Sirius Satellite Radio SU900 Bedienungsanleitung

INSTALLATION INSTRUCTIONS

CARE AND USE MANUAL FOR:

NOTICE D’UTILISATION ET D’ENTRETIEN POUR:

BUILT-IN RANGE HOODS

HOTTES ÎLOT

Models covered by this instructions:

Notice d’instruction pour les modèles:

SU900, SUT900, SUE900, SU901, SU902, SU903, SU908, SU923, SUE923

*** BEFORE INSTALLATION ***

ENSURE THERE IS NO VISIBLE OR HIDDEN DAMAGE SUSTAINED DURING SHIPPING

*** AVANT L’INSTALLATION ***

S’ASSURER QUE LES PRODUITS N’ONT SUBI AUCUN DOMMAGE PENDANT LE TRANSPORT

*** SHIPPING DAMAGE ***

MUST BE REPORTED WITHIN 5 DAYS OF RECEIPT

*** DOMMAGES DE TRANSPORT ***

DOIVENT ÊTRE NOTIFIÉS DANS LES 5 JOURS SUIVANT LA RÉCEPTION

lunedì 16 aprile 2007

SPESSORE:

MATERIALE:

RAGGIO PIEGA

Il presente disegno, o parte di esso non puo' essere riprodotto in nessuna forma, con

Descrizione:

n° disegno:

nessun mezzo e per nessuno scopo, senza autorizzazione della proprieta'.

Disegnato da: Data creazione:

lunedì 16 aprile 2007

SPESSORE:

MATERIALE:

RAGGIO PIEGA

Il presente disegno, o parte di esso non puo' essere riprodotto in nessuna forma, con

nessun mezzo e per nessuno scopo, senza autorizzazione della proprieta'.

Disegnato da:

Descrizione:

n° disegno:

Data creazione:

lunedì 16 aprile 2007

SPESSORE:

MATERIALE:

RAGGIO PIEGA

Il presente disegno, o parte di esso non puo' essere riprodotto in nessuna forma, con

nessun mezzo e per nessuno scopo, senza autorizzazione della proprieta'.

Disegnato da:

Descrizione:

n° disegno:

Data creazione:

15 16

WARNING

Thank you for purchasing a Sirius Range Hood.

Please read all the instructions in this manual before in-

stalling the appliance.

Save these instructions for future reference.

Only use this appliance as an exhaust ventilation system for the removal of coo-

king vapors. DO NOT use to expel ammable substances or any other materials

or vapors.

The installation procedures in this manual are intended for qualied installers, ser-

vice technicians or persons with similar qualied background.

DO NOT attempt to install this appliance yourself.

Ensure that electrical power is turned off at source before commencing installation.

All electrical wiring must be properly installed, insulated and grounded and conform

to all applicable codes and standards.

Make sure all existing duct work is clean of grease build up, or duct work should be

replaced, if necessary, to avoid the possibility of a grease re. Check all joints on

ductwork to ensure proper connection and all joints should be properly taped. Be

careful when cutting through ceilings or walls not to damage any hidden pipes or

electrical wiring. Ensure your kitchen has sufcient air return vents to replace the

exhausted air.

The minimum distance between en the cooker surface and the inferior part of the

cooker hood must be of 650 mm.

Fan ducts should always be vented to the outside of your home and never into

spaces within walls, ceilings, lofts or attics. Only use rigid, smooth steel for ducting.

The exhaust point of the blower requires a 6” round connection.

TABLE OF CONTENTS

BEFORE YOU BEGIN 7

DUCTING 7

External venting Requirements 7

Duct Run Calculation 8

ELECTRICAL 8

Electrical Supply 8

INSTALLATION 9

Applications 9

Connecting Electricity and Ducting 10

Re-Circulating Requirements 11

OPERATING PROCEDURES 12

General Advice 12

Functions 12

MAINTENANCE 15

Cleaning the Filter 15

Cleaning the Hood 15

Replace led lamp 15

WARRANTY 16

BEFORE YOU BEGIN: It is advisable to test

run the range hood before installation.

BEFORE STARTING – please read this

entire document and ensure you are fully

conversant with the require-ments and li-

mitations. These units weigh approximately

125lbs and therefore require a minimum of

two people to install.

BEFORE YOU BEGIN

The manufacturer declines all responsibility

in the event of failure to observe the instruc-

tions given here for installation, maintenance

and suitable operation of the product. The

manufacturer further declines all responsibi-

lity for injury due to negligence and the war-

ranty of the unit automatically expires due

to improper maintenance and/or installation.

