ST SPC58XXADPT144S REV.B Bedienungsanleitung

Introduction

The SPC58XXADPT144S rev. B evaluation board supports STMicroelectronics SPC58xGxxE5, SPC58xCxxE5 and

SPC58xBxxE5 microcontrollers in eTQFP144 package with exposed pad down.

Figure 1. SPC58XXADPT144S rev. B

Note: Picture not contractual

SPC58XXADPT144S rev. B evaluation board

UM2827

User manual

UM2827 - Rev 1 - February 2021

For further information contact your local STMicroelectronics sales office.

www.st.com

1Overview

The SPC58XXADPT144S rev. B "mini module" is an evaluation board supporting STMicroelectronics

SPC58xGxxE5, SPC58xCxxE5 and SPC58xBxxE5 microcontrollers in eTQFP144 package with exposed pad

down.

The "mini module" is designed to be connected onto the SPC58xxMB motherboard, offering a mechanism for

easy customer evaluation of the supported devices, and to facilitate hardware and software development.

The "mini module" may be used as a stand-alone unit granting access to the MCU, but no access to the I/O pins

as any motherboard peripherals.

The "mini module" is configured by default for SPC58xB and SPC58xC easily supports also SPC58xG by simply

changing the following 3 TH jumper: JR14, JR18 & JR19, with the only drawback that some ports are not

mapped/aligned properly.

Figure 2. Overview of SPC58XXADPT144S rev. B "mini module" - top

UM2827

Overview

UM2827 - Rev 1 page 2/25

Figure 3. Overview of SPC58XXADPT144S rev. B "mini module" - bottom

1.1 Package contents

An SPC58XXADPT144S rev. B adapter package includes the following item:

• SPC58XXADPT144S rev. B "mini module"

1.2 Supported devices

The SPC58XXADPT144S rev. B "mini module" supports the following STMicroelectronics family of

microcontrollers in eTQFP144 package with exposed pad down:

• SPC58xBxxE5

• SPC58xCxxE5

• SPC58xGxxE5

UM2827

Package contents

UM2827 - Rev 1 page 3/25

2License agreement

The packaging of this evaluation board was sealed with a seal stating, " by breaking this seal, you agree to the

terms and conditions of the evaluation board license agreement, the terms and conditions of which are available

at https://www.st.com/resource/en/evaluation_board_terms_of_use/evaluationproductlicenseagreement.pdf ".

Upon breaking the seal, you and STMicroelectronics entered into the evaluation board license agreement, a

copy of which is also enclosed with the evaluation board for convenience.

Attention: This evaluation board only offers limited features for evaluating ST products. It has not been tested for use

with other products and is not suitable for any safety or other commercial or consumer application. This

evaluation board is otherwise provided “AS IS” and STMicroelectronics disclaims all warranties, express or

implied, including the implied warranties of merchantability and fitness for a particular purpose.

UM2827

License agreement

UM2827 - Rev 1 page 4/25

3Handling precautions

Please take care to handle the package contents in a manner such as to prevent electrostatic discharge.

Before the EVB is used or power is applied, please fully read the following sections on how to correctly configure

the board. Failure to correctly configure the board may cause irreparable component, MCU or EVB damage.

UM2827

Handling precautions

UM2827 - Rev 1 page 5/25

4Hardware description

4.1 Hardware features

The SPC58XXADPT144S rev. B "mini module" board has the following features:

• Connector for external power supplies input (5.0 V, 3.3 V, 1.25 V) used in stand-alone mode

• Reset button with driver and led indicator

• Socket for device in eTQFP144 package with exposed pad down

• Debug ports:

– 38-pin Mictor connector for Nexus level 3+

– 14-pin header connector for JTAG port

– 10-pin header connector for JTAG/DigRF port (LFAST)

• 40 Mhz crystal main oscillator with jumpers to optionally disconnect it

• 8 Mhz oscillator with jumpers to optionally disconnect it

• Clock input through SMA connector to optionally disconnect it

• 2 X SAMTEC QSH series, 240 way connector to connect "mini module" to motherboard

4.2 Hardware dimension and PCB component view

The "mini module" has the following dimensions:

• PCB area: 127 mm x 114.3 mm

• Top components height: 16.5 mm max

• Bottom components height: 3.5 mm max

• PCB thickness: 1.6 mm

UM2827

Hardware description

UM2827 - Rev 1 page 6/25

5Power and system configuration

5.1 Power supplies

When the "mini module" is plugged onto the motherboard, power is supplied directly by the motherboard. In this

setup, the external power supply input available on the "mini module" should NOT be used.

