Soleus Air WM1-12E-01 Bedienungsanleitung

Models

WM1-12E-01

WM1-15E-01

WM1-18E-01

WM1-24E-01

Electronic Window Air Conditioner

Operating Instructions

V151204

12,600 BTU

15,400 BTU

18,300 BTU

24,700 BTU

Thank you for choosing a Soleus Air Air Conditioner. This owner’s manual will proide you with valu-

able information necessary for the proper care and maintenance of your new product. Please take a few

moments to thoroughly read the instructions and familiarize yourself with all the operational aspects of

your new air conditioner.

For your own records, please attach a copy of your sales receipt to this manual. Also, write the store

name/location, date purchased, and serial number below:

Store Name: ____________________________________________________

Location: ______________________________________________________

Date Purchased: _________________________________________________

Serial Number (located on back of unit): ______________________________

IMPORTANT SAFETY INSTRUCTIONS

Before installing and using your air conditioner, please read this owner’s manual carefully. Store this

manual in a safe place for future reference. Your safety and the safety of others is very important to

us. Please pay attention to all safety messages outlined in this owner’s manual.

WARNING: To reduce the risk of fire, electrical shock or injury when using your air conditioner, follow

the following basic precautions:

This is a safety alert symbol.

This symbol alerts you to potential hazards that can harm you orothers or evencause

death.

All safety messages will directly follow the safety alert symbol and/or the words

“DANGER”or “WARNING”.

Failure to immediately follow these

instructions may cause serious injury

or even death.

All Safety messages alert you of potential hazards, how to reduce the chance of injury,

and what can happen if instructions are not followed correctly.

• Plug into a grounded 3 prong outlet.

• Do not remove the ground prong.

• Do not use a plug adapter.

• Do not use an extension cord.

• Unplug the air conditioner before servicing

• Use two or more people to move and install the air

conditioner

LCDI POWER CORD AND PLUG

This air conditioner is equipped with an LCDI (Leakage Current Detection and Interruption) power cord

and plug as required by US National Electric Code 440.65. This cord consists of a length of shielded flexi-

ble cord with no termination on the load side and a LCDI attachment plug on the line side.

The LCDI power cord and plug will remove the supply source via electrical disconnect (circuit trip) if the

nominal current leakage between the cord shield and either load conductor exceeds a predetermined

value. The cord will remain de-energized until the devise has been manually reset. This is intended to re-

duce the risk of a fire in the power cord or combustible materials nearby. The cord shields are not grounded

and they must be considered a shock hazards if exposed. The cord shield must not be connected to ground

or to any exposed metal.

The test and reset buttons on the LCDI Plug are used to check if the plug is functioning properly. To test:

1. Plug power cord into wall outlet. The LED light will turn on.

2. Press TEST Button, circuit should trip, cutting power to the air conditioner. When this occurs,

3. Press RESET button to restore power to the machine. Once power is restored, the LED light

will turn on again.

If test button is pressed and unit can still be turned on, current leakage has been detected. Do not use the

air conditioner or attempt to reset the LCDI Plug. Contact Soleus Air Customer Service for troubleshooting

recommendations.

WARNING:

1. DO NOT press the TEST button while the air conditioner is operating.

2. The TEST and RESET buttons should not be used as “ON” and “OFF” switches.

3. The cord and plug are not intended to offer protection to externally connected loads or supply circuits.

4. The cord and plug are intended for indoor use only.

LED LIGHT

the LED light will turn off.

Note: Your units power cord and plug may differ from the one shown.

PARTS LIST

TOOLS NEEDED

Large Flathead Screwdriver

Tape Measurer

Adjustable Wrench or Pliers

Pencil

Level

Socket Wrenches

Phillips Head Screwdriver

Non-Hardware Part List

 Window Air Conditioner (1)

 Remote Control (1)

 AAA Batteries (2)

 Top Mounting Rail (1)

 Foam Gasket (1)

 Curtain (2)

 Window Sash Seal (1)

 Foam Seal for Bottom Rail (1)

 Owner’s Manual (1)

 Weather Insulation Board (2)

Hardware

(in plastic bag)

Qty.

