Sper scientific 840065 Bedienungsanleitung

Wide Range Pressure Meter

840065

Instruction Manual

2 3

Wide Range Pressure Meter - 840065

Printed in the USA

The contents of this manual may not be reproduced or transmitted

in any form or by any means electronic, mechanical, or other

means that do not yet exist or may be developed, including

photocopying, recording, or any information storage and retrieval

system without the express permission from Sper Scientic.

INTRODUCTION .....................................3

PANEL DESCRIPTION ................................3

OPERATING INSTRUCTIONS...........................4

SENSOR TYPES ...................................4

CHANGING THE SENSOR ...........................4

MEASURING PROCEDURES.........................4

DATA HOLD & DATA RECORD ........................5

MEASURING CONSIDERATIONS .....................5

AUTO POWER DISABLE.............................5

CALIBRATION .......................................6

BATTERY REPLACEMENT .............................6

SPECIFICATIONS ....................................7

WARRANTY.........................................8

TABLE OF CONTENTS

INTRODUCTION

This unit covers a wide pressure range, 0 to 725 PSI, not usually

found in a single meter and is compatible with both liquids and

gases. Useful in measuring pneumatic pressure, automobile

engine vacuum pressure, super heat measurements, hydraulic

servo controls, refrigeration, air conditioning, and food processing.

Features eight units of measure (Bar, Psi, Kg/cm mm/1meter/H20,

inch/H20, Atmosphere), min-max, hold, and auto power o󰀨.

PANEL DESCRIPTION

1. Pressure Sensor

Socket & Plug

2. Display

3. Power Button

4. Hold Button

5. Sensor Type Selector

6. Max/Min Button

7. Unit Button

8. Zero Button

9. Pressure Sensor

Main Housing

10. Pressure Sensor

Port Connector

11. Battery Cover (on back)

4 5

OPERATING INSTRUCTIONS

Sensor Types

The meter works with optional pressure sensors.

When changing the sensor, re-calibration is not required.

The optional pressure sensor are:

• 2 Bar pressure sensor

• 5 Bar pressure sensor

• 10 Bar pressure sensor

• 20 Bar pressure sensor

• 50 Bar pressure sensor

• 100 Bar pressure sensor

• 200 Bar pressure sensor

Changing the Sensor

1. Turn the meter o󰀨.

2. Push and hold the following 3 buttons at the same time:

HOLD Button, MAX/MIN Button, SENSOR TYPE Button

3. Continue to hold the 3 buttons, while pushing the POWER

Button. Release the buttons and the display will indicate the

previous sensor type.

4. Push the SENSOR TYPE Button to select the sensor (2, 5, 10,

20, 50, 100, or 200 Bar). When the display indicates the desired

sensor, push the Zero button. The new sensor type will be

stored in memory, even after the unit has been turned o󰀨.

5. Turn o󰀨 the meter. This completes the sensor selection.

Measuring Procedures

1. Connect the Pressure Sensor Plug to the meter’s Sensor

Input Socket.

2. Press the POWER Button.

3. Press the SENSOR TYPE Button to check that the meter’s

sensor type is correct.

4. Press the UNIT Button to select the desired unit of measure:

Bar, Psi, Kg/cm2, mm/Hg, inch/Hg, meter/H20, inch/H20, or

Atmosphere.

5. Press the ZERO Button and the display reading will show zero.

6. Attach the Pressure Sensor Port Connector to the object to

be measured.

7. Apply pressure and the meter will indicate the pressure value.

Data Hold

1. Press the HOLD Button during measurement to freeze the

displayed value. “HOLD” is shown on the LCD.

2. Press the HOLD Button a second time to resume measurement.

Data Record (Maximum/Minimum reading)

The Data Record function displays the maximum and minimum

readings. To start the Data Record function, press the MAX/MIN

Button once. The LCD display will indicate “REC.” Press the MAX/

MIN Button again and the “Max” symbol (along with the maximum

value) will appear on the LCD display. Press the MAX/MIN Button

a third time and the “Min” symbol (along with the minimum value)

will appear on the display. To exit the memory record function,

press and hold the MAX/MIN Button for approximately 2 seconds.

The display will revert back to the current reading.

Measuring Procedures Overview

1. Connect the Sensor Plug to the meter’s Input Socket

2. Turn on the meter

3. Select the display unit.

4. Zero the meter by pressing the ZERO Button.

5. Connect the pressure sensor to the object being measured.

6. Apply pressure and meter will display the pressure value.

Measuring Considerations

• The sensor diaphragm can be damaged by solid or sharp

objects. Never insert objects into the inlet port.

• The pressure sensor operates with industrial gases and liquids

that are compatible with 316 stainless steel or ceramic materials.

To determine the compatibility of a liquid or gas, refer to

manufacture’s specication.

Auto Power Disable

This unit has a built-in Auto Power O󰀨 function to prolong battery life.

The meter will shut o󰀨 automatically if no buttons are pressed within

10 minutes. To deactivate this feature, select the memory record

function during measurement, by pressing the MAX/MIN Button.

6 7

CALIBRATION

Generally, it is not necessary to perform calibrations on the

pressure meter or the external pressure sensor. Each unit is

preadjusted and calibrated.

Zero Calibration

After a long period of operation or due to the environment, the zero

and gain (span) may drift. To ensure an accurate reading, perform

a Zero Calibration as follows:

1. Connect the pressure sensor and shut on the meter.

2. Press and hold both the MAX/MIN Button and the HOLD Button.

The zero value will be displayed in both large and small digits.

3. Continue pressing the MAX/MIN and HOLD Buttons and press

the ZERO Button. The display will ash once and return to zero.