When the SPC58XXADPT144S rev.B "mini module" is used as a stand-alone board, external power supplies

must be used (5 V, 3.3 V, 1.25 V).

The following jumpers are used to configure the power supply:

Table 1. Supply related jumpers

Jumper Description Default Position

VDD_HV_ADR_D voltage configuration,

select from 5.0V_LR (linear), 3.3V_SR

(switching) or 5.0V_SR (switching) (used

only for SPC58xGxxE5).

1-2 (5.0V_LR) Figure 4. SPC58XXADPT144S rev. B "mini module" -

top - D3

J3 Jumper to enable the use of supply

3.3V_SR Closed Figure 4. SPC58XXADPT144S rev. B "mini module" -

top - D3

J4 Jumper to enable the use of supply

5.0V_SR Closed Figure 4. SPC58XXADPT144S rev. B "mini module" -

top - D3

J5 Jumper to enable the use of supply

1.25V_SR Closed Figure 4. SPC58XXADPT144S rev. B "mini module" -

top - B4

VDD_HV_ADR_S voltage configuration,

select from 5.0V_LR (linear), 3.3V_SR

(switching) or 5.0V_SR (switching)

1-2 (5.0V_LR) Figure 4. SPC58XXADPT144S rev. B "mini module" -

top - D2

VDD_HV_ADV_S voltage configuration,

select from 5.0V_LR (linear), 3.3V_SR

(switching) or 5.0V_SR (switching)

1-2 (5.0V_LR) Figure 4. SPC58XXADPT144S rev. B "mini module" -

top - D2

J8 VDD_HV_IO_MAIN voltage configuration,

select from 5.0V_SR or 3.3V_SR 1-2 (5.0V_SR) Figure 4. SPC58XXADPT144S rev. B "mini module" -

top - D3

J9 VDD_HV_IO_FLEX voltage configuration,

select from 5.0V_SR or 3.3V_SR 1-2 (5.0V_SR) Figure 4. SPC58XXADPT144S rev. B "mini module" -

top - D3

J10 VDD_LV voltage configuration, select from

1.25V_SR or from ballast circuit 1-2 (1.25V_SR) Figure 4. SPC58XXADPT144S rev. B "mini module" -

top - B4

J11 Ballast supply voltage configuration, select

from VDD_HV_IO_MAIN or from 5.0V_SR 1-2 (5.0V_SR) Figure 4. SPC58XXADPT144S rev. B "mini module" -

top - C4

JP1

VDD_HV_FLA voltage configuration:

connect or disconnect VDD_HV_FLA from

VDD_HV_IO_MAIN

Closed Figure 5. SPC58XXADPT144S rev. B "mini module" -

bottom - C3

UM2827

Power and system configuration

UM2827 - Rev 1 page 7/25

5.2 System clock configuration

The "mini module" supports the usage of crystal clock sources as well as external clock source:

Table 2. Clock configuration jumpers

Jumper Description Default Position

J15 40 MHz crystal clock source enable

for pin EXTAL 1-2 (XT1 pin2) Figure 4. SPC58XXADPT144S rev. B "mini module" - top -

J17 40 MHz crystal clock source enable

for pin XTAL 1-2 (XT1 pin1) Figure 4. SPC58XXADPT144S rev. B "mini module" - top -

J19 Enable 8 MHz oscillator power

supply Open Figure 4. SPC58XXADPT144S rev. B "mini module" - top -

J21 External clock source from 8 MHz

oscillator or SMA connector

1-2 (8 MHz

oscillator)

Figure 4. SPC58XXADPT144S rev. B "mini module" - top -

5.3 Reset circuit

The "mini module" supports different ways to reset the microcontroller.