Sash Lock

Screw and

Locknut

Flathead Bolt

and Locknut

Sill Angle

Bracket

Curtain Lock

Long Screws

Short Screws

WINDOW SASH SEAL

SASH LOCK AND

SHORT SCREW

TOP MOUNTING

RAIL

FOAM GASKET

SHORT SCREW

CURTAIN

CURTAIN LOCK

FOAM SEAL FOR

BOTTOM RAIL

SCREWS AND

LOCKNUTS

FLATHEAD BOLT

SILL ANGLE BRACKET

LOCKNUT

WINDOW SUPPORT

BRACKET

FRAME

ASSEMBLY

Weather Insulation Board

Remote Control

2 AAA Batteries

Owner's Manual

SPECIFICATIONS

• Noise level is measured at a distance of 3.28 ft away from the front of the unit in cooling mode.

• Power consumption is measured when the fan runs at the highest speed setting.

• These specifications are for reference only. For actual data, please refer to the rating label on the back of the unit.

Model WM1-12E-01 WM1-15E-01

Power Supply (Ph/V/Hz) 1/115/60 1/115/60

Rated Cooling Capacity (BTU/h) 12,600 15,400

Cooling Power Input (Watts) 1,000 1,230

Rated Current Cooling (Amperage) 9 12

EER 12 11.8

Noise Level dB(A) (L/H) 55/59 55/59

Airflow CFM (H/L) 600/520 700/610

Dehumidifying Capacity 52 Pints per day 74 Pints per day

Product Dimensions (W” x H” x D”) 23.625 x 17.75 x 25.375 23.625 x 17.75 x 25.375

Package Dimensions (W” x H” x D”) 26.125 x 20 x 30.5 26.125 x 20 x 30.5

Net/Gross Weight (Lbs) 106/117 110/121

Refrigerant Type R-410A R-410A

Plug Type NEMA 5-15P NEMA 5-15P

Model WM1-18E-01 WM1-24E-01

Power Supply (Ph/V/Hz) 208/230/60 208/230/60

Rated Cooling Capacity (BTU/h) 18,300 24,700

Cooling Power Input (Watts) 1,530 2,330

Rated Current Cooling (Amperage) 6.7 10.3

EER 11.8 10.3

Noise Level dB(A) (L/H) 56/61 56/61

Airflow CFM (H/L) 730/630 760/660

Dehumidifying Capacity 83 Pints per day 152 Pints per day

Product Dimensions (W” x H” x D") 26.375 x 18.625 x 26.625 26.375 x 18.625 x 26.625

Package Dimensions (W” x H” x D”) 29.5 x 20.875 X 31.125 29.5 x 20.875 X 31.125

Net/Gross Weight (Lbs) 132/154 141/163

Refrigerant Type R-410A R-410A

Plug Type NEMA 6-15P NEMA 6-20P

DISCLAIMER

ALL INFORMATION AND THE TECHNICAL SPECIFI-

CATIONS PRESENTED IN THIS USER’S MANUAL

ARE THE PRESENTATION OF THE MANUFAC-

TURER. SOLEUS HOME COMFORT HAS NOT CON-

DUCTED INDEPENDENT TEST TO THE INFORMA-

TION AND THE SPECIFICATIONS PRESENTED

HEREWITHIN.

Power supply cord with 3-prong grounding

plug and current detection device

WARNING: Avoid fire hazard or electronic shock,

DO NOT use an extension cord or an adapter plug.

DO NOT remove any prong from the power cord.

DO NOT

under any circumstances,

cut, remove, or bypass the

grounding prong!!

INSTALLATION & ASSEMBLY INSTRUCTIONS

Window Preparation

Please read all instructions prior to installing your air conditioner. Two people are recommended to install this product. If

a new electrical outlet is required, have the outlet installed by a qualified electrician before installing the unit.

Before installing the unit, check the dimensions of your window to make sure the air conditioner will fit. This unit is made

to fit inside a standard double-hung window. Make sure the window is in good shape and able to firmly hold the needed

screws. If not, make repairs prior to installing the unit.

