OFF

C: Blower Speed 2 (medium)

D: Blower Speed 3 (high)

E: Blower Speed 4 (intensive)

F: 10 Minute Timer

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Sirius Satellite Radio Dunstabzugshaube Handbücher

Sirius Satellite Radio

Sirius Satellite Radio S900 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SL85 Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SUT958 H200 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SDD2ELEMTC Series Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SLT966 Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SILT-21 B Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio S-DDH3 Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio Alfresco SIL25FRESCO1200 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SM923 52 Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SU909 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio STL969 Bedienungs- und Wartungshandbuch

Sirius Satellite Radio

Sirius Satellite Radio SEM51 Leitfaden

Sirius Satellite Radio

Sirius Satellite Radio FSED Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio S-DDH1.1 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SU1 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SU-DD2-L TC Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SLT960 Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SLT955 Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SLTC919 520 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio Downdraft S-DD18 Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SL909 Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SLT950 EM Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SUT950 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SDD2EMIX60 Bedienungsanleitung

Beliebte Dunstabzugshaube Handbücher anderer Marken

emmeti

emmeti RECUPA MED A-140 Leitfaden

Nibe

Nibe F135 Bedienungsanleitung

Zephyr

Zephyr Spruce AK9834BS Installationsanleitung

Kuppersberg

Kuppersberg INTRO 60 Montage- und Wartungsanleitung

Hisense

Hisense MH6INBG Bedienungsanleitung

Miele

Miele DA 1255 Bedienungsanleitung

Broan

Broan 46000 Bedienungsanleitung

GE Profile PV977 Originalbetriebsanleitung

FALMEC

FALMEC FFRIA24W5FS Bedienungsanleitung

Whirlpool

Whirlpool RH2600XL-1 SERIES Bedienungsanleitung

ETNA

ETNA AV360RVS Bedienungsanleitung

JUNO

JUNO JDF603E6 Bedienungsanleitung

Miele

Miele DA 6708 D Bedienungsanleitung

Tricity Bendix

Tricity Bendix LE 150 Handbuch

AEG

AEG X68163BV1 Bedienungsanleitung

AEG

AEG 125 D Bedienungsanleitung

Smeg

Smeg KSEV97X Bedienungsanleitung

Nibe

Nibe S Series Benutzerhandbuch