To use and perform the reset driving there are different jumpers and switches:

Table 3. Reset configuration jumpers

Jumper Description Default Position

SW1 Reset push button Open Figure 4. SPC58XXADPT144S rev. B "mini module" - top - D1

J22

Connect the external reset to the reset

driver for

ESR0 and PORST pins

Close Figure 4. SPC58XXADPT144S rev. B "mini module" - top - D1

J20 Connect the external reset to ESR0 pin Close Figure 4. SPC58XXADPT144S rev. B "mini module" - top - D1

J25 Connect the external reset to PORST pin Close Figure 4. SPC58XXADPT144S rev. B "mini module" - top - D2

UM2827

System clock configuration

UM2827 - Rev 1 page 8/25

5.4 Port configuration

The following jumpers need to configure the ports:

Table 4. Ports related jumpers

Jumper Description Default Position

JP13 TESTMODE settings Close (10 KΩ pull-

down) Figure 4. SPC58XXADPT144S rev. B "mini module" - top - A2

J13

RSTIN configuration

• 1-2: ESR0

• 2-3: PORST

2-3

(PORST) Figure 4. SPC58XXADPT144S rev. B "mini module" - top - B2

JP2

JTAG/DigRF pin 9 configuration

• 1-2: EVTO

• 2-3: ESR0

1-2

(EVTO) Figure 4. SPC58XXADPT144S rev. B "mini module" - top - A3

JP3

PIN26 configuration

• 1-2: PG1

• 2-3: EVTI (SPC582B)

Closed 1-2 Figure 4. SPC58XXADPT144S rev. B "mini module" - top - C2

JP4

EVTI SWITCH configuration

• 1-2: to JP3 (SPC582B)

• 2-3: to JP5 (SPC58xG)

Closed 1-2 Figure 4. SPC58XXADPT144S rev. B "mini module" - top - C3

JP5

PM5/EVTI configuration

• 1-2: PM5

• 2-3: EVTI (SPC58xG)

Closed 1-2 Figure 4. SPC58XXADPT144S rev. B "mini module" - top - C3

JP6

PIN27 configuration

• 1-2: PG2

• 2-3: EVTO (SPC582B)

Closed 1-2 Figure 4. SPC58XXADPT144S rev. B "mini module" - top - C3

JP7

EVTO SWITCH configuration

• 1-2: to JP6 (SPC582B)

• 2-3: to JP8 (SPC58xG)

Closed 1-2 Figure 4. SPC58XXADPT144S rev. B "mini module" - top - C3

JP8

PIN130 configuration

• 1-2: PM6

• 2-3: EVTO (SPC58xG)

Closed 1-2 Figure 4. SPC58XXADPT144S rev. B "mini module" - top - C3

UM2827

Port configuration

UM2827 - Rev 1 page 9/25

5.5 SPC58xG configuration

The following jumpers need to configure the board for support the SPC58xG:

Table 5. SPC58xG configuration related jumpers

Jumper Description Default Position

JR2 Device pin 134 port

configuration

1-2

(closed with PCB trace for connect

pin 134 to PC[13] )

Figure 5. SPC58XXADPT144S rev. B "mini

module" - bottom - B3

JR3 Device pin 133 port

configuration

1-2

(closed with PCB trace for connect

pin 133 to PC[14] )

Figure 5. SPC58XXADPT144S rev. B "mini

module" - bottom - B3

JR4 Device pin 132 port

configuration

1-2

(closed with PCB trace for connect

pin 132 to PC[15] )

Figure 5. SPC58XXADPT144S rev. B "mini

module" - bottom - B3

JR5 Device pin 40 port

configuration

1-2

(closed with PCB trace for connect

pin 40 to PI[7] )

Figure 5. SPC58XXADPT144S rev. B "mini

module" - bottom - B2

JR6 Device pin 34 port

configuration

1-2

(closed with PCB trace for connect

pin 34 to PI[5] )