Storm Window Requirements

A storm window frame will not allow the air conditioner to tilt properly which in turn will keep it from draining properly. To

adjust for this, attach a board or piece of wood to the sill. The board or wood piece should have a depth of at least 1 1/2”.

Make sure the board or piece of wood is approximately 1/2” higher than the storm window frame. This will allow the air

conditioner to tilt enough for proper drainage. (See FIG. 2).

Prior to Installing the Air Conditioner

1. Check for anything that could block airflow. Check the area outside of the window for things such as shrubs, trees, or

awnings. Check the inside area to make sure curtains, drapes, or blinds will not prevent proper airflow.

2. Check the available electrical outlet. The power supply must be the same as shown on the unit serial nameplate

(located on the left side of the unit, near the front faceplate). Be sure the outlet is close enough for the power cord to

reach.

3. Carefully unpack the air conditioner. Remove all packing material and make sure the floor is protected when remov-

ing. Due to the large size of this air conditioner, two people should move the unit together.

When handling the unit, be careful to avoid cuts from

the sharp metal edges and aluminum fins on the front

and rear coils.

Model WM1-12E-01 / WM1-15E-01 WM1-18E-01 / WM1-24E-01

Unit Height 17 3/4" 18 5/8"

Unit Width 23 5/8" 26 3/8"

Min.Window Opening(See FIG 1) 1ϴϰϯ" 19 7/8"

Min. Window Width 28 1/8" 30"

Max Window Width 41 3/4" 50 "

FIG. 1

18 3/4", / 19 7/8"MIN

FIG. 2

18 3/4", / 19 7/8"MIN

INSTALLATION & ASSEMBLY INSTRUCTIONS - WINDOW MOUNTING

REMOVE CHASSIS

1. Pull down the front panel and remove the filter.(See Fig. 3)

2. Lift the front panel upwards to remove and place to the side.

3. Locate the four faceplate screws and remove. These screws will need to be re-installed prior to mounting the air con-

ditioner.(See Fig. 4)

4. After removing the screws, gently pull away the faceplate from the air conditioner cabinet. Remove the ground screw

and save for reinstallation later.(See Fig. 5& 6)

5. Remove the two screws from top of the unit. (See Fig. 7) Hold the cabinet while pulling on the base handle, and care-

Fig. 3 Fig. 4

Fig. 5 Fig. 6

fully remove the unit.

Fig. 7

ASSEMBLY & INSTALLATION (CONT.)

Weather Insulation Board Installation

NOTE: The Weather Installation Board adds an extra layer of

insulation to keep air from passing through the sides of the win-

dow air conditioner.

1. Using a sharp blade or scissors, slowly cut the

Weather Insulation Board to a size that will fit inside of

the side curtain rails and completely cover the curtain.

2. Once properly sized, remove the backing to expose

the adhesive tape.

3. Place the Weather Insulation Board over the left curtain

and firmly press and hold for 5 seconds.

4. Place the Weather Insulation Board over the right cur-

tain and firmly press and hold for 5 seconds (FIG. 7.1).

Fig. 7.1

Placing the Cabinet Inside the Window

1. Attach the top mounting rail to the unit with short

screws (See Fig.8).

1. Open the window and place the cabinet in the middle

of the window sill.

2. Make sure the bottom rail is seated over the window-

sill as shown below. Bring the window down tempo-

rarily behind the top mounting rail to hold the cabinet

in place.

2. Slide the free end of the curtain into the side panel of

the air conditioner. Do this for each side. The flange

for securing the curtain into the window sill will be fac-

ing the room side when installed (See Fig.9).

3. Fasten the curtains to the unit with short screws (See

Fig.10)

3. Fasten cabinet to window sill using three long screws.

Pre-drill holes if needed. Add the bottom rail seal over

the screws (See Fig.11).

Curtain Installation

Weather Insulation

Board

Curtain

Fig. 8

Fig. 9

Fig. 10

Fig. 11

Top Mounting Rail

Long Screw

Bottom Rail Seal

Install Support Brackets

1. Hold each support bracket flush against the outside of

the window sill. Tighten each bracket to the bottom of

the cabinet as shown below. Mark the brackets at top

lever of the window sill and then remove.

