Star Micronics TSP2000 Series Bedienungs- und Wartungshandbuch
THERMAL PRINTER
TSP552
TSP552II
TSP2000
PROGRAMMER'S MANUAL
Trademark acknowledgments
TSP552, TSP552II, TSP2000: Star Micronics Co., Ltd.
ESC/POS: Seiko Epson Corporation
Notice
•Allrightsreserved.Reproductionofanypartofthismanualinanyformwhatsoever,
without STAR’s express permission is forbidden.
•The contents of this manual are subject to change without notice.
•All efforts have been made to ensure the accuracy of the contents of this manual
atthetimeofgoingtopress.However,shouldanyerrorsbedetected,STARwould
greatly appreciate being informed of them.
•The above notwithstanding, STAR can assume no responsibility for any errors in
this manual.
©Copyright 1998-2000 Star Micronics Co., LTD.
TABLE OF CONTENTS
1. Dip Switch Setting (TSP552 / 552II) ..................................................................... 1
1-1. Serial Interface Type..................................................................................... 1
1-2. Parallel Interface Type .................................................................................. 2
2. Dip Switch Setting (TSP2000) ............................................................................... 3
2-1. Serial Interface Type..................................................................................... 3
2-2. Parallel Interface Type .................................................................................. 4
3. Control Codes ......................................................................................................... 5
3-1. Star Mode Command Summary ................................................................... 5
3-2. Star Mode Command Specifications ............................................................ 9
3-3. ESC/POS Mode Command Summary ........................................................ 60
4. Character Code Tables ........................................................................................ 62
Please access the following URL
http://www.star-micronics.co.jp/service/sp_sup_e.htm
for the lastest revision of the manual.
– 1 –
1. Dip Switch Setting (TSP552 / 552II)
1-1. Serial Interface Type
DIP-SW 1
Switch
Function ON OFF
1 Data receive error Error is ignored. “?” is printed.
2 Receive buffer size 45 bytes 4 k bytes
3 Handshaking XON/XOFF DTR/DSR
4 Data bit 7 bits 8 bits
5 Parity check Yes No
6 Parity Even Odd
7Baud rate See Table 1.
8DIP-SW 2
Switch
Function ON OFF
1 Handshaking conditions Receive buffer full Offline or
(conditions for BUSY) receive buffer full
2 <FF> Code (Star mode) Form Feed Cut Command
Graphic Adjustment (ESC/POS mode) 203 DPI 180 DPI
3Print density See Table 2.
4
5 Command STAR ESC/POS
6 Should not be changed (should be set to on).
7 #6 pin reset signal Valid Invalid
8 #25 pin reset signal Valid Invalid
Table 1 Baud Rate
Data Rate SW 1-7 SW 1-8
2400 ON ON
4800 OFF ON
9600 ON OFF
19200 OFF OFF
Table 2 Print Density
Print Density SW 2-3 SW 2-4 Contents of Test Print Page
Light ON ON Level 1
(Standard) OFF ON Level 2
ON OFF Level 3
Dark OFF OFF Level 4
– 2 –
1-2. Parallel Interface Type
DIP-SW 1
Switch
Function ON OFF
1 Auto CR Valid Invalid
2 Receive buffer size 45 bytes 4 k bytes
3
4
5 Do not change. (Should be set to OFF)
6
7
8 Cut position adjust*1 Invalid Valid
(ESC/POS mode only)
*1: Approximately 9mm of paper is fed before cutting.
DIP-SW 2
Switch
Function ON OFF
1 Handshaking conditions Receive buffer full Offline or
(conditions for BUSY) receive buffer full
2 <FF> Code (Star mode only) Form Feed Cut Command
Graphic Adjustment (ESC/POS mode) 203 DPI Adjust for 180 DPI
3Print density See Table 3.
