Sirius Satellite Radio SILT-26 Series Bedienungsanleitung

SILT-26

PENDANT RANGEHOOD INSTALLATION INSTRUCTIONS

Congratulations on your purchase!

Thank you for choosing a Sirius product.

SILT-26 B EAN #9351116002428

SILT-26 C EAN #9351116001308

SILT-26 G EAN #9351116001322

SILT-26 W EAN #9351116001315

www.siriusbrand.com

DEAR CUSTOMER

The rangehood is intended for household use only. Materials used for packaging are nature friendly and may

be recycled, deposited or destroyed without any threat to the environment.

In order to recognize these features, all packing materials are marked with relevant symbols.

When you plan to replace your rangehood, deposit your old appliance with the authorized depot dealing with

used household appliances.

INSTALLATION

Instructions for use have been prepared for the user, and describe the particulars and handling of the

appliance. These instructions apply to different models from the same family of appliances, therefore you may

find information and descriptions that may not apply to your particular appliance.

INSTALLATION INSTRUCTIONS

He appliance should be connected to the power supply in accordance with the instructions from the chapter

“Electrical connections” and in line with the standing regulations and standards. The connections should be

carried out by a qualified personnel only.

FIRE HAZARD PROTECTION

Appliances are allowed to be mounted on one side next to a high kitchen cabinet, the height of which may

exceed that of the appliance. On the opposite side however, only a kitchen cabinet of equal height as the

appliance is allowed.

The symbol on the product or on its packaging indicates that this product

may not be treated as household waste. Instead it shall be handed

over to the applicable collection point for the recycling of electrical and

electronic equipment. By ensuring this product is disposed of correctly,

you will help prevent potential negative consequences for the environment

and human health, which could otherwise be caused by inappropriate

waste handling of this product. For more detailed information about

recycling of this product, please contact your local city office, your

household waste disposal service or the shop where you purchased the

product. This appliance is marked according to the European directive

2002/96/EC on waste electrical and electronic equipment (WEEE).

The cooker surface and the lowest part of the hood

must be at a minimum distance, as shown above.

• The appliance is not intended for use by young

children without supervision. Young children

should be supervised to ensure they do not play

with the appliance.

• When performing the electrical connections on

the appliance, please make sure that the current-

tap is provided with earth connection and that

voltage values correspond to those indicated on

the label placed inside the appliance itself.

• Please disconnect the appliance from power

mains, before carrying out any cleaning or

maintenance operation. If the appliance is not

equipped with a nonseparable flexible cable and

plug, or with another device ensuring omnipolar

disconnection from the mains, with an opening

distance between the contacts of at least 3mm,

then such disconnecting devices must be

provided in the fixed installation. If the appliance

is equipped with a power cord and a plug, it shall

be placed in such a way that the plug can be

reached easily.

• The appliance can be arranged only for filtering

performances. In its filtering version the air and

fumes conveyed by the appliance are cleaned

both by a grease filter and by an active carbon

filter, and put again into circulation. While the

lamp version (SILT26 LAMP) only allows for hob

lighting.

• The use of materials which can burst into flames

(flambé) should be avoided in close proximity of

the appliance. When frying, please pay particular

attention to fire risk due to oil and grease. Being

highly flammable, hot oil is especially dangerous.

Do not use uncovered electric grills. In order to

avoid possible fire risk, all instructions for grease-

filter cleaning and for removing eventual grease

deposits should be strictly followed.

• Two persons are needed for the installation of this

product.

(Fig. 2)

600 - 700mm (induction)

650 - 750mm (gas)

WARNING

The appliance must be installed and

connected to the power supply only by a

qualified technician.

TECHNICAL DATA

• Voltage rating: 230 - 240V

• 50Hz

• There shall be adequate ventilation of the room when the range hood is used at the same time as

appliancess burning gas or other fuels (not applicable to appliances that only discharge the air back into

the room)

• The details concerning the method and frequency of cleaning

• There is a fire risk if cleaning is not carried out in accordance with the instructions;

• Do not flambé under the range hood;

• CAUTION: Accessible parts may become hot when used with cooking appliances.

WARNING: Failure to install the screws or fixing

device in accordance with these instructions

may result in electrical hazards.

At the beginning make sure that the package is intact

and all the parts are unbroken, otherwise stop the

installation and contact the dealer.

The manufacturer is not responsible for

damages caused by material handling or

product installation.

Before installing the appliance read all these

instructions carefully.

WARNING: This product is made of ceramics,

for that reason it requires an appropriate and

accurate handling, as well as a professional and

accurate installation.

Extract the product from the packaging and lay it on

a suitable place, a soft material such as sponge or

fabric should be used to place the product on it.

