Sonnet TEMPO Trio Bedienungsanleitung

Remember to register your product online at http://registration.sonnettech.com to be informed of future upgrades and product releases.

Software updates and links are available from the Sonnet web site at www.sonnettech.com.

•

Online support form available at http://supportform.sonnettech.com.

Sonnet Technologies Customer Service hours are Mon.-Fri., 7 a.m.–5 p.m. Pacific Time

•

Customer Service Phone: 1-949-472-2772 • E-mail: support@sonnettech.com

Sonnet Technologies, Inc., 15 Whatney, Irvine, California 92618-2808 USA • Tel:

949-587-3500 Fax:

949-457-6350

©2002 Sonnet Technologies, Inc. All rights reserved. Sonnet, the Sonnet logotype, Simply Fast, the Simply Fast logotype, and Tempo are trademarks of Sonnet Technologies, Inc.Tempo Trio includes technology by FirmTek, LLC.

Other product names are trademarks of their respective owners.All specifications subject to change without notice. Printed in the USA. QS-FWU2-W-E-112102

Quick Start Guide for Tempo Trio

You Should Have

The following items should be included in your product package:

• One Tempo Trio PCI Combo Card for Windows PCs

• One Ultra ATA Cable (supporting two internal hard drives)

• Eight screws (for mounting hard drives)

• One Tempo Trio Windows Drivers diskette

The following items may be required for installation:

• Medium Phillips screwdriver

• Small flat blade screwdriver

• Needle nose pliers

• Drive mounting brackets/carriers or drive mounting sleds

(sold separately)

• One additional Ultra ATA Cable (sold separately)

• One or more power cable Y-adapters (sold separately)

You may need the following items to connect peripherals to the Tempo Trio:

• One or more FireWire (IEEE 1394) cables (sold separately)

• One or more USB cables (sold separately)

• One or more USB hubs (sold separately)

Hardware and Operating System Requirements

The Tempo Trio requires the following in order to operate in your system:

• One available PCI 2.1 slot

• Pentium II (or equivalent) or higher

• Windows 98SE, Windows Me, Windows 2000, or Windows XP

• One or more available drive bays (depending on configuration)

PCI Adapter Combo Card with ATA/133, FireWire®, and USB 2.0

For Windows®PCs

.Support Note: We recommend that you make a backup of important

information on your system’s current hard drive(s) prior to installing new

hardware or software.

When handling computer products, you must take care to prevent components

from being damaged by static electricity. Before opening your computer or

removing parts from their packages, always ground yourself first by touching an

unpainted metal part of the computer, such as a port access cover, and work in

an area free of static electricity; avoid carpeted areas. Handle all electrical com-

ponents only by their edges, and avoid touching connector traces and compo-

nent pins.

Quick Start Guide for Tempo Trio (Windows Version)

Installation Preparation

Prior to installing the Tempo Trio into your system, you should read the section

in your computer’s user manual that addresses PCI card installation.

START HERE! USB 2.0 Driver Installation—All Windows Versions

This section describes the installation of USB 2.0 drivers to enable USB 2.0 device

support through the Tempo Trio; you must install these drivers prior to installing

the Tempo Trio card.

1. Turn on your computer, and wait for Windows startup to finish.

2. Insert the Tempo Trio Windows Drivers diskette into your floppy drive.

3. From the taskbar, click on Start > Run…

4. When the Run window appears, type A:\U2V2_08, and then click OK; the

USB 2.0 drivers will be installed into your system.

5. When the Finished window appears, eject the diskette from your computer’s

floppy drive, and then click Close to restart your system and complete the

installation. You may now install the Tempo Trio card and the additional

driver software included with this product.

Tempo Trio Card Installation Steps

This section covers the installation of the Tempo Trio PCI combo card into your

computer. For information on attaching hard drives, see page 8.

1. Shut down your computer.

2. Open your computer to access its expansion card area (PCI slots); refer to

your computer’s user manual for specific information.

3. Remove the Tempo Trio card from its anti-static packaging.

4. Locate an available PCI slot inside your computer and, if present, remove its

port access cover from the rear of the computer.

