Sirius Satellite Radio STL969 Bedienungs- und Wartungshandbuch

SLT969 ceiling cassette user manual

INSTALLATION AND USE INSTRUCTIONS

Congratulations on your purchase!

Thank you for choosing a Sirius product.

SLT969 EAN #9351116002077

SLT969 WH EAN #9351116002084

The symbol on the product or on its packaging indicates that this product

may not be treated as house-hold waste. Instead it shall be handed

over to the applicable collection point for the recycling of electrical and

electronic equipment. By ensuring this product is disposed of correctly,

you will help prevent potential negative consequences for the environment

and human health, which could otherwise be caused by inappropriate

waste handling of this product. For more detailed information about

recycling of this product, please contact your local city office, your

household waste disposal service or the shop where you purchased the

product. This appliance is marked according to the European directive

2002/96/EC on waste electrical and electronic equipment (WEEE).

BEFORE YOU INSTALL

TO THE ATTENTION OF THE USER

PRE-INSTALLATION CHECKS

OPENING THE GLASS PANEL

INSTALLATION

DUCTING THE CASSETTE

REMOTE CONTROL

WIRING DIAGRAM

WARRANTY

BEFORE YOU INSTALL – please read

Sirius warranty covers only Sirius product. If you choose to install a non-Sirius branded accessory

such as flexible ducting, Sirius will only warrant the hood and motor. If installation is found to be the

cause of failure or issue then charges will apply for service and parts.

Flexible ducting is not permitted under any circumstances. Flexible ducting has been found to

increase noise levels, increase vibration and reduce airflow.

Sirius Semi-rigid or solid ducting can be used in lieu.

There is a range available to suit any application.

Ducting available at www.siriusbrand.com

A reduction in the duct diameter from stated ducting size will void warranty.

If you are in doubt about the ducting, please contact Sirius on 1300 762 219 prior to installation

CAUTION

WARNING

The appliance must be installed and

connected to the power supply only by a

qualified technician.

• There shall be adequate ventilation of the room when the range hood is used at the same time as

appliancess burning gas or other fuels (not applicable to appliances that only discharge the air back into

the room)

• The details concerning the method and frequency of cleaning

• There is a fire risk if cleaning is not carried out in accordance with the instructions;

• Do not flambé under the range hood;

• CAUTION: Accessible parts may become hot when used with cooking appliances.

TO THE ATTENTION OF THE USER

This rangehood is designed to work with ducted

outside evacuation.

Keep these instructions for use with the appliance. If

the appliance should be sold or passed on to others,

make sure that the instructions are passed on with

it. We thank you for taking note of these suggestions

before installing and using the appliance. They have

been written for your personal safety and the safety

of others.

SAFETY INSTRUCTIONS

These hoods have been designed for personal

use in the home. The appliance must be used by

adults. Make sure that the appliance is out of reach

of children and that they do not use it to play with.

Make sure that children do not operate the controls.

• When the appliance is delivered, check the overall

appearance of the packaging. Check PARTS

LIST on page 20 for all included parts prior

to discarding packaging.

Any remarks should be written on the delivery

coupon, of which you keep a copy.

Your appliance is designed for normal domestic

use. It is not designed for commercial or industrial

use, or for purposes other than those for which it

was designed.

• Any consequences of or damage from incorrect

installation or incorrect use of the appliance will

not be covered by the manufacturer’s guarantee.

• Do not ever change or try to change the

characteristics of this appliance. This would be

a danger. Repairs must be performed only by an

authorised technician.

• Always disconnect the hood before carrying out

cleaning or maintenance operations.

• Adequately ventilate the room when a rangehood

and other appliances, powered by energy other

than electricity, are used simultaneously, so that

the hood does not suck any combustion fumes.

• It is not allowed to cook food over open flames

(flambé) or operate gas hobs without pots

or pans on them under the hood itself (the

flames sucked into the hood might damage the

appliance).

• Frying under the appliance must be done under

constant supervision as hot oils and fats may

ignite.

• Respect the guidelines for cleaning and

replacement of grease filters. Accumulated

deposits of grease are a fire hazard.

WARNING

• This appliance must not be used over cook tops

cook tops with power levels that could damage

the appliance.

• Never use steam or high-pressure devices

for cleaning your hood (regulations regarding

electrical safety).

• Never use the rangehood without the grease

filters.

At Sirius, we are constantly seeking to improve

our products. We reserve the right to modify their

technical, functional, or aesthetic characteristics

deriving from their upgrading.

Motors manufactured and approved by Sirius only

are to be used at all times. Failure to comply with this

will result in the forfeit of the manufacturer warranty.

The air collected must not be conveyed into a flue

used for smoke or fumes from appliances powered

by anything other than electricity (central heating

systems, bathroom and toilet exhausts, etc.). As

far as discharging exhaust air is concerned, please

follow the guidelines given by competent authorities.

PRE-INSTALLATION CHECKS

Connect all of the electrical components to the unit and motor to make sure both the unit and the motor are

functioning properly.