By using the supplied drilling jig, perforate the wall

according to the four pattern indicated by the jig

itself. The center of the drilling jig should correspond

to the center of the cooktop. Insert the supplied

dowel into the holes made, tighten them, but do not

tighten until they are flush; the three screws into the

dowels corresponding to the holes with discharge

head (Fig.8 A) leaving the hole for the locking screw

empty (Fig. 9 B) because it will be added later.

EXPLODED VIEW

USES INSTALLATION

(Fig. 8)

(Fig. 9)

A: Mounting bracket

B: Ceramic plate cover

C: Rangehood body

D: Motor, light, and filter

The appliance can be arranged only for filtering

performances. In its filtering version the air and fumes

conveyed by the appliance are cleaned both by a

grease filter and by an active carbon filter, and put

again into circulation.

WARNING: Failure to install the screws or fixing

device in accordance with these instructions

may result in electrical hazards.

Place the ceramic cover over the motor components

and insert the steel cables into the three holes of the

ceramic, as shown in the figure (Fig. 1).

Put the power cable through the air outlet grill, see

Figure 2. The ceramic part must perfectly cover the

metal part named “D” in the exploded view.

Extract from the packaging the ceramic cover for the

ceiling plate (see the detail B on the exploded view),

place the cover over the hood and put the steel

cables through the three holes in the ceramic body,

the power cable should be put through the central

hole of the ceramic, see Fig.3.

Take the metal plate from the packaging and then put

the steel cables through the appropriate supports, as

shown in Fig. 4.

Adjust the height of the rangehood by scrolling the

steel cables up and down inside the support. You

need to unscrew and push the support in order to

allow the scrolling of the cable, see Fig. 5.

Check that the remaining length of steel cables from

the supports indicated in Fig.6 is the same, in order

to ensure that it will be installed perfectly parallel to

the ceiling. Tightening the appropriate support by

screwing it as shown in Fig.6, block the steel cables.

Add the clips as a further safety precaution for cable

blocking Fig. 7.

(Fig. 1)

(Fig. 4)

(Fig. 5)

(Fig. 6)

(Fig. 2)

(Fig. 3)

(Fig. 7)

Put the hood near the ceiling and hook the plate to

the screws previously installed (fig.8 A) Tighten

the three screws fixing the plate to the ceiling,

then block the hood definitively adding the security

screw, see fig.9 B. Connect the appliance to the

electric grid.

Lift up the ceramic cover until reaching the ceiling

(fig.10 ), make sure that the springs have hooked the

ceramic cover.

In case the ceramic cover of the body, is not perfectly

flat or parallel to the body, it is possible to make an

adjustment after installation. Remove the grease filter

as described in Maintenance Section, remove the

three plastic caps shown in Figure 13 A.

Using a Phillips screw head screwdriver, tighten or

loosen the three screws in order to raise or lower the

ceramic body on a specific side (fig. 14). After the

adjustment insert the rubber tips and the grease filter

again.

(Fig. 10)

(Fig. 13)

(Fig. 14)

Remote control

6 channel control for rangehood remote.

• When the rangehood is first turned on, hold the

lighting button for 5 seconds.

RC001 - RADIO CONTROL

Radio control used for the remote operation of

rangehoods.

TECHNICAL DATA

• Alkaline battery powered: 12 V mod. 23 A

• Operating frequency: 433.92 Mhz

• Combinations: 32.768

• Max. consumption: 25 mA

• Operating temperature: -20 ÷ + 55 °C

• Dimensions: 120 x 45 x 15 mm.

OPERATING DESCRIPTION

The transmitter is equipped with 5 buttons for cooker

hood management, as specified below:

: Light ON/OFF command.

: Motor ON (speed level 1) / OFF command.

: Reduce speed.

: Increase speed.

: 10-minute timer.

INITIAL OPERATING CONDITION

The manufacturer supplies the radio control unit

ready to be used with codes preset in the factory.

WORKING OPERATION MODE

Standard configuration:

Standard configuration requires all rangehood radio

control systems to be provided with the same

transmission code. In the event two rangehoods are

installed in the same room or nearby, each system

may affect the operation of the another. Therefore,

the code of one radio control system must be

changed.

Generating a new transmission code:

The radio control system is provided with preset

codes. Should new codes be required, proceed as

follows: Press simultaneously buttons:

for two seconds. When LEDs are on, press buttons:

(within 5 seconds). The LEDs flashing 3 times

indicate the procedure is completed.

WARNING! This operation deletes permanently

the preset codes.

Learning the new transmission code.

