Soleus Air WM1-15E-01 Bedienungsanleitung

Electronic Window Air Conditioner

Operating Instructions

V170124

Models

WM1-15E-01

15,400 BTU

WM1-18E-01

18,300 BTU

WM1-24E-01

24,700 BTU

Thank you for choosing a Soleus Air Air Conditioner. This owner’s manual will provide you with

valuable information necessary for the proper care and maintenance of your new product. Please take

a few moments to thoroughly read the instructions and familiarize yourself with all the operational

aspects of your new air conditioner.

For your own records, please attach a copy of your sales receipt to this manual. Also, write the store

name/location, date purchased, and serial number below:

Store Name:

Location:

Date Purchased:

Serial Number (located on back of unit):

Before installing and using your air conditioner, please read this owner’s manual carefully. Store this manual in a

safe place for future reference. Your safety and the safety of others is very important to us. Please pay attention to

all safety messages outlined in this owner’s manual.

WARNING: To reduce the risk of fire, electrical shock or injury when using your air conditioner, follow

the following basic precautions:

Plug into a grounded 3 prongoutlet.

Do not remove the ground prong.

Do not use a plug adapter.

Do not use an extensioncord.

Unplug the air conditioner before servicing

Use two or more people to move and install theair

conditioner

This is a safety alert symbol.

This symbol alerts you to potential hazards that can harm you or others or even cause

death.

All safety messages will directly follow the safety alert symbol and/or the words

“DANGER” or “WARNING”.

All Safety messages alert you of potential hazards, how to reduce the chance of injury,

and what can happen if instructions are not followed correctly.

Failure to immediately follow these

instructions may cause serious injury

or even death.

PURCHASE INFORMATION

SAFETY INSTRUCTIONS

This air conditioner is equipped with an LCDI (Leakage Current Detection and Interruption) power cord and

plug as required by US National Electric Code 440.65. This cord consists of a length of shielded flexible cord

with no termination on the load side and a LCDI attachment plug on the line side.

The LCDI power cord and plug will remove the supply source via electrical disconnect (circuit trip) if the

nominal current leakage between the cord shield and either load conductor exceeds a predetermined value.

The cord will remain de-energized until the devise has been manually reset. This is intended to reduce the risk

of a fire in the power cord or combustible materials nearby. The cord shields are not grounded and they must

be considered a shock hazards if exposed. The cord shield must not be connected to ground or to any exposed

metal.

The test and reset buttons on the LCDI Plug are used to check if the plug is functioning properly. To test:

1. Plug power cord into wall outlet. The LED light will turn on.

2. Press TEST Button, circuit should trip, cutting power to the air conditioner. When this occurs,

the LED light will turn off.

3. Press RESET button to restore power to the machine. Once power is restored, the LED light

will turn on again.

If test button is pressed and unit can still be turned on, current leakage has been detected. Do not use the air

conditioner or attempt to reset the LCDI Plug. Contact Soleus Air Customer Service for troubleshooting

recommendations.

LED LIGHT

Note: Your units power cord and plug may differ from the one shown.

WARNING:

1. DO NOT press the TEST button while the air conditioner is operating.

2. The TEST and RESET buttons should not be used as “ON” and “OFF”switches.

3. The cord and plug are not intended to offer protection to externally connected loads or supply circuits.

4. The cord and plug are intended for indoor use only.

POWER CORD AND PLUG

Hardware

(in plastic bag) Qty.