2. Assemble the sill angle brackets to the support brack-

ets at the marked position as shown above. Hand

tighten, but not all the way for any changes that may

need to be made later during installation.

3. Install the support brackets (with sill angle brackets

attached) to the bottom of the cabinet as shown below.

4. Tighten all 6 bolts securely.

Install the Window Lock and Sash Seal

1. Trim the sash seal to fit the width of the window. Insert

the sash seal into space between the upper and lower

sashes.

2. Attach the right angle safety lock as shown below.

MARK

SCREW &

LOCKNUTS

SAFETY LOCK

LONG SCREW

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Soleus Air Klimaanlage Handbücher

Soleus Air

Soleus Air TTWM1-10-01 Bedienungsanleitung

Soleus Air

Soleus Air WM1-12E2-01 Bedienungsanleitung

Soleus Air

Soleus Air SG-PAC-12E1 Bedienungsanleitung

Soleus Air

Soleus Air PH5 Series Bedienungsanleitung

Soleus Air

Soleus Air SG-WAC-06ESE-C Bedienungsanleitung

Soleus Air

Soleus Air WS1-05M2-02 Bedienungsanleitung

Soleus Air

Soleus Air KFCHP5-09-ID Bedienungsanleitung

Soleus Air

Soleus Air SG-PAC-10E5 Bedienungsanleitung

Soleus Air

Soleus Air WS1-06E-02 Bedienungsanleitung

Soleus Air

Soleus Air HCC-W08ES-A1 Bedienungsanleitung

Soleus Air

Soleus Air SG-PAC-08E3 Bedienungsanleitung

Soleus Air

Soleus Air SG-WAC-25HCE Bedienungsanleitung

Soleus Air

Soleus Air PH3-09R Bedienungsanleitung

Soleus Air

Soleus Air GM-CAC-08ESE Bedienungsanleitung

Soleus Air

Soleus Air HCC-C09HP-A Bedienungsanleitung

Soleus Air

Soleus Air PH5-13R-32D Bedienungsanleitung

Soleus Air

Soleus Air MAC-8000 Bedienungsanleitung

Soleus Air

Soleus Air KFHHP-22 Betriebsanleitung

Soleus Air

Soleus Air WM1-05M2-01 Bedienungsanleitung

Soleus Air

Soleus Air KFIHP-09-ID Bedienungsanleitung

Soleus Air

Soleus Air KC-15U Bedienungsanleitung

Soleus Air

Soleus Air KY4-100 Bedienungsanleitung

Soleus Air

Soleus Air WM1-06E-01 Bedienungsanleitung

Soleus Air

Soleus Air KY2-34 Bedienungsanleitung

Beliebte Klimaanlage Handbücher anderer Marken

Panasonic

Panasonic CS-E12HKEW Bedienungsanleitung

nedis

nedis ACMB1WT7 Bedienungsanleitung

Daikin

Daikin FCFV50A Bedienungsanleitung

Fujitsu

Fujitsu Inverter ASBA30JFC Bedienungsanleitung

Toshiba

Toshiba RAS-M10SMUV-E Bedienungsanleitung

Daikin

Daikin FXLQ20MAVE Bedienungsanleitung

CIAT

CIAT Magister 2 Series Leitfaden

Bestron

Bestron AAC6000 Bedienungsanleitung

Frigidaire

Frigidaire FFRE0533S1E0 Bedienungsanleitung

Samsung

Samsung AS09HM3N Bedienungsanleitung

Frigidaire

Frigidaire CRA073PU11 Betriebsanleitung

McQuay

McQuay MCK020A Bedienungsanleitung

Webasto

Webasto Frigo Top 25 DS Bedienungsanleitung

Frigidaire

Frigidaire FAZ12ES2A Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MSC-GE20VB Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PLA-M100EA Bedienungsanleitung

Daikin

Daikin Split Sensira R32 Bedienungsanleitung

Carrier

Carrier 42HVM109303 Bedienungsanleitung