Once the transmission code is changed in the radio

control unit, the electronic central unit of the cooker

hood must be made to set the new code in the

following way:

Press the main power-off button of the hood and

then restore power to the electronic control unit.

Within the next 15 seconds, press the Light Button to

synchronise the central unit with the code.

Reset of the Factory configuration:

To restore the Factory configuration, follow the

procedure described below: press simultaneously

buttons:

for 2 seconds. When LEDs light on, press buttons:

(within 5 seconds). LEDs flashing 6 times in-dicate

the procedure is completed.

WARNING! This operation deletes permanently

the preset codes.

Emergency button:

In the event that the radio control does not work, use

the emergency button to switch the appliance off.

After any necessary repairs have been performed,

reset the emergency button.

TIMING

As a result of the new EU65 “Energy label” and EU66

“ Ecodesign” regulations issued by the European

Commission, which came into force as from January

1st, 2015 , our products have been adapted to

comply with these new requirements.

All of the models complying with the energy label

requirements, are equipped with new electronics

including a timer device for suction speeds control,

when the air capacity exceeds 650m³/h.

Internal motor models, with maximum air capacity

higher than 650m³/h, are equipped with a timer

device that automatically switches the suction speed

from 4th to 3rd speed, after 5 minutes operation.

External motor models are equipped with remote

motors that , as for internal motor versions, include

a timer device that switches down the suction speed

when it exceeds 650m3/h. (See External Motors

Instructions ). Remote motors, whose air capacity

exceeds 650m³/h at both 4th and 3rd speed, will

have the following by default timer control functions:

The suction speed is automatically switched from 4th

to 2nd speed, after 6 minutes operation.

If the appliance is working at 3rd speed, it is

automatically switched to 2nd speed, after 7 minutes

operation. Operation speeds can also be changed

during operation.

The energy consumption of the appliance in standby

mode is lower than 0.5W.

MAINTENANCE

An accurate maintenance guarantees good

functioning and longlasting performance. *Particular

care is due to the grease filter The grease filter is

fixed through magnets, therefore it is sufficient to

insert a hand tool or the tip of a knife in the dedicated

opening and push upwards in order to pull the filter

out of its place. See Fig. 12. In order to remove the

filter from the hood, unhook the two security cables

opening their snap-hooks, The active coal filter has

to be removed after the extraction of the grease filter

by pushing its special plastic handle. The grease filter

can be cleaned by hand-washing or in dishwashers.

The active coal filter has to be replaced in relation to

its use, at least once every six months. To clean the

appliance itself tepid wa-ter and neutral detergent are

recommended, while abrasive products should be

avoided.

The power cord must be replaced only by qualified

person.

The LED lamps must be replaced only by qualified

person.

(Fig. 14)

WORKING

Andere Handbücher für SILT-26 Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Sirius Satellite Radio Dunstabzugshaube Handbücher

Sirius Satellite Radio

Sirius Satellite Radio SUF1 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SM923 520 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SLT950 EM Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SLT105 Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SU35 TC Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SUTC92 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SU1 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SU906 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SU900 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SILT18 Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SUT958 H200 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SU909 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio ALFRESCO SLEM80 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SL926DLTM Series Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio Valentina SLT977EMEL Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SILT-28 Series Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SLTC93 Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SLEM83 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SL906 L 1500 Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SDD2ELEMTC Series Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SU-DD20 Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SLT960 Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio Downdraft S-DD18 Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio 9351116001063 Bedienungsanleitung

Beliebte Dunstabzugshaube Handbücher anderer Marken

emmeti

emmeti RECUPA MED A-140 Leitfaden

Nibe

Nibe F135 Bedienungsanleitung

Zephyr

Zephyr Spruce AK9834BS Installationsanleitung

Kuppersberg

Kuppersberg INTRO 60 Montage- und Wartungsanleitung

Hisense

Hisense MH6INBG Bedienungsanleitung

Miele

Miele DA 1255 Bedienungsanleitung

Broan

Broan 46000 Bedienungsanleitung

GE Profile PV977 Originalbetriebsanleitung

FALMEC

FALMEC FFRIA24W5FS Bedienungsanleitung

Whirlpool

Whirlpool RH2600XL-1 SERIES Bedienungsanleitung

ETNA

ETNA AV360RVS Bedienungsanleitung

JUNO

JUNO JDF603E6 Bedienungsanleitung

Miele

Miele DA 6708 D Bedienungsanleitung

Tricity Bendix

Tricity Bendix LE 150 Handbuch

AEG

AEG X68163BV1 Bedienungsanleitung

AEG

AEG 125 D Bedienungsanleitung

Smeg

Smeg KSEV97X Bedienungsanleitung

Nibe

Nibe S Series Benutzerhandbuch