ST EVAL-L99MOD5xXP Bedienungsanleitung
Introduction
This document describes the STSW-L99MOD5xXP graphical user interface (GUI) dedicated to set and control the EVAL-
L99MOD5xXP family evaluation kit.
The EVAL-L99MOD5xXP evaluation kit consists in a motherboard and a daughterboard on which the L99MOD5xXP device is
assembled. Both of these evaluation boards provide electronic control modules with enhanced power management
functionalities including a standby mode. These evaluation boards are designed to drive multiple brushed DC motors and
additional loads in high-side configuration, such as bulbs, LEDs or protected supply.
The STSW-L99MOD5xXP has been developed using C++ and works with a motherboard based on an SPC560B microcontroller
which is programmed with a dedicated firmware to drive the specific L99MOD5xXP device assembled on the daughterboard.
How to use the EVAL-L99MOD5xXP evaluation kit
UM2654
User manual
UM2654 - Rev 1 - November 2019
For further information contact your local STMicroelectronics sales office.
www.st.com
1Evaluation kit connection
The following figure shows how to connect the evaluation kit.
Figure 1. Evaluation kit connection
UM2654
Evaluation kit connection
UM2654 - Rev 1 page 2/10
2Evaluation kit installation
To install the evaluation kit, follow the instructions below:
1. Install the VISA and Run-Time Engine drivers on the computer running the demo tool. Run the two
downloaders below from the supplier's website to download and install the drivers:
2. Install the FTDI driver from the supplier's website.
3. Complete the connection as Figure 1. Evaluation kit connection shows, then power on the kit.
4. Run the “L99MOD5x.exe” and select the appropriate device from the list.
5. If you receive a communication error message, select the correct serial port manually according to your
setup.
6. Once the correct serial port is selected, the GUI will return the firmware version message.
UM2654
Evaluation kit installation
UM2654 - Rev 1 page 3/10
3Description of the graphical user interface
The following figures present the main windows of the graphical user interface.
Figure 2. Device selection
Figure 3. Common commands
1. Selection tabs
2. VISA Port: please select the appropriate serial port
3. Check sum mark: in case the checksum is correct, "OK" is displayed; otherwise, the indicator turns red and
"ERROR" is displayed
4. Continue Diagnose: if this option is checked, the GUI reads the status register continuously.
5. Read and Clear (R&C): when you click this button, the GUI will read and clear the status register once.
6. Reset: click this button to restore the GUI to the initial state
7. Stop: click this button to exit the GUI
UM2654
Description of the graphical user interface
UM2654 - Rev 1 page 4/10
Figure 4. Standard control tab
1. OUT Control: half-bridge, high-side outputs control
2. Enable device button
3. Configuration registers settings
4. Diagnostic Status: if any of these states occur, the corresponding status display will become red. Once the
control register changes, the status register and all diagnostic information will be updated once.
UM2654
Description of the graphical user interface
UM2654 - Rev 1 page 5/10
Figure 5. Current monitor and PWM tab
1. Current value display window
2. Current value
3. Current detection select output
4. Current monitor start button
5. Clear window value button
6. PWM configuration: on/off, frequency and duty cycle settings
UM2654
Description of the graphical user interface
UM2654 - Rev 1 page 6/10
1. Status Registers: SR0…SR2: it is possible to read and clear all status registers once or read them
continuously. Once the control register changes, the status register and all diagnostic information will be
updated once.
2. Global Status Regster. this is device-dependant.
3. SPI History: the SPI commands sent to the device are recorded here.
4. Clear History: it clears the SPI history.
5. Continue Diagnose: if this option is checked, the GUI reads the status register continuously.
6. Read and Clear (R&C): when you click this button, the GUI will read and clear the status register once.
UM2654
Description of the graphical user interface
UM2654 - Rev 1 page 8/10
Revision history
Table 1. Document revision history
Date Version Changes
20-Nov-2019 1 First release
UM2654
UM2654 - Rev 1 page 9/10
IMPORTANT NOTICE – PLEASE READ CAREFULLY
STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, enhancements, modifications, and improvements to ST
products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on ST products before placing orders. ST
products are sold pursuant to ST’s terms and conditions of sale in place at the time of order acknowledgement.
Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or the design of
Purchasers’ products.
No license, express or implied, to any intellectual property right is granted by ST herein.
Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product.
ST and the ST logo are trademarks of ST. For additional information about ST trademarks, please refer to www.st.com/trademarks. All other product or service
names are the property of their respective owners.
Information in this document supersedes and replaces information previously supplied in any prior versions of this document.
© 2019 STMicroelectronics – All rights reserved
UM2654
UM2654 - Rev 1 page 10/10
Inhaltsverzeichnis
Andere ST Hauptplatine Handbücher
ST
ST STM3210C-EVAL Bedienungsanleitung
ST
ST STEVAL-IFS002V2 Bedienungsanleitung
ST
ST EVAL-L99ASC03 Bedienungsanleitung
ST
ST SPC572LADPT100S Bedienungsanleitung
ST
ST STM32G4 Nucleo-64 Bedienungsanleitung
ST
ST STEVAL-LVLP01 Bedienungsanleitung
ST
ST STM32H743I-EVAL Bedienungsanleitung
ST
ST UM2414 Bedienungsanleitung
ST
ST AN3954 Montage- und Bedienungsanleitung
ST
ST STMPE801 Bedienungsanleitung
ST
ST STM32100B-EVAL Bedienungsanleitung
ST
ST STEVAL-IDB007V Series Bedienungsanleitung
ST
ST EVAL-L9963E-MCU Bedienungsanleitung
ST
ST PowerSTEP01 EVLPOWERSTEP01 Bedienungsanleitung
ST
ST UM1789 Bedienungsanleitung
ST
ST X-NUCLEO-IDB04A1 Bedienungsanleitung
ST
ST STM32429I-EVAL Bedienungsanleitung
ST
ST STM32F103RET6 Bedienungsanleitung
ST
ST STEVAL-IHM020V1 Bedienungsanleitung
ST
ST STEVAL-STRKT01 Administratorhandbuch
Beliebte Hauptplatine Handbücher anderer Marken
Telit Wireless Solutions
Telit Wireless Solutions SL869-3DR Bedienungsanleitung
Gigabyte
Gigabyte GA-9IVDT Bedienungsanleitung
Texas Instruments
Texas Instruments ADS8372EVM Bedienungsanleitung
Commell
Commell MS-C73 Bedienungsanleitung
IBT Technologies
IBT Technologies MB860 Bedienungsanleitung
Nvidia
Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung
