Spirit CT850 ENT Bedienungsanleitung

T850 ENT Treadmill

OWNER’S MANUA

Please carefully read this entiremanual before operating your

new treadmill

-1-

Important Safety Instructions……………………………………………………………………… 2

Important Electrical Information…………………………………………………………………… 3

Important Operation Instructions………………………………………………………………….. 4

Assembly instructions………………………………………………………………………………. 6

Operation of Your New Treadmill…………………………………………………………………..11

Target Heart Rate…………………………………………………………………………………... 28

Using a Heart Rate Transmitter…………………………………………………………………… 29

Heart Rate Control………………………………………………………………………………...... 30

General Maintenance…………………………………………………………………………….......31

Exploded View Diagram and Parts List………………………………………………..……………33

ST8100-WT003_1509A

Table of Contents

-2-

WARNING - Read all instructions before using this appliance.

DANGER - To reduce the risk of electric shock disconnect your SPIRIT treadmill from the

electrical outlet prior to cleaning and/or service work.

WARNING - To reduce the risk of burns, fire, electric shock, or injury to persons, install

the treadmill on a flat level surface with access to a 230-volt AC, 10-Amp. grounded outlet.

With only the treadmill plugged into the circuit.

DO NOT USE AN EXTENSION CORD UNLESS IT IS 14AWG OR LARGER, WITH ONLY ONE

OUTLET ON THE END. The treadmill should be the only appliance in the electrical circuit. DO

NOT ATTEMPT TO DISABLE THE GROUNDED PLUG BY USING IMPROPER ADAPTERS, OR IN

ANY WAY MODIFY THE CORD SET. A serious shock or fire hazard may result along with

computer malfunctions.

■Do not operate treadmill on deeply padded, plush or shag carpet. Damage to both carpet and

treadmill may result.

■Do not block the rear of the treadmill. Provide a minimum of 1 meter clearance between the

rear of the treadmill and any fixed object.

■Keep children away from the treadmill. There are obvious pinch points and other caution

areas that can cause harm.

■Keep hands away from all moving parts.

■Never operate the treadmill if it has a damaged cord or plug. If the treadmill is not working

properly, call your dealer.

■Keep the mains cord away from heated surfaces.

■Do not operate where aerosol spray products are being used or where oxygen is being

administered. Sparks from the motor may ignite a highly gaseous environment.

■Never drop or insert any object into any openings.

■Do not use outdoors.

■To disconnect, turn all controls to the off position, remove tether cord, then remove the

plug from the outlet.

■Do not attempt to use your treadmill for any purpose other than for the purpose it is intended.

■The pulse sensors are not medical devices. Various factors, including the user’s movement,

may affect the accuracy of heart rate readings. The pulse sensors are intended only as

exercise aids in determining heart rate trends in general.

■Use handrails provided; they are for your safety.

■Wear proper shoes. High heels, dress shoes, sandals or bare feet are not suitable for use on

your treadmill. Quality athletic shoes are recommended to avoid leg fatigue.

■This appliance is not intended for use by persons (including children) with reduced physical,

sensory or mental capabilities, or lack of experience and knowledge, unless they have been

given supervision or instruction concerning use of the appliance by a person responsible for

their safety.

■Do not modify the plug provided with the product if it will not fit the outlet; have a proper outlet

installed by a qualified electrician.

Remove tether cord after use to prevent unauthorized treadmill operation.

SAVE THESE INSTRUCTIONS - THINK SAFETY!

Important Safety Instructions

-3-

WARNING!

NEVER use a RCD - Residual Current Device (U.S. ver.= GFCI) - wall outlet with this treadmill.

As with any appliance with a large motor, the RCD/GFCI will trip often. Route the power mains

cord away from any moving part of the treadmill including the elevation mechanism and

transport wheels.

NEVER remove any cover without first disconnecting AC power. If voltage varies by ten percent (10%)

or more, the performance of your treadmill may be affected. Such conditions are not covered

under your warranty. If you suspect the voltage is low, contact your local power company or a

licensed electrician for proper testing.

NEVER expose this treadmill to rain or moisture. This product is NOT designed for use outdoors,

near a pool or spa, or in any other high humidity environment. The temperature specification is 40

degrees c, and humidity is 95%, non-condensing (no water drops forming on surfaces).

Circuit breakers: Some circuit breakers used in homes are not rated for high inrush currents that can

occur when a treadmill is first turned on or even during normal use. If your treadmill is tripping the

circuit breaker (even though it is the proper current rating and the treadmill is the only appliance on

the circuit) but the circuit breaker on the treadmill itself does not trip, you will need to replace the

breaker with a high inrush type. This is not a warranty defect. This is a condition we as a

manufacture have no ability to control. This part is available through most electrical supply stores.