5. Install the Tempo card into the PCI slot; make sure the card is firmly seated

and secured (Figure 1).

6. If you are installing hard drives at this time, refer to “Hard Drive Installation

Preparation” and “Hard Drive Installation Steps” on page 8.

7. Close your computer (after installing any drives).

Tempo Trio

PCI slots

The location of your

computer’s PCI slots may

vary from this illustration.

Figure 1

Quick Start Guide for Tempo Trio (Windows Version)

Windows 98SE Driver Installation

This section describes the installation of drivers to support the Tempo Trio in

systems running Windows 98SE. If your system is running Windows Me, skip to

page 5. If your system is running Windows 2000, skip to page 6. If your system is

running Windows XP, skip to page 7.

1. Turn on your computer; during Windows startup, New Hardware Found win-

dows will briefly appear.

2. When the Add New Hardware Wizard (PCI Standard PCI-to-PCI Bridge) win-

dow appears, click Next.

3. When the next window appears, insert the Windows 98SE CD into your

computer’s CD-ROM drive, select “Search for best driver for your device

(Recommended),” and then click Next.

4. When the next window appears, click Next.

5. When the message stating “Windows is now ready to install the best

driver…” appears, click Next.

6. When the message stating “Windows has finished installing the software

that your new device requires,” appears, click Finish; the window will close,

and then several New Hardware Found windows will briefly appear.

7. When the next Add New Hardware Wizard (NEC USB Open Host Controller)

window appears, click Next.

8. When the next window appears, select “Search for best driver for your device

(Recommended),” and then click Next.

9. When the next window appears, click Next.

10. When the message stating “Windows has found an updated driver for this

device…,” click Next.

11. When the message stating “Windows is now ready to install the best

driver…” appears, click Next.

12. When the message stating “Windows has finished installing the software

that your new device requires,” appears, click Finish; the window will close.

13. When the next Add New Hardware Wizard (NEC USB Open Host Controller)

window appears, click Next. Note: This is correct; this driver is installed two

times (once for each USB port).

14. When the next window appears, select “Search for best driver for your device

(Recommended),” and then click Next.

Support Note: You must use the Windows 98SE CD-ROM to install

some of the drivers necessary to support the Tempo Trio in your system.

Depending on your system’s configuration before you install the Tempo Trio (for

example, you’ve previously installed a USB card), some of the drivers required to

support the Tempo Trio card may have already been installed. If this is the case,

you may not need to perform some of the steps listed.

Quick Start Guide for Tempo Trio (Windows Version)

Windows 98SE Driver Installation (continued)

15. When the next window appears, click Next.

16. When the message stating “Windows has found an updated driver for this

device…,” click Next.

17. When the message stating “Windows is now ready to install the best

driver…” appears, click Next.

18. When the message stating “Windows has finished installing the software

that your new device requires,” appears, click Finish; the window will close,

and then New Hardware Found windows will appear.

19. When the Add New Hardware Wizard (PCI OHCI Compliant IEEE 1394 Host

Controller) window appears, click Next.

20. When the next window appears, select “Search for best driver for your device

(Recommended),” and then click Next.

21. When the next window appears, click Next.

22. When the message stating “Windows is now ready to install the best

driver…” appears, click Next.

23. When the message stating “Windows has finished installing the software

that your new device requires,” appears, click Finish; the window will close.

24. When the next Add New Hardware Wizard (PCI Mass Storage Controller) win-

dow appears, click Next.

25. When the next window appears, select “Search for best driver for your device

(Recommended),” and then click Next.

26. Insert the Tempo Trio Windows Drivers diskette into your floppy drive, select

“Specify a location,” then type A:\WIN9X-ME, and then click Next.

27. When the message stating “Windows is now ready to install the best

driver…” appears, click Next.

28. When the message stating “Windows has finished installing the software

that your new device requires,” appears, click Finish; the window will close.

29. When the System Settings Change window appears, eject the Tempo Trio

Windows Drivers diskette from your floppy drive, and then click Yes to

restart your system and complete the driver installation.

30. Upon restarting your system, several New Hardware Found windows will

briefly appear, and additional drivers will be installed; you must now format

any attached hard drives. Skip to “Drive Formatting—Windows 98SE and

Windows Me” on page 10.