4. Release all three buttons and the new zero value will be stored.

Gain Calibration (Span Adjust)

Turn on the meter and allow it to warm up for two minutes.

Push the

ZERO

Button.

Connect the pressure regulator to a nitrogen bottle and the

reference gauge to the pressure regulator.

Press and hold both the

MAX/MIN

Button and the

HOLD

Button.

Results will be displayed in both the large and the small digits.

5. Continue pressing the

MAX/MIN

and

HOLD

Buttons and press

the

SENSOR TYPE

Button once, to add one count to the small

digit value.

6. Press the

UNIT

Button once to decrease the small digit value by

one count.

7. When the desired value is reached (for example 9.00), release

the

HOLD

and

MAX/MIN

Buttons. The display will ash. Push

the

SENSOR TYPE

Button within 5 seconds. The new gain

value will be stored in the unit.

BATTERY REPLACEMENT

When the top left corner of LCD display indicates “LBT,” it is time

to replace the battery. Accurate readings may be taken for several

hours after the low battery indicator appears. Open the battery

cover, install a fresh 9V battery and replace the cover.

Transducer 840066 840067 840068 840069 840070

Max

Range Res. Max

Range Res.

Bar 2 0.002 50.005 10 0.01 20 0.02 50 0.05

PSI 29 0.02 72.5 0.1 145 0.2 290 0.2 725 1

Kg cm22.040 0.002 5.095 0.005 10.19 0.01 20.40 0.02 50.95 0.05

mm Hg 1500 2 3750 5 7500 10 15000 20 37500 50

In Hg 59.05 0.05 147.6 0.1 295.2 0.2 590.5 0.5 1476 1

Meter H2O20.40 0.02 50.95 0.05 101.9 0.1 204.0 0.2 509.5 0.5

In H2O 802 1 2006 2 4010 5 8020 10 20050 20

Atmospheres 1.974 0.002 4.935 0.005 9.87 0.01 19.74 0.02 49.35 0.05

SPECIFICATIONS - TRANSDUCERS

SPECIFICATIONS - METER

Circuit Microprocessor LSI circuit.

Sensor type

Works with optional 2, 5, 10, 20, 50, 100, 200 bar

sensor, new calibration is not necessary when the

sensor is changed.

Measuring units Bar, Psi, Kg/cm2, mm/Hg, inch/Hg, meter/H2O,

inch/H2O Atmosphere.

Accuracy ± 0.5% + 1d, within 23°C ± 5°C

Zero adjust Push button on the front panel.

Span adjust Push button gain adjustment for precise calibration.

Input signal

from sensor DC 100 mV for full scale.

Data output RS 232 PC serial interface.

Sampling time Approx. 0.8 second.

Operating Temp. 0 to 50°C (32 to 122°F), Less than 80% R.H.

Power supply Alkaline or heavy duty type DC 9V battery, 006P,

MN1604 (PP3) or equivalent.

Power current Approx. DC 7.0 mA.

Dimensions 7" × 3" × 1½" (178 × 76 × 38 mm)

Weight 13 oz (369 g)

8 PB

WARRANTY

Sper Scientic warrants this product against defects in materials

and workmanship for a period of one (1) year from the date of

purchase, and agrees to repair or replace any defective unit

without charge. If your model has since been discontinued, an

equivalent Sper Scientic product will be substituted if available.

This warranty does not cover probes, batteries, battery leakage,

or damage resulting from accident, tampering, misuse, or abuse of

the product. Opening the meter to expose its electronics will break

the waterproof seal and void the warranty.

To obtain warranty service, ship the unit postage prepaid to:

SPER SCIENTIFIC LTD.

8281 East Evans Road, Suite #103

Scottsdale, AZ 85260

The defective unit must be accompanied by a description of the

problem and your return address. Register your product online at

www.sperwarranty.com within 10 days of purchase.

Rev 3/8/2018

Andere Handbücher für 840065

Inhaltsverzeichnis

Andere Sper scientific Messgerät Handbücher

Sper scientific

Sper scientific 840081 Bedienungsanleitung

Sper scientific

Sper scientific 850014 Bedienungsanleitung

Sper scientific

Sper scientific 850068 Bedienungsanleitung

Sper scientific

Sper scientific 840005 Bedienungsanleitung

Sper scientific

Sper scientific 840023 Bedienungsanleitung

Sper scientific

Sper scientific 300005 Bedienungsanleitung

Sper scientific

Sper scientific 300033 Bedienungsanleitung

Sper scientific

Sper scientific 300001 Bedienungsanleitung

Sper scientific

Sper scientific 840005 Bedienungsanleitung

Sper scientific

Sper scientific 840020 Bedienungsanleitung

Sper scientific

Sper scientific 900030 Bedienungsanleitung

Sper scientific

Sper scientific 850024 Bedienungsanleitung

Sper scientific

Sper scientific 800015 Bedienungsanleitung

Sper scientific

Sper scientific 850025 Bedienungsanleitung

Sper scientific

Sper scientific 800048 Bedienungsanleitung

Sper scientific

Sper scientific CL-2006 Bedienungsanleitung

Sper scientific

Sper scientific 800050 Bedienungsanleitung

Sper scientific

Sper scientific 801038 Bedienungsanleitung

Sper scientific

Sper scientific 800046 Bedienungsanleitung

Sper scientific

Sper scientific 850001E Bedienungsanleitung

Sper scientific

Sper scientific 840087 Bedienungsanleitung

Sper scientific

Sper scientific 300100 Bedienungsanleitung

Sper scientific

Sper scientific 800015 Bedienungsanleitung

Sper scientific

Sper scientific 800058 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Keysight

Keysight M8290A Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung