SKYTRONIC 351.124 Bedienungsanleitung

UserManual

DVR

Digital Video Recorder

HANDLEIDING

USER’S MANUAL

ANLEITUNG

351.124

UserManual

Chapter 1: DVR Features

DVR Feature

zMPEG4 compression

z4-Channel: 4 BNC Camera Inputs - 2 BNC Video Outputs

9-Channel: 9 BNC Camera Inputs - 1 BNC Video Output

z4-Channel: 2 Audio Inputs - 2 Audio Outputs

9-Channel: 1 Audio Input -1 Audio Output

zSystem Format : NTSC /PAL

zMotion Detection with Sensitivity and Area Settings

zTime Schedule, Alarm and Motion Triggered Recording Modes

zHard Disk Support up to 500GB

zSupport PTZ Control via 485 Port

zView and Operate over Network (Broadband Connection Required)

zBuilt-in USB2.0 Port for Backup to Computer or

USB Memory stick Backup (Optional)

zVGA Output (Optional)

Chapter 2: Overview

2.1 Front Panel (All Modes)

1. Power switch

2. Removable HDD Tray

3. HDD Lock

4. USB 2.0 Interface

5. Rewind

6. Pause

7. Play

8. Fast Forward

9. Stop

10. Record

11. CH1

12. CH2

13. CH3

14. CH4

15-19. CH5-CH9

(9CH DVR Only)

20. Mute Audio

21. Display All Cameras

22. Menu/Exit Menu

23. IR Receiver

24. Up Arrow

25. Select

26. Left Arrow

27. Down Arrow

28. Right Arrow

29. Power Indicator

30. HDD Indicator

UserManual

2.2 Rear Panel

1. Audio Input(s)

2. Video output(s)

3. CH4

4. CH3

5. CH2

6. CH1

7. VGA output (Optional)

8. LAN

9. Audio Output

10. CH9

11. CH8

12. CH7

13. CH6

14. CH5

15. RS485/Sensor

Input/Alarm Output

16. DC Power Input Jack

2.3 Remote Control

1-9 Channel Select 1-9

0 Number

ALL Display all Channels

Menu Enter or Exit Menu

▲Move Up/Left

▼Move Down/Right

SEL Select /Modify Item

Rewind

Play Recording

Fast Forward

●Record

Pause

■Stop Recording/Playback

Audio Audio Input/Output

Mute Mute Audio

UserManual

Chapter 3: Installation

3.1 Install Hard Disk

NOTICE: Don’t take out HDD when DVR is running.

Make sure the HDD is set to be MASTER according to the hard drive manual.

I. If your product comes with a removable HDD drawer (optional), please refer below:

(1) Take out the hard drive drawer from the DVR side panel，Connect the power cord and data cable to hard disk;

(2) Put the hard drive drawer back into the DVR (Make sure the drawer is firmly inserted to the DVR) and then

lock the hard drive drawer.

II. If your product does not come with a removable HDD drawer, please refer below:

(1) Remove the screws around the top cover;

(2) Remove the top cover carefully;

(3) Connect the power cord and data cable to hard disk carefully;

(4) Use the provided screws to fix hard disk on the rack inside and then replace the top cover of the case.

3.2 Connecting Camera and Monitor

There are 4/9 camera inputs and 2/1 Monitor outputs with BNC connectors (Refer to 2.2 Rear Panel).

3.3 VGA Output (optional)

There is 1 CRT or LCD monitor output with VGA port.

3.4 Connecting Power Supply

Please only use the power adapter supplied with the DVR.

UserManual

Chapter 4: Starting the DVR

5.1 Firmware Version

5.2 Detecting Installed Hard Drive

5.3 Format Hard Drive

DVR will detect the installed hard drive

and display the hard drive information.

When the DVR detects a new hard drive,

you will be prompted to format the hard drive

before using the DVR.

Press [SEL] to format or press [MENU]

to cancel.

After connecting the power adapter

and turning on the power button, the system

will boot-up and display the version and

released date of the DVR firmware.

UserManual

Chapter 5: DVR Menu System

5.1 Navigating the Menus

5.2 Menu Overview

MenuDirectory

Camera Setup

Record Setup

Record Frame rate

Video Quality

Record Schedule

Sensor Setup

Hard Drive Setup

Miscellaneous Setup

Network Setup

Language

Video Backup

Reset Menu

[MENU]: enters Main Menu

[▲, ▼, ◄and ►]: move the cursor

[SEL]: select/modify settings

[MENU]: press again to exit or go

back to previous menu.

Main Menu

Change Password

Set Time

Hidden Channel

Audio Port Setup

PTZ Setup

Image Parameters

Password Enable

Keypad Tones

VGA Setup

When the DVR detects a new hard drive,

you will be prompted to format the hard drive

before using the DVR.

Press [SEL] to format or press [MENU] to

cancel.

UserManual

5.3 Camera Setup

NoteIf a camera channel is set to OFF will not record(Refer to 6.4 Record Setup)

5.4 Record Setup

5.5 Record Frame rate

Press [▲, ▼, ◄or ►] button to select a channel, and then press [SEL] to

increase the value or press [■STOP] to reduce the value.

Note: Higher frame rate shows smooth images but requires more hard drive

space.

Camera Setup allows you to turn

cameras on or off.

Press [▲, ▼, ◄and ►]button to

select a channel and then press [SEL] to

modify the setting ON or OFF.

The total frame rate is 50fps (PAL) or

60fps (NTSC). You can set the frame rate

for the channel which you selected to

record. If the sum of the frame rate you

select for all cameras is more than 50fps

(PAL)/60fps(NTSC), the DVR will

automatically adjust the largest frame rate

value to a smaller value.