Sash Lock 1

Screw and 4

Locknut

Flathead Bolt 2

and Locknut

Sill Angle 2

Bracket

Curtain Lock 2

Non-Hardware Part List

Long Screws 13

Short Screws 10

Window Air Conditioner (1)

Remote Control (1)

AAA Batteries (2)

Top Mounting Rail (1)

Foam Gasket (1)

Curtain (2)

Window Sash Seal (1)

Foam Seal for Bottom Rail (1)

Owner’s Manual (1)

Weather Insulation Board (2)

CURTAIN

CURTAIN LOCK

FOAM SEAL FOR

BOTTOM RAIL

SCREWS AND

LOCKNUTS

FRAME

ASSEMBLY

WINDOW SUPPORT

BRACKET

Weather Insulation Board

SILL ANGLE BRACKET

FLATHEAD BOLT LOCKNUT

Remote Control 2 AAA Batteries Owner's Manual

WINDOW SASH SEAL

SASH LOCK AND

SHORT SCREW

FOAM GASKET TOP MOUNTING

RAIL

SHORT SCREW

TOOLS NEEDED

Large Flathead Screwdriver

Tape Measurer

Adjustable Wrench or Pliers

Pencil

Level

Socket Wrenches

Phillips Head Screwdriver

PACKAGE CONTENTS

Noise level is measured at a distance of 3.28 ft away from the front of the unit in cooling mode.

Power consumption is measured when the fan runs at the highest speed setting.

These specifications are for reference only. For actual data, please refer to the rating label on the back of the unit.

Model

WM1-15E-01

Power Supply (Ph/V/Hz)

1/115/60

Rated Cooling Capacity (BTU/h)

15,400

Cooling Power Input (Watts)

1,230

Rated Current Cooling (Amperage)

EER

11.8

Noise Level dB(A) (L/H)

55/59

Airflow CFM (H/L)

700/610

Dehumidifying Capacity

74 Pints per day

Product Dimensions (W” x H” x D”)

23.625 x 17.75 x 25.375

Package Dimensions (W” x H” x D”)

26.125 x 20 x 30.5

Net/Gross Weight (Lbs)

110/121

Refrigerant Type

R-410A

Plug Type

NEMA 5-15P

Model

WM1-18E-01

WM1-24E-01

Power Supply (Ph/V/Hz)

208/230/60

Rated Cooling Capacity (BTU/h)

18,300

24,700

Cooling Power Input (Watts)

1,530

2,330

Rated Current Cooling (Amperage)

6.7

10.3

EER

11.8

10.3

Noise Level dB(A) (L/H)

56/61

Airflow CFM (H/L)

730/630

760/660

Dehumidifying Capacity

83 Pints per day

152 Pints per day

Product Dimensions (W” x H” x D")

26.375 x 18.625 x 26.625

Package Dimensions (W” x H” x D”)

29.5 x 20.875 X 31.125

Net/Gross Weight (Lbs)

132/154

141/163

Refrigerant Type

R-410A

Plug Type

NEMA 6-15P

NEMA 6-20P

SPECIFICATIONS

DISCLAIMER

ALL INFORMATION AND THE TECHNICAL SPECIFI-

CATIONS PRESENTED IN THIS USER’S MANUAL

ARE THE PRESENTATION OF THE MANUFAC-

TURER. SOLEUS N.A HAS NOT CON-DUCTED

INDEPENDENT TEST TO THE INFORMA- TION AND

THE SPECIFICATIONS PRESENTED HEREWITHIN.

WARNING:

Avoid fire hazard or electronic shock,

DONOT use an extension cord or an adapter plug.

DONOT remove any prong from the power cord.

DO NOT

under any circumstances,

cut, remove, or bypass the

grounding prong!!

Power supply cord with 3-prong grounding

plug and current detection device

ELECTRICAL SAFETY

Window Preparation

Please read all instructions prior to installing your air conditioner. Two people are recommended to install this product. If

a new electrical outlet is required, have the outlet installed by a qualified electrician before installing the unit.

Before installing the unit, check the dimensions of your window to make sure the air conditioner will fit. This unit is made

to fit inside a standard double-hung window. Make sure the window is in good shape and able to firmly hold the needed

screws. If not, make repairs prior to installing the unit.

Model

WM1-15E-01

WM1-18E-01 / WM1-24E-01

Unit Height

17 33/4"

18 5/8"

Unit Width

23 5/8"

26 3/8"

Min.Window Opening(See FIG

18 4/3"

19 7/8"

Min. Window Width

28 1/8"

30"

Max Window Width

41 3/4"

50 "

Storm Window Requirements

A storm window frame will not allow the air conditioner to tilt properly which in turn will keep it from draining properly. To

adjust for this, attach a board or piece of wood to the sill. The board or wood piece should have a depth of at least 1 1/2”.