Quick Start Guide for Tempo Trio (Windows Version)

Windows Me Driver Installation

This section describes the installation of drivers to support the Tempo Trio in

systems running Windows Me. If your system is running Windows 98SE, go back

to page 3. If your system is running Windows 2000, skip to page 6. If your system

is running Windows XP, skip to page 7.

1. Turn on your computer; during Windows startup, an Updating Hardware Info

window will appear.

2. When the Add New Hardware Wizard (PCI Standard PCI-to-PCI Bridge) win-

dow appears, click Next.

3. When the next window appears, select “Automatic Search for a better driver

(Recommended),” and then click Next.

4. When the next window appears, click Finish; the window will close, and

then another New Hardware Found window will briefly appear.

5. When the next Add New Hardware Wizard (PCI OHCI Compliant IEEE 1394

Host Controller, or PCI Mass Storage Controller) window appears, click Next.

6. When the next window appears, select “Automatic Search for a better driver

(Recommended),” and then click Next.

7. When the next window appears, click Finish; the window will close, and

then New Hardware Found windows will appear.

8. When the Add New Hardware Wizard (Win9x-Me Promise Ultra133 (tm) IDE

Controller) window appears, click Next.

9. When the next window appears, select “Specify the location of the driver

(Advanced),” and then click Next.

10. Insert the Tempo Trio Windows Drivers diskette into your floppy drive, and

then click Next.

11. When the message stating “Windows has found multiple software pack-

ages…” appears, click Next.

12. When the message stating “Windows is now ready to install the best

driver…” appears, click Next.

13. When the message stating “Windows has finished installing the software

that your new device requires,” appears, click Finish; the window will close.

14. At the next prompt, eject the Tempo Trio Windows Drivers diskette from

your floppy drive, and then click Yes to restart your system; you must now

format any attached hard drives. Skip to “Drive Formatting—Windows 98SE

and Windows Me” on page 10.

Support Note: Depending on your system’s configuration before you

install the Tempo Trio (for example, you’ve previously installed a USB

card), some of the drivers required to support the Tempo Trio card may have

already been installed. If this is the case, you may not need to perform some of

the steps listed.

Quick Start Guide for Tempo Trio (Windows Version)

Windows 2000 Driver Installation

This section describes the installation of drivers to support the Tempo Trio in

systems running Windows 2000. If your system is running Windows 98SE, go

back to page 3. If your system is running Windows Me, go back to page 5. If your

system is running Windows XP, skip to page 7.

1. Turn on your computer; during Windows startup, several New Hardware

Found windows will appear.

2. When the Found New Hardware Wizard window appears, click Next.

3. When the Install Hardware Device Drivers window appears, select “Search for a

suitable driver for my device (recommended),” and then click Next.

4. When the Locate Driver Files window appears, insert the Tempo Trio

Windows Drivers diskette into your floppy drive, and then click Next.

5. When the Driver Files Search Results window appears, select “Install on of the

other drivers,” and then click Next.

6. From the list that appears, select “Win2000 Promise Ultra133...,” and then

click Next.

7. When the Digital Signature Not Found window appears, click Yes; the Mass

Storage Controller driver will be installed.

8. When the Completing the Found New Hardware Wizard window appears,

click Finish; the window will close, several New Hardware Found windows will

appear, and additional drivers will be installed.

9. Eject the Tempo Trio Windows Drivers diskette from your floppy drive, and

then restart your computer to complete the installation. You must now for-

mat any attached hard drives. Skip to “Drive Formatting—Windows 2000”

on page 12.

Support Note: Depending on your system’s configuration before you

install the Tempo Trio (for example, you’ve previously installed a USB

card), some of the drivers required to support the Tempo Trio card may have

already been installed. If this is the case, you may not need to perform some of

the steps listed.

Quick Start Guide for Tempo Trio (Windows Version)

Windows XP Driver Installation

This section describes the installation of drivers to support the Tempo Trio in

systems running Windows XP. If your system is running Windows 98SE, go back

to page 3. If your system is running Windows Me, go back to page 5. If your sys-

tem is running Windows 2000, go back to page 6.

