Sricam NVS010 Benutzerhandbuch
Wireless NVR
Quick Operation Guide
Applicable to NVS010
V1.0 CN202310
English
1. Connect the host correctly (as shown below)
3. If the camera test screen displays normally, then select the camera installation location
according to the channel corresponding to the screen.
(Tips: It is recommended that the installation location have as few partition walls as possible, and
the network signal is relatively stable within 30 meters of indoor installation)
1
Camera (12V)
NVR power supply(12V/2A)
Router
HDMI or VGA
Monitor (optional)
Mouse (optional)
WiFi
CH1
CH3
CH2
CH4
+2023-10-25 16:45:29
Login
User Name
Tips
Cancel
password
Forget Password?
admin
2. After powering on and waiting for startup to complete, you will see the camera screen on
the host display. (NVR default login password: 888888)
Install wireless NVR
(1) Please use the power adapter provided by the manufacturer to connect
(2) Connect the NVR to the router through a network cable (for local access, please skip this step)
888888
2
If the product you purchased does not come with a hard drive, please purchase a 2.5-inch
hard drive by yourself, 4T is recommended (maximum support is 16T)
Notice:
A: The camera has been paired with the NVR host at the factory, so there is no need to configure WiFi.
B: If you purchase a single product of NVS010 and need to add a camera, please refer to pages 3-4
of the manual.
The hard disk installation method is as shown below:
Note: Please do not connect the NVR to the power supply before installing the hard disk.
(1) Open the hard drive compartment cover from the buckle underneath the hard drive compartment.
(2) Connect a 2.5-inch SATA hard drive to the NVR hard drive interface and fix it on the hard drive
compartment cover with screws.
(3) Fasten the hard drive compartment cover.
2.5”HDD
NVS010 output VGA/HDMI settings
Click the start menu in the lower left corner -> click the normal device icon -> click
"Advanced" -> turn on "HDMI Display"
Warn:
After the HDMI interface is turned on, the current host will no longer be
displayed, and an external monitor must be connected to display it.
NVR installation hard disk
CH1
CH3
CH2
CH4
+2023-10-25 16:45:29
Add IPC
General
Camera
Record
Backup Maintenance
Motion
Ring
Network
HDD
P2P
Playback
Normal settings
Startup Wizard
Advanced
HDMI display
Screen Saver
Log in
X
3
Reset
Note: If the camera does not emit a "beep", "beep", "beep" network configuration prompt after 30 seconds
of power on, please keep the power on and hold the Reset button for 5 seconds. After hearing a long beep,
let go and wait for the camera. Restart.
CH1
CH3
CH2
CH4
+2023-10-25 16:45:29
+
1
+2023-10-25 16:45:29
Added Device List
Index IP address Mac address type operate
1
idle
Add
2
idle
Add
3
idle
Add
4
idle
Add
5
idle
Add
6
idle
Add
7
idle
Add
8
idle
Add
Set up relay wireless status
X
Method 1: Scan the QR code to add
It will take about 30 seconds after the camera is powered on to complete the power-on process.
After hearing the beep, beep, and beep sounds from the camera, do the following:
(1). Click the icon in the lower left corner of the monitoring display
(2). Click "Add" on the right side of the device list, and then select "QR code"
(3). Aim the camera lens at the QR code and keep a distance of 20-60cm. After the camera
recognizes the QR code, the camera emits a "ding" sound, indicating that the network
configuration is successful. After successful pairing, wait a few seconds to see the video in the
preview interface.
How to add a camera
Warn: Do not delete the camera in the added device list. After deletion, you need to pair it again.
X
Search
Select IPC connection method
Tip
Pair QR code
2
Reset
4
+2023-10-25 16:45:29
Available device list
Add IPC
Serial number IP Address Mac Address
1 192.168.1.4 00：2A:2B:FE:55:E0
00：2A:2B:FE:55:ED
00：2A:2B:FE:55:E0
00：2A:2B:FE:55:ED
00：2A:2B:FE:55:E0
00：2A:2B:FE:55:ED
2 192.168.1.6
3 192.168.1.10
4 192.168.1.12
5 192.168.1.15
6 192.168.1.18
Tip: Click the camera IP button in the available devices list to enter the add device page.
Add
X
Cameras in the same local network (support SriHome models with network interfaces) can be
added to the device by searching and adding. Select "Search" -> Select the camera you want to
add in the list of available devices and enter the camera password.
(Default password: 888888) Click Add to confirm.
WIFI
Method 2: Button pairing added
Method 3: Search and add
It will take about 30 seconds after the camera is powered on to complete the power-on process.
After hearing the beep, beep, and beep sounds from the camera, do the following:
+
(1). Click the icon in the lower left corner of the monitoring display
(2). Click "Add" on the right side of the device list, and then select "Pair"
(3). To connect, quickly press the reset button of the camera 5 times for pairing. When the camera
emits a "ding" sound, it indicates that the network configuration is successful. After successful
pairing, wait a few seconds to see the video in the preview interface.
