Speco D8WRSM Bedienungsanleitung

Product: D8WRSPMQB2 AI- D8WRSPMQB2 Rev a

4/22/14 Page 1 of 20

Speco Technologies Confidential 200 New Highway, Amityville NY 11701

Assembly Instruction

AI – D8WRSMPMQB2

Description: D8WRSM, D16WRSM

Product Code(s): TBD

Equipment #1 Size Phillips head drill, Flat head screwdriver,

Required 3/16” hex head driver, ¼” hex head driver

Associated

Documents:

Eng Approved:

Date:

Alt Approved:

Date:

REVISION HISTORY

DATE INITIAL REASON FOR CHANGE REV.

4/22/14

5/23/14

•

New Document

Changed colors of power cable

Product: AI- D8WRSPMQB2 AI- D8WRSPMQB2 Rev a

4/22/14 Page 2 of 20

Speco Technologies Confidential 200 New Highway, Amityville NY 11701

Equipment Required:

10mm open end wrench

10 mm nutdriver

Lamp Cable Assy

Sensor assembly cable

Power cable assy – (see image below)

drill w/ 5/16” drill bit

conical washer

ruler

heat gun

1/8” shrink tubing

Cable Assemblies Required

Refer to Photo 1 on the following page. Mask the case and mark the drill

locations. The holes will be drilled on the door hinge side of the wall mount

and at the specific locations

5.25” and 6.00” from the base.

Use a starter drill such as 1/8”. Final drill size for both holes is 5/16”.

Product: D8WRSPMQB2 AI- D8WRSPMQB2 Rev a

4/22/14

Page 3 of 20

Speco Technologies Confidential 200 New Highway, Amityville NY 11701

Drill Locations Adding the hardware

Connect the Lamp assembly and the sensor switch assembly to the

chassis with the supplied hardware. Note that the switch assembly gets the

conical washer as shown. Below are the 2 cable assemblies mounted to

the chassis (inside).

Product: D8WRSPMQB2 AI- D8WRSPMQB2 Rev a

4/22/14

Page 4 of 20

Speco Technologies Confidential 200 New Highway, Amityville NY 11701

Slide a 1/8” pre-cut shrink tubing over the red wire of the Power Cable.

Solder this wire to the gold terminal post on the Lamp Cable led. Heat the

shrink tubing with the heat gun.

Add a cable anchor to the inside chassis as shown.

Photo right, tie assemblies cable in a neat bundle and secure with a tywrap.

Embossed +

Product: D8WRSPMQB2 AI- D8WRSPMQB2 Rev a

4/22/14

Page 5 of 20

Speco Technologies Confidential 200 New Highway, Amityville NY 11701

The photo above shows the 2 cable assemblies in a bundle.

Product: D8WRSPMQB2 AI- D8WRSPMQB2 Rev a

4/22/14

Page 6 of 20

Speco Technologies Confidential 200 New Highway, Amityville NY 11701

2.0 - Pre Assembly

1) Attach brackets to the HDD using four DVRWM632SCREW (No ring permitted on screw)

2) Attach the control board to the painted side of WRSMPlate using two 2-56 screws

(90272A081), two 2-56 nuts (90480A003) and two bumpers (9540K11). Place the bumper

between the board and the plate. The nut should be on the plate. The wired side should be

at the bottom of the plate near the tabs.

Repeat on other side.

Product: D8WRSPMQB2 AI- D8WRSPMQB2 Rev a

4/22/14

Page 7 of 20

Speco Technologies Confidential 200 New Highway, Amityville NY 11701

3) Attach the Monitor board to the unpainted side of the WRSMPlate using two 2-56 screws

(90272A081), two 2-56 nuts (90480A003) and two bumpers (9540K11). Place the bumper

between the board and the plate as shown below. The nut should be on the board.

4) Connect the power board cable and the video cable to the monitor board

5) Release the ribbon from the back of the monitor and place the power connector through the

hole in the WRSMPlate.