Figure 5. SPC58XXADPT144S rev. B "mini

module" - bottom - B2

JR7 Device pin 32 port

configuration

1-2

(closed with PCB trace for connect

pin 32 to PI[3] )

Figure 5. SPC58XXADPT144S rev. B "mini

module" - bottom - B2

JR8 Device pin 30 port

configuration

1-2

(closed with PCB trace for connect

pin 30 to PI[1] )

Figure 5. SPC58XXADPT144S rev. B "mini

module" - bottom - B2

JR9 Device pin 20 port

configuration

1-2

(closed with PCB trace for connect

pin 20 to PI[8] )

Figure 5. SPC58XXADPT144S rev. B "mini

module" - bottom - B3

JR10 Device pin 39 port

configuration

1-2

(closed with PCB trace for connect

pin 39 to PI[6] )

Figure 5. SPC58XXADPT144S rev. B "mini

module" - bottom - B2

JR11 Device pin 33 port

configuration

1-2

(closed with PCB trace for connect

pin 33 to PI[4] )

Figure 5. SPC58XXADPT144S rev. B "mini

module" - bottom - B2

JR12 Device pin 31 port

configuration

1-2

(closed with PCB trace for connect

pin 31 to PI[2] )

Figure 5. SPC58XXADPT144S rev. B "mini

module" - bottom - B2

JR15 Device pin 141 port

configuration

1-2

Figure 5. SPC58XXADPT144S rev. B "mini

module" - bottom - B3

(Closed with PCB trace for connect

pin 141 to PM[2] )

JR16 Device pin 140 port

configuration

1-2

(closed with PCB trace for connect

pin 140 to PM[0] )

Figure 5. SPC58XXADPT144S rev. B "mini

module" - bottom - B3

JR17 Device pin 135 port

configuration

1-2

(closed with PCB trace for connect

pin 135 to PK[14] )

Figure 5. SPC58XXADPT144S rev. B "mini

module" - bottom - B3

JR14

Device pin 98 port

configuration / function

configuration

1-2

(connect pin 98 to ESR0 )

Figure 4. SPC58XXADPT144S rev. B "mini

module" - top - A3

JR18

Device pin 25 port

configuration / function

configuration

1-2

(connect pin 25 to AGND )

Figure 4. SPC58XXADPT144S rev. B "mini

module" - top - C2

UM2827

SPC58xG configuration

UM2827 - Rev 1 page 10/25

Andere Handbücher für SPC58XXADPT144S REV.B

Inhaltsverzeichnis

Andere ST Hauptplatine Handbücher

ST ST9 Series Bedienungsanleitung

ST STEVAL-IHM022V1 Bedienungsanleitung

ST STM32F407 Series Bedienungsanleitung

ST EVALSP320SCPU Bedienungsanleitung

ST SPC58NHADPT176S Bedienungsanleitung

ST L5965 Bedienungsanleitung

ST EVALSPEAr320CPU Bedienungsanleitung

ST STEVAL-IPMnM1S Bedienungsanleitung

ST STEVAL-QUADV01 Bedienungsanleitung

ST STEVAL-USBPD45H Administratorhandbuch

ST B-L4S5I-IOT01A Bedienungsanleitung

ST STEVAL-ISB041V1 Bedienungsanleitung

ST STEVAL-IPC002V1 Bedienungsanleitung

ST SPC582B-DIS Bedienungsanleitung

ST STEVAL-IHM020V1 Bedienungsanleitung

ST STEVAL-STRKT01 Administratorhandbuch

ST STEVAL-IHM010V1 Bedienungsanleitung

ST STM32L073Z-EVAL Bedienungsanleitung

ST STM3221G-EVAL Bedienungsanleitung

ST EVB-LIV4F Bedienungsanleitung

ST STM32L476G-EVAL Bedienungsanleitung

ST SPC560B-DIS Bedienungsanleitung

ST STEVAL-IFS012V1 Bedienungsanleitung

ST STEVAL-ISC004V1 Bedienungsanleitung

Beliebte Hauptplatine Handbücher anderer Marken

DFI

DFI SD170 Bedienungsanleitung

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Bedienungsanleitung