2023-10-25 16:45:29
Index IP address Mac address type operate
Add
Add
Add
Add
Add
Add
Add
Add
Set up relay wireless status
X
Search
Select IPC connection method
Tip
Pair QR code
Added Device List
5
SriHome APP Setup
Step 1. SriHome App Installation
Method 2: Search“SriHome”on Google Play or iOS App Store.
Method 1: Scan the QR code to download “SriHome” App.
Step 2. Register & Login SriHome App
Step 3. Add the Device to App
Device
3-1
Add
Next
N0*******
Input the device’s ID
3-2
Input device name to search device
You can scan the
QR code or input the
Device ID manually
WiFi NVR
ID: N0***********
Password: 888888
RoHS
The label is attached on
the NVR
12
Note: The NVR host must be connected to the Internet for the mobile APP remote
monitoring function to be used.
Android iOS
6
FAQ
Settings
Settings
System
Time Settings
Video Settings
Alarm Settings
Record Settings
Network Settings
Security Settings
Visitors Management
Home
1 2 3
Add share user
User authorization Visitor
Operator
Visitor
Input new user’s APP ID
User Remarks
Share User
Visitors Management
Add
FAQ1: Share the Wireless NVR to other users
To protect the user's privacy, the first user is an administrator by default. Other users
accessing the Wireless NVR need administrator permission, or they cannot login even
with ID and password. The way to get permission is as follows:
2. Access the “SriHome” App, tap Settings -> Visitor Management -> Add.
There are 2 types of permissions:
Operator:
Live video view, set time, alarm, record and network.
Visitor:
Viewing video only in real time
Note: You can find the user's App ID in
App Settings
1. Download SriHome App->Login Account->Add Camera ID
(Prompt no permission, please contact the administrator for authorization)
7
Click the main menu in the lower left corner >Device Maintenance >Restore Default
>Please select the default setting item you want.
FAQ3: If you forget your password, How to retrieve password
Login panel > Forgot password > Click Retrieve password > Check the recovery key on your bound
email account > Enter the key number, and your password will be displayed on the login panel.
FAQ2: If you forget who the administrator is, you can reset and
become a new administrator
CH1
CH3
CH2
CH4
+2023-10-25 16:45:29
Add IPC
General
Camera
Record
Backup Maintenance
Motion
Ring
Network
HDD
P2P
Playback
CH1
CH3
CH2
CH4
+2023-10-25 16:45:29
Add IPC
General
Camera
Record
Backup Maintenance
Motion
Ring
Network
HDD
P2P
Playback
Restore
IP address
System time
Password
Log
Other
X
OK Cancel
Upgrade Source USB
Mac address: 60:08:00:00:3B
Chip information: 714-W1
Series version: 6.3.17.11000000
System Upgrade
Select upgrade file
X
Upgrade
Restore
Reboot
Maintenance
CH1
CH3
CH2
CH4
+2023-10-25 16:45:29
Retrieve password
Random number 43501922
Retrieve password
OK
Recovery key
Select 'Retrieve Password' and check your recovery email
account for the recovery key
X
CH1
CH3
CH2
CH4
+2023-10-25 16:45:29
Retrieve password
Random number 43501922
Retrieve password
OK
Recovery key
****
Password: *******
X
CH1
CH3
CH2
CH4
+2023-10-25 16:45:29
Retrieve password
Random number 43501922
Retrieve password
OK
Recovery key
Select 'Retrieve Password' and check your recovery email
account for the recovery key
X
CH1
CH3
CH2
CH4
+2023-10-25 16:45:29
Login
User Name
Tips
Cancel
password
Forget Password?
admin
888888
Exit
Tip
Send successfully, please confirm the recovery
key in the mobile phone mailbox.
NVR inalámbrico
Guía de operación rápida
Aplicable a NVS010
V1.0 CN202310
Español
1. Conecte el host correctamente (como se muestra a continuación)
3. Si la pantalla de prueba de la cámara se muestra normalmente, seleccione la ubicación de
instalación de la cámara de acuerdo con el canal correspondiente a la pantalla.
(Consejos: se recomienda que la ubicación de instalación tenga la menor cantidad de paredes
divisorias posible y que la señal de la red sea relativamente estable dentro de los 30 metros de la
instalación interior.)
1
Cámara (12V)
Fuente de alimentación NVR (12V/2A)
Enrutador
HDMI o VGA
Monitorear (opcional)
Ratón (opcional)
WiFi
CH1
CH3
CH2
CH4
+2023-10-25 16:45:29
Login
User Name
Tips
Cancel
password
Forget Password?
admin
2. Después de encender y esperar a que se complete el inicio, verá la pantalla de la cámara en
la pantalla del host. (Contraseña de inicio de sesión predeterminada de NVR: 888888)
Instalar NVR inalámbrico
(1) Utilice el adaptador de corriente proporcionado por el fabricante para conectar
(2) Conecte el NVR al enrutador a través de un cable de red (para acceso local, omita este paso)
888888
Inhaltsverzeichnis
Sprachen:
Andere Sricam DVR Handbücher