Make sure the board or piece of wood is approximately 1/2” higher than the storm window frame. This will allow the air

conditioner to tilt enough for proper drainage. (See FIG. 2).

FIG. 1 FIG. 2

19 7/8"MIN

Prior to Installing the Air Conditioner

1. Check for anything that could block airflow. Check the area outside of the window for things such as shrubs, trees,or

awnings. Check the inside area to make sure curtains, drapes, or blinds will not prevent proper airflow.

2. Check the available electrical outlet. The power supply must be the same as shown on the unit serial nameplate

(located on the left side of the unit, near the front faceplate). Be sure the outlet is close enough for the power cord to

reach.

3. Carefully unpack the air conditioner. Remove all packing material and make sure the floor is protected when remov-

ing. Due to the large size of this air conditioner, two people should move the unit together.

When handling the unit, be careful to avoid cuts from

the sharp metal edges and aluminum fins on the front

and rear coils.

18 3/4", /

18 3/4", / 19 7/8"MIN

INSTALLATION

ION

INSTALLATION & ASSEMBLY INSTRUCTIONS - WINDOW MOUNTING

REMOVE CHASSIS

1. Pull down the front panel and remove the filter. (See Fig.3)

2. Lift the front panel upwards to remove and place to theside.

3. Locate the four faceplate screws and remove. These screws will need to be re-installed prior to mounting the air con-

ditioner. (See Fig. 4)

4. After removing the screws, gently pull away the faceplate from the air conditioner cabinet. Remove the ground screw

and save for reinstallation later. (See Fig. 5 & 6)

5. Remove the two screws from top of the unit. (See Fig. 7) Hold the cabinet while pulling on the base handle, and care-

fully remove the unit.

Fig. 3

Fig. 4

Fig. 5

Fig. 6

Fig. 7

INSTALLATION

ION

Curtain Installation

Top Mounting Rail

1. Attach the top mounting

rail to the unit with short

screws (Fig.8)

Fig. 8

2. Slide the free end of the curtain into the side panel of theair

conditioner. Do this for each side. The flange for securing

the curtain into the window sill will be facing the room side

when installed ( Fig.9).

Weather Insulation Board Fig.11

Curtain

Fig. 9

Placing the Cabinet Inside the Window

Set the cabinet in the window so that is centered.

Place the unit so that front edge of the bottom railis

against the back edge of thesill.

Bring the window down so that the front edge ofthe

top rail is in front of the window. Be sure the unit is

tilting slightly to the outside.

Fasten the curtains to the unit with short screws(Fig.10). Window

Frame

1/4”

Top Rail

Bottom Rail

Fig. 10

Weather Insulation Board Installation

NOTE: The Weather Insulation Board adds an extra layer of insulation

to keep air from passing through the sides of the window air conditioner.

1. Using a sharp blade or scissors, slowly cut the Weather

Insulation Board to a size that will fit inside of the sidecur-

tain rails and completely cover thecurtain.

2. Once properly sized, remove the backing to expose thead-

hesive tape.

3. Place the Weather Insulation Board over the left curtainand

firmly press and hold for 5seconds.

3. Fasten cabinet to window sill using three long screws. Pre-

drill holes if needed. Add the bottom rail seal overthe

screws (Fig.12).

Bottom Rail Seal

4. Repeat above steps to install the Weather InsulationBoard

on right curtain (Fig.11). Fig. 12 Long Screw

INSTALLATION

ION

Install Support Brackets

1. Hold each support bracket flush against the outside of

the window sill. Tighten each bracket to the bottom of

the cabinet as shown below. Mark the brackets at top

lever of the window sill and then remove.