Always fasten connections with sheet metal

screws and tape all joints with certied Sil-

ver Tape or Duct Tape. Do not use screws to

fasten ductwork to the hood, only use tape

as the screws will stop the dampers from

opening and your hood will not work. This

hood re-quires a 6” round duct outlet. You

can increase the duct size of the duct run

but never decrease it. Use the shortest and

most direct route possible. Always, where-

ver possible, reduce the number of transi-

tions and turns with as few sharp angles as

possible. Two staggered 45 degree angles

are better than one 90 degree. Make these

turns as far away from the motor exhaust as

possible, with as much space between each

bend.

DUCTING

(Not applicable if the range hood is used in

re-circulating mode).

WARNING: Do not vent this appliance into

any other ductwork, spaces between walls,

ceilings, attics, garages or any other con-

ned space.

External Venting Requirements.

When planning new ductwork, always look

for the most direct route to the outside. Ven-

ting can be done through the roof or directly

through the back outside wall. (See Figure

1 and 2) Only use rigid type metal ducting

(plastic ducting is generally not permitted by

code). Flexible ducting could restrict airow

by up to 50%.

Duct Run Calculation.

The maximum duct run before effecting the

performance of the hood is 100’. Calculate

your duct run by measuring linear feet and

adding the elbows, transitions and caps ba-

sed on the table below.

Maximum Run

6” or 3 1/4 x 10” duct 100 FT

Deduct

Each 90 elbow used 15FT

Each 45 elbow used 9FT

Each 6” or 3 1/4 x 10” duct

Transition used 1FT

Each 3’1/4 x 10” to 6”

Transition used 5FT

Side Wall with damper 30FT

Roof Cap 30FT

Electrical Supply.

This appliance requires 120V/60Hz, 3amp

electrical supply - ensure an appropriately

qualied person completes the electrical ho-

ok-up. The connection point for the electrical

supply is at the top of the unit, therefore the

electrical supply must be run down from the

ceiling alongside the ductwork.

All electrical and venting hook-ups must be in

place before commencing installation of the

hood-fan.

ELECTRICAL

WARNING: All electrical work must be

performed by a qualied electrician.

Please ensure that the appropriate electrical

codes or prevailing local building codes and

ordinances are adhered to.

Ensure that the electricity supply is discon-

nected at source. Do not use an extension

cord or adapter plug with this appliance.

This appliance must be grounded. Connect

to a properly grounded branch circuit, pro-

tected by a 15 amp circuit breaker.

The ducting connection to the hood must be

in line with the central vertical axis of the

range hood 1” away from the back wall on

which the hood is to be mounted.

Range hoods may interrupt the proper ow

of combustion gases from replaces, gas

furnaces and gas water heaters.

To minimize the risk of drawing these lethal

gases back into the home, please follow the

heating equipment manufacturers safety

standards and guidelines carefully.

Refer to NFPA and ASHRAE for additional

information.

SU902 10” 25/64 X 26” ½

SU903 27” 9” 15/16 X 25” 9/16

SU903 36” 9” 15/16 X 33” 7/16

SU908 12” 5/8 X 26” 2/2

SU923 - SUE923 20” 19” 7/8 X 10” 5/8

SU923 - SUE923 27” 26” 31/32 X 10” 5/8

If Sch31A or a Pro Liner are being used,

they can be held up under the cabinet and

used as a template.

If Sch31A or a Pro Liner are to be used for

under cabinet application, they should be

installed now.

Installing a SCH31A with SU900 - SUT900

– SUE900. Hold the Sch31A under the ca-

binet and Screw it to the 4 hole locations.

Make sure it lines up with the cut out in

your cabinet. The power pack has pressu-

re springs (to be adjusted) on the front and

back that will “hook” onto the top surface of

the underside of the hood when it is pushed

up into the hole that has been cut out (refer

to gure 3).

Installing SU900 - SUT900 – SUE900 wi-

thout a SCH31A. The power pack has pres-

sure springs (to be adjusted) on the front

and back that will “hook” onto the top sur-

face of the underside of the hood when it is

pushed up into the hole that has been cut

out (refer to gure 3).

INSTALLATION

Applications

The SU900 - SUT900 – SUE900 can either

be installed inside a wall cabinet (provided

the inside depth is greater than 11”) or used

in a custom designed wooden hood. Whe-

re installed directly into a wall cabinet, there

are two options:

Directly into the cabinet without any form of

hood. Directly into the cabinet together with

Sch31A where the Sch31A acts as a liner

hood and is attached to either the underside

of the cabinet or into the sides of the cabi-

nets alongside.

The SU901 can either be installed inside a

wall cabinet or used in a custom designed

wooden hood. Where installed directly into

a wall cabinet, there are two options:

Directly into the cabinet or directly into the

cabinet together with the adjustable Pro li-

ners where the adjustable Pro liners act as

a cabinet protection against the heat. The

depth of the adjustable pro liners can vary

from 23.5” to 25.9” )

The SU902 and SU903 can either be instal-

led inside a wall cabinet or used in a custom

designed wooden hood.