This product must be grounded. If the treadmill’s electrical system should malfunction or

breakdown grounding provides a path of least resistance for electric current, reducing the risk of

electric shock. This product is equipped with a cord having an equipment-grounding plug. The plug

must be plugged into an appropriate outlet that is properly installed and grounded in accordance

with all local codes and ordinances.

DANGER - Improper connection of the equipment-grounding conductor can result in a risk

of electric shock. Check with a qualified electrician or serviceman if you are in doubt as to

whether the product is properly grounded. Do not modify the plug provided with the

product if it will not fit the outlet; have a proper outlet installed by a qualified electrician.

This product is for use on a nominal 230-volt circuit, and has a grounding plug that looks like the

plug illustrated below. A temporary adapter that looks like the adapter illustrated below may be

used to connect this plug to a 2-pole receptacle as shown below if a properly grounded outlet is

not available. The temporary adapter should be used only until a properly grounded outlet, (shown

below) can be installed by a qualified electrician. The green colored rigid ear-lug, or the like,

extending from the adapter, must be connected to a permanent ground such as a properly

grounded outlet box cover. Whenever the adapter is used, it must be held in place by a metal

screw.

Important Electrical Information

Grounding Instructions

-4-

●NEVER operate this treadmill without reading and completely understanding the results of any

operational change you request from the computer.

●Understand that changes in speed and incline do not occur immediately. Set your desired

speed on the computer console and release the adjustment key. The computer will obey the

command gradually.

●NEVER use your treadmill during an electrical storm. Surges may occur in your household

power supply that could damage treadmill components.

●Use caution while participating in other activities while walking on your treadmill; such as

watching television, reading, etc. These distractions may cause you to lose balance or stray

from walking in the center of the belt; which may result in serious injury.

●NEVER mount or dismount the treadmill while the belt is moving. SPIRIT treadmills start with at a

very low speed and it is unnecessary to straddle the belt during start up. Simply standing on the

belt during slow acceleration is proper after you have learned to operate the unit.

Always hold on to a handrail or hand bar while making control changes (incline, speed, etc.).

Do not use excessive pressure on console control keys. They are precision set to function

properly with little finger pressure. Pushing harder is not going to make the unit go faster or

slower. If you feel the buttons are not functioning properly with normal pressure contact your

SPIRIT dealer.

A safety tether cord is provided with this unit. It is a simple magnetic design that should be used

at all times. It is for your safety should you fall or move too far back on the tread-belt.

Pulling this safety tether cord will stop tread-belt movement.

To Use:

1. Place the magnet into position on the console control head. Your treadmill will not start and

operate without this.

2. Fasten the plastic clip onto your clothing securely to assure good holding power. Note: The

magnet has strong enough power to minimize accidental, unexpected stopping. The clip

should be attached securely to make certain it does not come off. Be familiar with its function

and limitations. The treadmill will stop, depending on speed, with a one to two step coast

anytime the magnet is pulled off the console. Use the red Stop / Pause switch in normal

operation.

Safety Tether Cord

Important Operation Instructions

-5-

Assembly Pack Check List

Step1

#117 - 3/8" x16.5 x2.0T x4H

Split Washer (10 pcs)

#144 - 3/8”-16 x 3”

Button Head Socket Bolt (10 pcs)

#134 - M5 x 12mm

Phillips Head Screw (4 pcs)

#116 -ψ3/8" x 35 x 2T

Flat Washer (10 pcs)

Step2

#134 - M5 x 12mm

Phillips Head Screw (4 pcs)

#125 -ψ3/8" x25 x2T

Flat Washer (6 pcs)

Step3

#117 - 3/8" x16.5 x2.0T x4H

Split Washer (6 pcs)

#145 – 3/8”-16 x3/4”

Button Head Socket Bolt (6 pcs)

#146 – M8 x1.25x12mm

Socket Head Cap Bolt (6 pcs)

Step4

#162 - 3/8" ×1-3/4"_Button

Head Socket Bolt (2 pcs)

#163 - 10 × 23 × 1.5T

Curved Wash (2 pcs)

#117 -3/8" x16.5×2.0×4H

Split Washer (2 pcs)

-6-

Step 1: Uprights

The right upright (34) is with preinstalled lower computer cable (42)、TV Signal Cable(171)、

Console Power Cord(173)、network W/Cable(175)、CSAFE W/Cable(177)、HDMI Cable(181)，

To install uprights on the frame base, special care must be taken not to pinch the computer

cable between the upright and frame base. Use first 3/8"-16 × 3"_Button Head Socket Bolt (144)

together with 3/8'' × 16.5 × 2.0 × 4H_Split Washer (117), and 3/8" × 35 × 2T_Flat Washer (116)

through the top hole in the retaining plate (98), and corresponding top hole in the upright tube,

and screw into the base frame. Now install the other four bolts 3/8"-16 × 3"_Button Head

Socket Bolt (144) together with 3/8'' × 16.5 × 2.0 × 4H_Split Washer (117), and 3/8" × 35 ×

2T_Flat Washer (116) and tighten all five bolts up.