1. Turn on your computer; during Windows startup, several New Hardware

Found pop-ups will appear.

2. When the Found New Hardware Wizard (NEC PCI to USB Enhanced Host

Controller B1) window appears, click Next; the appropriate driver will be

installed.

3. When the Completing the Found New Hardware Wizard window appears,

click Finish.

4. When the next Found New Hardware Wizard (Mass Storage Controller) win-

dow appears, select “Install from a list or specific location (Advanced),” and

then click Next.

5. When the next window appears asking you to choose your search and instal-

lation options, insert the Tempo Trio Driver diskette into your floppy drive,

and then select “Search for the best drivers in these locations,” and “Search

removable media (floppy, CD-ROM…,” and then click Next.

6. When the next window appears, select “WinXP Promise…,” and then click

Next.

7. When the Hardware Installation window appears, click Continue Anyway; the

appropriate driver will be installed.

8. When the Completing the Found New Hardware Wizard window appears, eject

the Tempo Trio Driver diskette from your floppy drive, and then click Finish.

9. When the next window appears, click Yes to restart your system and com-

plete the driver installation. You must now format any attached hard drives.

Skip to “Drive Formatting—Windows XP” on page 14.

Support Note: Depending on your system’s configuration before you

install the Tempo Trio (for example, you’ve previously installed a USB

card), some of the drivers required to support the Tempo Trio card may have

already been installed. If this is the case, you may not need to perform some of

the steps listed.

Hard Drive Installation Preparation:

Prior to installing the Tempo Trio and hard drives into your system, you should

familiarize yourself with the parts to be installed. We also strongly recommend

that you read the sections in your computer’s user manual that address hard drive

and PCI card installation.

1. Identify the connectors on the included Ultra ATA cable as shown in

Figure 2; the host connector plugs into the Tempo Trio card, while the mas-

ter and slave connectors plug into the hard drives.

2. Remove the hard drive from its packaging.

3. Locate the jumper block on your hard drive. Figure 3 shows the two most

common jumper block locations.

Hard Drive Installation Steps

This section covers the configuration and installation of one or more hard drives

into your system.

1. Shut down your computer.

2. Open your computer to access the expansion card area (PCI slots) and drive

bay(s); refer to your computer’s user manual for specific information.

3. Configure the hard drives’ jumpers as follows:

• When installing one drive, you must set its jumpers to the single setting

when available, or the master setting when not (Figure 4). When connect-

ing two drives to the supplied Ultra ATA cable, you must set the jumpers

on one drive to the master setting, and to the slave setting on the other

(Figure 4).

• When installing two drives connected to two Ultra ATA cables, you must

set the jumpers on each drive to the single setting when available, or the

master setting when not (Figure 4). When connecting three or four drives

to two Ultra ATA cables, you must set the jumpers on two drives to the

master setting, and to the slave setting on the other drive(s) (Figure 4).

Quick Start Guide for Tempo Trio (Windows Version)

Support Note: Technical knowledge may be required to gain access to

the drive expansion bays in certain computer models. We recommend

you first consult your computer’s user manual. If you feel you are unable to

install the computer hardware, contact a qualified technician.

Support Note: Most hard drives are factory preset for use as a single or

master drive. To change the setting, you will need to reconfigure the hard

drives’ jumpers. Be sure the jumpers are configured properly, otherwise, your

computer may not boot, or your new drives may not be recognized.

er block

jumper block

Figure 3

host

connector

(blue)

connects to

Tempo Trio

slave

connector

(gray)

master

connector

(black)

40-pin/80-wire Ultra ATA cable

Figure 2

.Support Note: Refer to the hard drive user’s manual for jumper

setting information specific to your drives. Alternately, you may find

jumper setting information printed on your hard drives’ labels. Make sure the

drives are oriented the same way as the illustration before moving jumpers.

One Cable Two Cables

Three

Drives

Four

Drives

Two

Drives

One

Drive

—

master, slave

single

(or master)

master, master,

slave

master, master,

slave, slave

master (or single),

master (or single)

—

Drive Jumper Settings

Figure 4

Quick Start Guide for Tempo Trio (Windows Version)

4. Install the hard drives into the drive expansion bays. (Depending on your

computer model, mounting brackets/carriers or mounting sleds may be

required to install your hard drives. Refer to your computer’s user manual.)

5. Using only the supplied Ultra ATA cable, you may connect one or two

drives. If you are connecting two or more drives to two Ultra ATA cables, skip

to the next step; otherwise connect the drives as follows:

• When connecting one drive, plug the Ultra ATA cable’s master (black)

connector into it (Figure 5).

• When connecting two drives, connect the Ultra ATA cable’s master (black)

connector to the drive with jumpers set in the master setting; connect the

slave (gray) connector to the drive with jumpers configured in the slave

setting (Figure 5).

6. Using two Ultra ATA cables, you may connect two, three, or four drives;

connect them as follows:

• When connecting two drives, plug the Ultra ATA cables’ master (black)

connectors into the drives (Figure 6).

• When connecting three or four drives, connect the Ultra ATA cables’

master (black) connectors to the drives with jumpers set in the master

setting; connect the slave (gray) connectors to the drives with jumpers set

in the slave setting (Figure 6).

7. Locate the 4-pin power connector plugged into your computer’s existing

hard drive. You should find at least one extra power connector near the exist-

ing drive; if you have installed only one new drive, plug the extra power con-

nector into it. If there are no additional power connectors, you must use

power cable Y-adapters (sold separately). Verify the connectors are plugged

in securely.

8. Route the Ultra ATA cable to the Tempo Trio card; avoid heat sinks and make

sure the cable(s) will not get crushed or pinched by any part of the case

when you reassemble your computer.

9. Attach the Ultra ATA cables’ host (blue) connectors to the Tempo Trio card.

Verify the connector is plugged in securely.

10. Check the cable connections; make sure all cables are properly connected to

the Tempo Trio and the hard drives.

11. Close your computer and carefully replace its cover; be very careful not to

crimp the cables.

Tempo Trio Windows

PCI Host Adapter

Ultra ATA cable

slave

single (or master*)

slave

single (or master*)

- jumpers

*jumpers must be set to master setting when two drives connected to one cable

Figure 6

Tempo Trio Windows

PCI Host Adapter

Ultra ATA cable

slave

single or master*

*jumpers must be set to master setting when two drives connected

- jumpers

Figure 5

Quick Start Guide for Tempo Trio (Windows Version)

Drive Formatting—Windows 98SE and Windows Me

Formatting prepares a hard drive for use by dividing the data area into tracks and

sectors, enabling your computer to store and retrieve data from the drive. This

section describes the process of formatting hard drives connected to the Tempo

Trio, using FDISK on systems running Windows 98SE or Windows Me. The fol-

lowing instructions detail the procedure to create a simple volume (single parti-

tion); if you need to format a drive with multiple partitions, refer to Windows

Help for details. As an alternative, you may choose to format and partition your

hard drive(s) with any software that was included with the drive, following the

included instructions.

1. Turn on your computer and start Windows.

2. From the taskbar, click on Start > Programs > MS-DOS Prompt.

3. At the C:\WINDOWS > prompt, type FDISK.

4. A message will appear stating, “Your computer has a disk larger than 512

MB;” press Enter (Figure 7).

5. From the FDISK Options screen, press 5, and then press Enter.

6. From the Change Current Fixed Disk Drive screen, select the last disk listed

(assuming you’ve connected only one drive at this time), and then press

Enter. Do not accidentally choose an existing formatted drive.

7. When the FDISK Options screen appears again, select “Create DOS Partition

or Logical DOS Drive,” and then press Enter.

8. From the Create DOS Partition or Logical DOS Drive screen, select “Create

Primary DOS Partition,” and then press Enter.

9. As the primary DOS partition is created, the progress will be displayed. When

drive integrity verification is complete, press Enter.

10. The progress will be displayed again, followed by the message “Primary DOS

Partition created, drive letters changed or added;” press Esc to continue.

11. When the next screen appears instructing you to restart your system, press

Esc two times.