Depending on which model is used, prepa-

re a cut-out in the underside of the wooden

hood to allow the powerpack to t up into the

hood using the following dimensions:

SU900 - SUT900 – SUE900 20”

10” 3/8 X 19” 19/32

SU900 - SUT900 – SUE900 27”

10” 3/8 X 26” 11/16

SU901

32” 13/32 X 16” 3/16

There are four holes on the inside of the

SUT900 to x the unit into the edge of the

base of the wooden hood (refer to gure 4).

Installing a Adjustable Pro Liner with

SU901. Once the cut out has been done in-

stall the Adjustable Pro Liner and make sure

it lines up with the cut out in your cabinet.

Screw it to the 4 hole locations (refer to -

gure 5).

Install the front part of the liner adjusting it to

the depth of the cabinet. (refer to gure 6).

Screw it to the 3 hole locations.

Attention: be sure the cabinet has a mini-

mum thickness of 0.75” on the 4 sides.

The power pack has pressure springs (to

be adjusted) on the front and back that will

“hook” onto the top surface of the underside

of the hood when it is pushed up into the

hole that has been cut out (refer to gure 3).

Installing SU902. The power pack has

pressure springs (to be adjusted) on the

front and back that will “hook” onto the top

surface of the underside of the hood when it

is pushed up into the hole that has been cut

out (refer to gure 3).

Installing SU903. Before installing the unit,

open the central panel (see gure 7) and re-

move it (see gure 8).

The power pack has pressure springs (to

be adjusted) on the front and back that will

“hook” onto the top surface of the underside

of the hood when it is pushed up into the

hole that has been cut out (refer to gure

9). There are six holes on the inside of the

SU903 to x the unit into the edge of the

base of the wooden cabinet (refer to gure

10).

Installing SU908

There are four holes on the inside of the SU908

to x the unit intothe edge of the base of the wo-

oden hood (refer to gure 4).

Installing SU923 - SUE923

Before installing the appliance, remuve the

me tal grase lter. It can be removed by

pushing its special handle toward the back-

side of the cooker hood and turning the lter

downwards so to unfasten it from its slot (re-

fer to gure 11).

The power pack has pressure springs (to

be adjusted) on the front and back that will

“hook” onto the top surface of the underside

of the hood when it is pushed up into the

hole that has been cut out (refer to gure 3).

There are eight holes on the inside of the

SU923 - SUE923 to x the unit into the edge

of the base of the wooden cabinet (refer to

gure 12).

Connecting Electricity and Ducting.

Please refer to the Electrical Supply section

on page 2 for the required location of the

electrical supply.

CAUTION: Make sure the power is turned

off at source. Make electrical connections

(refer to Figure 13). Ensure that the plastic

aps at the exhaust outlet for the fan move

freely and have not become jammed or

stuck.

Andere Handbücher für SU900

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Sirius Satellite Radio Dunstabzugshaube Handbücher

Sirius Satellite Radio

Sirius Satellite Radio ALFRESCO SL80 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SLTC919 520 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SLT966 Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SM923 52 Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SILT-26 Series Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SIL-EM490X Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SL906 DL Series Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SLT960 Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SILT-21 B Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SDD2EMIX60 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SLT962 Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio STL969 Bedienungs- und Wartungshandbuch

Sirius Satellite Radio

Sirius Satellite Radio S-DD2-L EMIC 880 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SU906 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SL913 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SLT972 Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SLTC93 Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SLT972 Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SLT972 EM WIFI Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SUT950 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio S-DDH1 Benutzerhandbuch

Sirius Satellite Radio

Sirius Satellite Radio S900 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SLTC EM 97 900 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SLT955 Kurzanleitung

Beliebte Dunstabzugshaube Handbücher anderer Marken

emmeti

emmeti RECUPA MED A-140 Leitfaden

Nibe

Nibe F135 Bedienungsanleitung

Zephyr

Zephyr Spruce AK9834BS Installationsanleitung

Kuppersberg

Kuppersberg INTRO 60 Montage- und Wartungsanleitung

Hisense

Hisense MH6INBG Bedienungsanleitung

Miele

Miele DA 1255 Bedienungsanleitung

Broan

Broan 46000 Bedienungsanleitung

GE Profile PV977 Originalbetriebsanleitung

FALMEC

FALMEC FFRIA24W5FS Bedienungsanleitung

Whirlpool

Whirlpool RH2600XL-1 SERIES Bedienungsanleitung

ETNA

ETNA AV360RVS Bedienungsanleitung

JUNO

JUNO JDF603E6 Bedienungsanleitung

Miele

Miele DA 6708 D Bedienungsanleitung

Tricity Bendix

Tricity Bendix LE 150 Handbuch

AEG

AEG X68163BV1 Bedienungsanleitung

AEG

AEG 125 D Bedienungsanleitung

Smeg

Smeg KSEV97X Bedienungsanleitung

Nibe

Nibe S Series Benutzerhandbuch