Record Setup allows you to set up

recording channels.

Press [▲, ▼, ◄and ►]button to

select a channel, and then press [SEL] to

modify the setting to ON or OFF.

If a channel is disabled in Camera

Setup, it will not record and the DVR will

display “NOCAM” on screen.

UserManual

5.6 Video Quality

5.7 Record Schedule

Setting the Record Schedule allows you to customize the type of recording

depending on the time of day.

NO-RECORD [ white]: DVR will not record during the time.

NORMAL-RECORD [ red]: DVR will record continuously.

SENSOR-RECORD [S]: DVR will record when sensor or motion is triggered.

NOTE: In order to activate the record schedule press the []record button when

viewing the cameras. After pressing the []record button if schedule is set to

“NORMAL-RECORD” the DVR will start to record immediately; if the schedule is

set to be “SENSOR-RECORD” the DVR will not start recording until a motion is

detected by the DVR or an installed sensor is triggered.

Video Quality has 4 different settings:

Highest, High, Normal and Low.

The higher the video setting, the

better quality images, however higher

quality images require more hard drive

space.

Press [SEL] to change the quality

setting.

The time line indicates 24 hours of a

day based on AM/PM (0 = 12).

Press [▲, ▼, ◄or ►] button to

select a time point, press [SEL] to modify

the recording mode.

UserManual

5.8 Sensor Setup

CONT: Continuous alarm until any key is pressed..

OFF: No alarm

5.9 H/W Sensor Setup

Note: Sensors and extension alarm are not included with the DVR systemand

may be purchased separately.

Note: For 4CH DVR, there are 4CH Inputs of the Sensor;

For 9CH DVR, there are 8CH Inputs of the Sensor.

5.10 Motion Detector Setup

This section allows you to set up motion detection options for each camera.

Sensor Record Time indicates

how long the recording time is

when the motion or sensor is

triggered.

Alarm On Time indicates

whether the buzzer will sound

when motion is detected.

HARDWARE SENSOR SETUP:

There are 3 different modes for sensor setting:

NOT INSTALLED, NORMAL-CLOSE and

NORMAL-OPEN. Consult the alarm

purchased for more details on which setting is

required.

MOTION DETECTOR SETUP:

ON/OFF: Enable or disable motion detection

recording.

LEVEL: Sensitivity for motion detection.

There are 3 levels sensitivity: Level 1-low,

3- highest

AREA: Select detectable area on the screen.

UserManual

5.11 Hard Drive Setup

This section will display the current hard drive status and usage options

HDD SIZE: indicates the total capacity of the hard drive installed in the DVR.

HDD USED:indicates the space used in the hard disk drive for recording and the

percent used.

HDD FORMAT: will erase all video and data on the installed hard drive and make it

readable by the DVR

Note: You will be prompted for the password when formatting a hard drive. The

default password is “111111”

Area Selection:

Press [▲, ▼, ◄or ►] button to

select a block, and press [SEL] button to set

the block to detect motion. The area is

detectable when it is clear, the area is not

detectable when it is covert by shadow.

OVERWRITE ENABLED:

ON: overwrite oldest video when hard

drive is full.

OFF: stop recording when hard drive

is full.

Inhaltsverzeichnis

Sprachen:

Andere SKYTRONIC DVR Handbücher

SKYTRONIC

SKYTRONIC 351.158 Bedienungsanleitung

SKYTRONIC

SKYTRONIC 351.136 Bedienungsanleitung

SKYTRONIC

SKYTRONIC 351.180 Bedienungsanleitung

SKYTRONIC

SKYTRONIC 351.157 Bedienungsanleitung

SKYTRONIC

SKYTRONIC 351.158 Bedienungsanleitung

SKYTRONIC

SKYTRONIC 351.174 Bedienungsanleitung

SKYTRONIC

SKYTRONIC 351.174 Bedienungsanleitung

SKYTRONIC

SKYTRONIC DVR Bedienungsanleitung

SKYTRONIC

SKYTRONIC 351.142 Bedienungsanleitung

SKYTRONIC

SKYTRONIC 351.154 Bedienungsanleitung

SKYTRONIC

SKYTRONIC 351.154 Bedienungsanleitung

Beliebte DVR Handbücher anderer Marken

FLIR

FLIR M3100E Series Bedienungsanleitung

VTRACKPRO

VTRACKPRO FPRO300 Bedienungsanleitung

Swann

Swann NVR-7085 models Bedienungsanleitung

XtendLan

XtendLan DVR-1670C Bedienungsanleitung

urmet domus

urmet domus 1093/004AHD Bedienungsanleitung

Holux

Holux M1 Bedienungsanleitung

CMOS DOTCOM

CMOS DOTCOM ANX-1670 Bedienungsanleitung

Whistler

Whistler D16VRS Bedienungsanleitung

Defender Security

Defender Security 82-20235 Bedienungsanleitung

MISUMI

MISUMI MP-WF100M Bedienungsanleitung

Speco

Speco D8HU Bedienungsanleitung

UST

UST DDR-E04AA Gebrauchsanweisung

Consolidated

Consolidated Digital Video Recorder Bedienungsanleitung

Mace

Mace DVR0404RW Kurzanleitung

RCA

RCA RTD315W Bedienungsanleitung

Hauppauge

Hauppauge HD PVR 2 Bedienungsanleitung

Identivision

Identivision ICR-PH161i PIONEER Bedienungsanleitung

DIGIFUSION

DIGIFUSION FVRT150 Bedienungsanleitung