(NOTE: The motor plug is fitted with a dummy plug - with the exception of SEM1 motor - to protect

the connection from dust. Ensure the red dummy plug is removed and replaced with the two

pin motor plug from the power transformer box. Failure to do so will result in only two speeds

operating).

Remove all plugs and proceed with installation if both unit and motor are fully operational.

BEFORE YOU INSTALL

Lighting connection

Installation must comply with the regulations in force regarding the ventilation of enclosed environments.

In particular, discharged air must not be conveyed into a duct used for fumes discharge or discharge from

appliances using gas or other combustible materials. Air cannot be ducted into roof space.

The use of discontinued ducts is not allowed without the approval of a qualified technician.

Sirius warranty covers only Sirius product. If you choose to install a non-Sirius branded accessory such as

flexible ducting, Sirius will only warrant the hood and motor. If installation is found to be the cause of failure or

issue then charges will apply for service and parts.

Flexible ducting is not permitted under any circumstances. Flexible ducting has been found to increase noise

levels, increase vibration and reduce airflow. Sirius Semi-rigid or solid ducting can be used in lieu. There is a

range available to suit any application.

Available at www.siriusbrand.com

A reduction in the duct diameter from stated ducting size will void warranty.

If you are in doubt about the ducting, please contact Sirius on 1300 762 219 prior to

installation.

CAUTION

Before proceeding with the installation of the ceiling cassette, please thoroughly inspect the entire unit

(including the motor) for any damages, including all of the electrical connections. If any damage is found, cease

installation and report it immediately to the retail partner that the cassette was purchased from.

Reduction of the ducting diametrer will void the manufacturer warranty as it will severely affect the performance

of the motor and may cause damage with prolonged usage.

Use ducting approved by standards enforced, see www.siriusbrand.com for details for approved ducting.

The manufacturer will not be deemed responsible for air capacity and noise problems caused by failure to

comply with the above and no warranty on the product will be provided.

FAILURE TO INSTALL THE SCREWS OR FIXING DEVICE IN

ACCORDANCE WITH THESE INSTRUCTIONS MAY RESULT IN

ELECTRICAL HAZARDS OR ELECTROCUTION.

The cassette requires one 10AMP GPO located inside the ceiling cavity

to power both the lighting and the motor.

The ceiling cassette is designed for a ceiling height of up to 2700mm high.

• Only use Sirius Ducting with a maximum length of 7 metres; from the outlet collar on the cassette to the

exit point.

• Limit the number of elbows in the ducting, since each 90 degree bend reduces the air capacity by 1 lineal

metre (e.g. if there are 2 x 90 degree bends, the maximum duct length should not exceed 5 metres.)

• Avoid abrupt changes of direction where possible, bends of more than 90 degrees should be avoided at all

costs.

• The ducting applicable for this cassetteis 220mm x 90mm rectangular Sirius Ducting and can be

purchased through the retailer where the cassette was purchased, or visit www.siriusbrand.com.

The ducting can be transitioned from rectanguar to round if desired.

WARNING

NOTE

DANGER

On the side where the speed control light is visible,

plull down the centre of the panel. This panel is held

on by a strong magnet. Allow the panel to swing

open to expose the grease filters. (Fig. 1)

After swinging open the panel, disconnect the

lighting by depressing the tabs on the connection

and pulling on the cable.

To ensure that no damage is caused during

the installation process, remove the panels by

unscrewing the hinges on the underside of the

cassette.

This will also lighten the Cassette to make lifting it

into place and installation easier. (Fig. 2)

OPENING THE GLASS PANELS - SLT969

Panel drops down

Fig. 1

Fig. 2

As every installation will differ slightly depending on the ceiling cavity of the dwelling, this

installation instruction shall be used as a guide only.

INSTALLATION

NOTE

1. Horizontal support beams need to be installed in the cavity above to support the weight of the cassette.

(Fig 3.)

2. Attach the bottom half of the mounting brackets to the Cassette (Fig. 4) by using the supplied

6 x 20mm threaded screws and screwing them in from the inside of the cassette in the specified location.

(Fig. 5)

Timber support beams (not supplied)

Fig. 3

Fig. 4 Fig. 5

3 fixing points

either side.

DUCTING THE CASSETTE

3. Fix the top section of the mounting brackets to

the horizontal support beams in the ceiling, taking

measurements to make sure theu are aligned with

the brackets already attached to the cassette.

4. Lift the cassette to the desired height and fix in

place with the use of the 10mm supplied screws

that are inserted on the sides of the mounting

brackets. (Fig. 6)

1. Part ‘A’ will come fitted to the short side of the cassette from the factory. If either of the long side options

are required, remove Part ‘A’ from the short side by removing the 4 x 10mm screws holding it in place.

Unscrew the 4 x 10mm screws from the long side and remove the blocking plate, Part ‘A’ in its place and use

the blocking plate to cover the gap on the short side.

2. Connect Part ‘B’ to Part ‘A’ and fix in place with

duct tape to ensure a tight seal. Do not use screws

as this can cause a whistling noise once the motor

is switched on.

3. Connect part ‘C’ (needs to be purchased

separately and does not come included in the

packaging with the cassette) to Part ‘B’.

4. Connect part ‘D’ (needs to be purchased

separately and does not come included in the

packaging with the cassette) to Part ‘C’.

5. If additional lenghts of ducting are needed to get

to the exit point, use another Part ‘C’ and another

Part ‘D’.

Fig. 6

Part ‘A’

Part ‘C’

Part ‘B’

Part ‘D’

Fig. 7

SPS-66102291000 (PART ‘D’)

RECTANGULAR DUCTING

220x90mm (opening)

1200mm (length)

SPS-66102291000 (PART ‘C’)

RECTANGULAR CONNECTOR

220x90mm (opening)

44mm (length)

(PART ‘B’)

(PART ‘A’)

Working:

6 channel control for rangehood remote.

• When the rangehood is first turned on, hold the

lighting button for 5 seconds.

RC001 - RADIO CONTROL

Radio control used for the remote operation of

rangehoods.

TECHNICAL DATA

• Alkaline battery powered: 12 V mod. 23 A

• Operating frequency: 433.92 Mhz

• Combinations: 32.768

• Max. consumption: 25 mA

• Operating temperature: -20 ÷ + 55 °C

• Dimensions: 120 x 45 x 15 mm.

OPERATING DESCRIPTION

The transmitter is equipped with 5 buttons for cooker

hood management, as specified below:

: Light ON/OFF command.

: Motor ON (speed level 1) / OFF command.

: Reduce speed.

: Increase speed.

: 10-minute timer.

INITIAL OPERATING CONDITION

The manufacturer supplies the radio control unit

ready to be used with codes preset in the factory.

REMOTE CONTROL OPERATION MODE

Standard configuration:

Standard configuration requires all rangehood radio

control systems to be provided with the same

transmission code. In the event two rangehoods are

installed in the same room or nearby, each system

may affect the operation of the another. Therefore,

the code of one radio control system must be

changed.

Generating a new transmission code:

The radio control system is provided with preset

codes. Should new codes be required, proceed as

follows: Press simultaneously buttons:

for two seconds. When LEDs are on, press buttons:

(within 5 seconds). The LEDs flashing 3 times

indicate the procedure is completed.

WARNING! This operation deletes permanently

the preset codes.

Learning the new transmission code.

Once the transmission code is changed in the radio

control unit, the electronic central unit of the cooker

hood must be made to set the new code in the

following way:

Press the main power-off button of the hood and

then restore power to the electronic control unit.

Within the next 15 seconds, press the Light Button to

synchronise the central unit with the code.

Reset of the Factory configuration:

To restore the Factory configuration, follow the

procedure described below: press simultaneously

buttons:

for 2 seconds. When LEDs light on, press buttons:

(within 5 seconds). LEDs flashing 6 times in-dicate

the procedure is completed.

WARNING! This operation deletes permanently

the preset codes.

Emergency button:

In the event that the radio control does not work, use

the emergency button to switch the appliance off.

After any necessary repairs have been performed,

reset the emergency button.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Sirius Satellite Radio Dunstabzugshaube Handbücher

Sirius Satellite Radio

Sirius Satellite Radio SLT968 Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio Downdraft S-DD18 Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SLT972 Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SLT955 Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SILT-28 Series Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SLT976 Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SM927 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SILT-21 B Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio ALFRESCO SL83 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SLT950 EM Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SLT962 Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SLTC EM 107 G900 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SL906EM-L 520 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SIU3 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SL906 L 1500 Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio UP right Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SLT960 Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SU906 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio S-DD2-L EMIC 880 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SUTC92 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio Valentina SLT958EM Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SL85 Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SL85 Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SDD2EMIX60 Bedienungsanleitung

Beliebte Dunstabzugshaube Handbücher anderer Marken

emmeti

emmeti RECUPA MED A-140 Leitfaden

Nibe

Nibe F135 Bedienungsanleitung

Zephyr

Zephyr Spruce AK9834BS Installationsanleitung

Kuppersberg

Kuppersberg INTRO 60 Montage- und Wartungsanleitung

Hisense

Hisense MH6INBG Bedienungsanleitung

Miele

Miele DA 1255 Bedienungsanleitung

Broan

Broan 46000 Bedienungsanleitung

GE Profile PV977 Originalbetriebsanleitung

FALMEC

FALMEC FFRIA24W5FS Bedienungsanleitung

Whirlpool

Whirlpool RH2600XL-1 SERIES Bedienungsanleitung

ETNA

ETNA AV360RVS Bedienungsanleitung

JUNO

JUNO JDF603E6 Bedienungsanleitung

Miele

Miele DA 6708 D Bedienungsanleitung

Tricity Bendix

Tricity Bendix LE 150 Handbuch

AEG

AEG X68163BV1 Bedienungsanleitung

AEG

AEG 125 D Bedienungsanleitung

Smeg

Smeg KSEV97X Bedienungsanleitung

Nibe

Nibe S Series Benutzerhandbuch