Same as the above step to install left upright (33).

Use four M5 × 12L Phillips Head Screws (134) install left and right motor base cap (26, 27)

Assembly Instructions

-7-

Step 2: Installing the console

Connect upper computer cable (41), TV Signal Cable(170), Console Power Cord(172) , etwork

W/Cable(174)、CSAFE W/Cable(176)、HDMI Cable(180)、Handpulse Wire Upper(39)(40) and

Ground Wire(178) all connect to the board on back of the console (28).

Use four M5 × 12L Phillips Head Screws (134) to secure console assembly onto the console

support (5).

-8-

Step 3: Installing console onto uprights

Use six M8 × 1.25 × 12L Socket Head Cap Bolts (146) to secure the console on interface

mounting bracket on uprights (3, 4).

Connect upper computer cable (41) and lower computer cable (42), upper TV Signal Cable

(170) and lower TV Signal Cable (171), upper Console Power Cord(172) and lower Console

Power Cord (173)、upper network W/Cable (174)and lower network W/Cable (175)、upper

CSAFE W/Cable (176)and lower CSAFE W/Cable (177)、upper HDMI Cable (180) and lower

HDMI Cable (181)

Use six 3/8"-16 × 3/4" Button Head Socket Bolts (145), together with six 3/8'' × 16.5 × 2.0 × 4H

Split Washers (117) and six 3/8" × 25 × 2T Flat Washers (125) on top of uprights.

Be careful not to pinch the computer cable.

-9-

Step 4: Upright reinforcement

Tighten one 3/8" -16 x 1-3/4" Button Head Socket Bolt(162), together with one 3/8" x16.5 x2T x4H

Split Washer (117) and one 10 x23 x1.5T Curved Washer(163) through Upright (R) (34).

Same way for Upright (L) (33).

Andere Handbücher für CT850 ENT

Inhaltsverzeichnis

Andere Spirit Tretmühle Handbücher

Spirit

Spirit Treadmill Bedienungsanleitung

Spirit

Spirit 1622768 Bedienungsanleitung

Spirit

Spirit XT385 Bedienungsanleitung

Spirit

Spirit XT175 Bedienungsanleitung

Spirit

Spirit 1622775 Bedienungsanleitung

Spirit

Spirit XT285 Bedienungsanleitung

Spirit

Spirit SR225 Systemhandbuch

Spirit

Spirit XT185 Bedienungsanleitung

Spirit

Spirit 1622778 Bedienungsanleitung

Spirit

Spirit Z88 Bedienungsanleitung

Spirit

Spirit F7500 Bedienungsanleitung

Spirit

Spirit CT 800 Bedienungsanleitung

Spirit

Spirit XT185 Bedienungsanleitung

Spirit

Spirit XT685 Bedienungsanleitung

Spirit

Spirit XT485ENT Bedienungsanleitung

Spirit

Spirit XT685 Bedienungsanleitung

Spirit

Spirit XT285 Bedienungsanleitung

Spirit

Spirit Z700-A82 Bedienungsanleitung

Spirit

Spirit XT 9 Bedienungsanleitung

Spirit

Spirit Z900 Bedienungsanleitung

Spirit

Spirit XT8 Bedienungsanleitung

Spirit

Spirit Esprit CT80 Bedienungsanleitung

Spirit

Spirit Z100 Bedienungsanleitung

Spirit

Spirit XT385 Bedienungsanleitung

Beliebte Tretmühle Handbücher anderer Marken

Treadly

Treadly TREADLY 2 Bedienungsanleitung

HEALTH ONE

HEALTH ONE Walk Ro Bedienungsanleitung

NordicTrack

NordicTrack T7.5 S Bedienungsanleitung

Gold's Gym

Gold's Gym ADVANTAGE GGTL12920 Bedienungsanleitung

Merax

Merax MS282992 Bedienungsanleitung

FYTTER

FYTTER RU-2SX Bedienungsanleitung

Precor

Precor 903 Bedienungsanleitung

FitLogic

FitLogic freewill d225 Bedienungsanleitung

HOP-SPORT

HOP-SPORT ESTIMA HS-3200LB Bedienungsanleitung

Horizon Fitness

Horizon Fitness Adventure 5 Plus Bedienungsanleitung

Stamia

Stamia InMotion II Bedienungsanleitung

Smooth Fitness

Smooth Fitness EVO 3i Bedienungsanleitung

NordicTrack

NordicTrack NETL81810.0 Bedienungsanleitung

Schwinn

Schwinn 830/Journey 8.0 Bedienungsanleitung

Keys Fitness

Keys Fitness HealthTrainer HT-740T Bedienungsanleitung

NordicTrack

NordicTrack T 14.0 Treadmill Bedienungsanleitung

Master

Master F22 Bedienungsanleitung

Precor

Precor PRECISION SERIES Technisches Handbuch