12. At the DOS prompt, type EXIT, and then press Enter.

13. From the taskbar, select Start > Shut Down… When the Shut Down window

appears, select Restart, and then click OK.

14. After your computer restarts, double-click My Computer.

15. Right click on the new drive and select “Format…” (Figure 8).

WARNING: Until they have been formatted, hard drives attached to the

Tempo Trio will not appear under My Computer, and can’t be used; this

also applies to drives with data on them, previously used in other computers.

Please be aware that formatting a drive erases any data present.

Figure 7

Figure 8

Andere Handbücher für TEMPO Trio

Inhaltsverzeichnis

Andere Sonnet PCI-Karte Handbücher

Sonnet

Sonnet Crescendo/L2 G3 Bedienungsanleitung

Sonnet

Sonnet TEMPO HD Bedienungsanleitung

Sonnet

Sonnet Tango 3.0 Bedienungsanleitung

Sonnet

Sonnet TEMPO Trio Bedienungsanleitung

Sonnet

Sonnet PRESTO 10GbE 10GBASE-T Bedienungsanleitung

Sonnet

Sonnet ALLEGRO USB 3.0 PCIe Bedienungsanleitung

Sonnet

Sonnet TAT-133 Bedienungsanleitung

Sonnet

Sonnet G10E-1X-E3 Bedienungsanleitung

Sonnet

Sonnet TANGO 2.0 Bedienungsanleitung

Sonnet

Sonnet Solo10G Bedienungsanleitung

Sonnet

Sonnet ALLEGRO USB 2.0 Bedienungsanleitung

Sonnet

Sonnet Tempo SSD Pro 6Gb/s SATA PCIe Drive Card Bedienungsanleitung

Sonnet

Sonnet ARIA EXTREME N PCI Bedienungsanleitung

Sonnet

Sonnet Allegro Pro USB 3.1 PCIe Bedienungsanleitung

Sonnet

Sonnet ARIA EXTREME N PCI Bedienungsanleitung

Sonnet

Sonnet Tempo SATA III 6Gb PCIe 2.0 Bedienungsanleitung

Sonnet

Sonnet TANGO 2.0 Bedienungsanleitung

Sonnet

Sonnet CRESCENDO PCI G3 Bedienungsanleitung

Sonnet

Sonnet Crescendo/PCI Betriebsanleitung

Sonnet

Sonnet M.2 4x4 PCIe Card Bedienungsanleitung

Sonnet

Sonnet Tempo SSD Pro 6Gb/s SATA PCIe Drive Card Bedienungsanleitung

Sonnet

Sonnet ALLEGRO FW800 Bedienungsanleitung

Sonnet

Sonnet ALLEGRO FW400 PCIe Bedienungsanleitung

Sonnet

Sonnet M.2 Bedienungsanleitung

Beliebte PCI-Karte Handbücher anderer Marken

ERMA

ERMA SSI 1417 Bedienungsanleitung

SIIG

SIIG CyberSerial Dual PCI Montageanleitung

I-Bus

I-Bus IBC2602 Bedienungsanleitung

Exsys

Exsys EX-60102 Bedienungsanleitung

Chelsio Communications

Chelsio Communications T5 Series Bedienungsanleitung

Conrad Electronic

Conrad Electronic 97 46 71 Bedienungsanleitung

Micro Innovations

Micro Innovations USB650A Bedienungsanleitung

KTI Networks

KTI Networks KF-310 Bedienungsanleitung

Asus

Asus SpaceLink WL230 Bedienungsanleitung

SIIG

SIIG SC2475 Bedienungsanleitung

TRENDnet

TRENDnet TEW-703PI Bedienungsanleitung

Belkin

Belkin F5D7000F Bedienungsanleitung

Pericom

Pericom PI7C7100 Bedienungsanleitung

ADLINK Technology

ADLINK Technology cPCI-3548 Bedienungsanleitung

Digium

Digium TE200 Series Bedienungsanleitung

Allo.com

Allo.com 2nd Gen E1/T1/J1 Bedienungsanleitung

Western Digital

Western Digital FireWire PCI Adapter Bedienungsanleitung

Pyle

Pyle Gamelink PLINK1 Bedienungsanleitung