Install the Window Lock and Sash Seal

1. Trim the sash seal to fit the width of the window.Insert

the sash seal into space between the upper and lower

sashes.

MARK

2. Attach the right angle safety lock as shownbelow.

2. Assemble the sill angle brackets to the support brack-

ets at the marked position as shown above. Hand

tighten, but not all the way for any changes that may

need to be made later duringinstallation.

3. Install the support brackets (with sill angle brackets

attached) to the bottom of the cabinet as shownbelow.

4. Tighten all 6 boltssecurely.

SCREW &

LOCKNUTS

SAFETY LOCK

LONG SCREW

INSTALLATION

ION

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Soleus Air Klimaanlage Handbücher

Soleus Air

Soleus Air SG-WAC-05SM Bedienungsanleitung

Soleus Air

Soleus Air GL-PAC-08E4 Bedienungsanleitung

Soleus Air

Soleus Air MA-9000AH Bedienungsanleitung

Soleus Air

Soleus Air SG-WAC-15ESE Bedienungsanleitung

Soleus Air

Soleus Air 000 BTU Evaporative Portable Air Conditioner and... Bedienungsanleitung

Soleus Air

Soleus Air KY-32E Bedienungsanleitung

Soleus Air

Soleus Air GM-CAC-08ESE Bedienungsanleitung

Soleus Air

Soleus Air GM-WAC-25ESE-C Bedienungsanleitung

Soleus Air

Soleus Air SG-WAC-10ESE-F Bedienungsanleitung

Soleus Air

Soleus Air GM-WAC-15ESE-C Bedienungsanleitung

Soleus Air

Soleus Air GH-PAC-12E1 Bedienungsanleitung

Soleus Air

Soleus Air WS2-06E-201 Bedienungsanleitung

Soleus Air

Soleus Air HCB-P13HP-D Bedienungsanleitung

Soleus Air

Soleus Air KFHHP-22 Betriebsanleitung

Soleus Air

Soleus Air SG-TTW-10ESE Bedienungsanleitung

Soleus Air

Soleus Air air-condition Bedienungsanleitung

Soleus Air

Soleus Air KFCHP5-09-ID Bedienungsanleitung

Soleus Air

Soleus Air KFHHP-22 Technisches Datenblatt

Soleus Air

Soleus Air PE6-10R-03 Bedienungsanleitung

Soleus Air

Soleus Air PH1-12R-03 Bedienungsanleitung

Soleus Air

Soleus Air Soleus LX-100 LX-100 Bedienungsanleitung

Soleus Air

Soleus Air MAC-8000 Bedienungsanleitung

Soleus Air

Soleus Air SA-50 Bedienungsanleitung

Soleus Air

Soleus Air GM-PAC-08E3 Bedienungsanleitung

Beliebte Klimaanlage Handbücher anderer Marken

Panasonic

Panasonic CS-E12HKEW Bedienungsanleitung

nedis

nedis ACMB1WT7 Bedienungsanleitung

Daikin

Daikin FCFV50A Bedienungsanleitung

Fujitsu

Fujitsu Inverter ASBA30JFC Bedienungsanleitung

Toshiba

Toshiba RAS-M10SMUV-E Bedienungsanleitung

Daikin

Daikin FXLQ20MAVE Bedienungsanleitung

CIAT

CIAT Magister 2 Series Leitfaden

Bestron

Bestron AAC6000 Bedienungsanleitung

Frigidaire

Frigidaire FFRE0533S1E0 Bedienungsanleitung

Samsung

Samsung AS09HM3N Bedienungsanleitung

Frigidaire

Frigidaire CRA073PU11 Betriebsanleitung

McQuay

McQuay MCK020A Bedienungsanleitung

Webasto

Webasto Frigo Top 25 DS Bedienungsanleitung

Frigidaire

Frigidaire FAZ12ES2A Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MSC-GE20VB Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PLA-M100EA Bedienungsanleitung

Daikin

Daikin Split Sensira R32 Bedienungsanleitung

Carrier

Carrier 42HVM109303 Bedienungsanleitung