Product: D8WRSPMQB2 AI- D8WRSPMQB2 Rev a

4/22/14

Page 8 of 20

Speco Technologies Confidential 200 New Highway, Amityville NY 11701

6) Slide the monitor into the tabs and lock down using the clip. Attach the clip with a 4-40

screw (90272A106) and a 4-40 locknut (90633A05).

7) For the new WRSMPLATE, add small piece of doubled sided tape to lower part of the

monitor side and below one clip.

8) Connect the monitor power connector to the monitor board

9) Attach the ribbon to the monitor board by releasing the clip and inserting the ribbon. Be

sure not to crease the ribbon. Once inserted lock in by pressing the clips back in.

Product: D8WRSPMQB2 AI- D8WRSPMQB2 Rev a

4/22/14

Page 9 of 20

Speco Technologies Confidential 200 New Highway, Amityville NY 11701

10) Group the cables and wire tie down using the open hole on the monitor board as shown

below.

Product: D8WRSPMQB2 AI- D8WRSPMQB2 Rev a

4/22/14

Page 10 of 20

Speco Technologies Confidential 200 New Highway, Amityville NY 11701

Section 3.0 - Main Assembly

Box Breakdown:

1) Place the WM Housing in front of you and tighten the nylon screw (93135A144) into the 3

pems which will not be utilized during the build. See below.

HDD

Monitor

Main Board

IR Board

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Speco DVR Handbücher

Speco

Speco LS16 Technisches Handbuch

Speco

Speco D8HS2TB Bedienungsanleitung

Speco

Speco DVR-X4/IP Bedienungsanleitung

Speco

Speco D4VS Gebrauchsanweisung

Speco

Speco DVR-4TL/160* Bedienungsanleitung

Speco

Speco N8NXL Bedienungsanleitung

Speco

Speco DVR-T4IP Bedienungsanleitung

Speco

Speco DVR82HD Bedienungsanleitung

Speco

Speco CS4 Technisches Handbuch

Speco

Speco N8NRE Bedienungsanleitung

Speco

Speco H.264 4-Channel Mobile D4M Bedienungsanleitung

Speco

Speco CS16 Technisches Handbuch

Speco

Speco DVR-4TH Series Bedienungsanleitung

Speco

Speco D12LX Technisches Handbuch

Speco

Speco H16HRL Bedienungsanleitung

Speco

Speco DxVS Series Bedienungsanleitung

Speco

Speco DVR-4TN Series Bedienungsanleitung

Speco

Speco DVR-16TS/750 Bedienungsanleitung

Speco

Speco D16CS Bedienungsanleitung

Speco

Speco 16WM Bedienungsanleitung

Speco

Speco D4VT Bedienungsanleitung

Speco

Speco DVRM42 Bedienungsanleitung

Speco

Speco D4VX Bedienungsanleitung

Speco

Speco D8RS Bedienungsanleitung

Beliebte DVR Handbücher anderer Marken

FLIR

FLIR M3100E Series Bedienungsanleitung

VTRACKPRO

VTRACKPRO FPRO300 Bedienungsanleitung

Swann

Swann NVR-7085 models Bedienungsanleitung

XtendLan

XtendLan DVR-1670C Bedienungsanleitung

urmet domus

urmet domus 1093/004AHD Bedienungsanleitung

Holux

Holux M1 Bedienungsanleitung

CMOS DOTCOM

CMOS DOTCOM ANX-1670 Bedienungsanleitung

Whistler

Whistler D16VRS Bedienungsanleitung

Defender Security

Defender Security 82-20235 Bedienungsanleitung

MISUMI

MISUMI MP-WF100M Bedienungsanleitung

UST

UST DDR-E04AA Gebrauchsanweisung

Consolidated

Consolidated Digital Video Recorder Bedienungsanleitung

Mace

Mace DVR0404RW Kurzanleitung

RCA

RCA RTD315W Bedienungsanleitung

FSM

FSM Colibri Grande PRO Bedienungsanleitung

Hauppauge

Hauppauge HD PVR 2 Bedienungsanleitung

Identivision

Identivision ICR-PH161i PIONEER Bedienungsanleitung

DIGIFUSION

DIGIFUSION FVRT150 Bedienungsanleitung