4
5 Command STAR ESC/POS
6 Do not change. (Should be set to ON)
7 ACK plus width 1 µs8µs
8 #31 pin (INIT) reset signal Valid Invalid
Table 3 Print Density
Print Density SW 2-3 SW 2-4 Contents of Test Print Page
Light ON ON Level 1
(Standard) OFF ON Level 2
ON OFF Level 3
Dark OFF OFF Level 4
– 3 –
2. Dip Switch Setting (TSP2000)
2-1. Serial Interface Type
DIP-SW 1
Switch
Function ON OFF
1 Data receive error Error is ignored. “?” is printed.
2 Receive buffer size 68 bytes 4 k bytes
3 Handshaking XON/XOFF DTR/DSR
4 Data bit 7 bits 8 bits
5 Parity check Yes No
6 Parity Even Odd
7 Baud rate 19200 bps 9600 bps
8 Automatic Status Back function Valid Invalid
DIP-SW 2
Switch
Function ON OFF
1 Handshaking conditions Receive buffer full Offline or
(conditions for BUSY) receive buffer full
2 <FF> Code (Star mode) Cut Command Form Feed
Graphic Adjustment (ESC/POS mode) 180 DPI 203 DPI
3Print density See Table 2.
4
5 Should not be changed (should be set to off).
6 Command ESC/POS STAR
7 Pin #25 (INIT) reset signal Valid Invalid
8 Pin #6 (DSR) reset signal INIT DSR
Table 2 Print Density
Print Density SW 2-3 SW 2-4
Power economy mode ON ON
Standard OFF OFF
ON OFF
Dark OFF ON
– 4 –
2-2. Parallel Interface Type
DIP-SW 1
Switch
Function ON OFF
1 Auto CR Valid Invalid
2 Receive buffer size 68 bytes 4 k bytes
3 Should not be changed (should be set to off).
4 Device ID reply Valid Invalid
5 Automatic Status Back function Valid Invalid
6 Negotiation Status Back function Valid Invalid
7Treatment of missing data during reverse Store Delete
8 Cut position adjust *1 Valid Invalid
DIP-SW 2
Switch
Function ON OFF
1 Handshaking conditions Receive buffer full Offline or
(conditions for BUSY) receive buffer full
2 <FF> Code (Star mode) Cut Command Form Feed
Graphic Adjustment (ESC/POS mode) 180 DPI 203 DPI
3Print density See Table 2.
4
5 Should not be changed (should be set to off).
6 Command ESC/POS STAR
7 Always ON Should be set to on.
8
*1 ESC/POS mode only
Table 2 Print Density
Print Density SW 2-3 SW 2-4
Power economy mode ON ON
Standard OFF OFF
ON OFF
Dark OFF ON
– 5 –
3. Control Codes
3-1. Star Mode Command Summary
The details of each command are shown in the following sections.
Commands to Select Characters
Control codes Hexadecimal Function Page
codes
<ESC> "R"
n
1B 52
n
Select international character set 9
<ESC> <GS> t
n
1B 1D 74
n
Select character table 10
<ESC> "/" "1" 1B 2F 31 Select slash zero 10
<ESC> "/" <1> 1B 2F 01
<ESC> "/" "0" 1B 2F 30 Select normal zero 11
<ESC> "/" <0> 1B 2F 00
<ESC> "b"
n1
n2
n3
n4
1B 62
n1 n2 n3 n4
Select bar code printing 11
d1
...
dk
<RS>
d1
...
dk 1E
<ESC> "M" 1B 4D Select 12-dot pitch printing 16
<ESC> "p" 1B 70 Select 14-dot pitch printing 16
<ESC> "P" 1B 50 Select 15-dot pitch printing 16
<ESC> ":" 1B 3A Select 16-dot pitch printing 16
<ESC> <SP>
n
1B 20
n
Set character spacing 17
<SO> 0E Sets the printing magnified double 17
in character width.
<DC4> 14 Resets the printing magnified in 17
character width.
<ESC> "W"
n
1B 57
n
Sets the magnification rate in
18
character width.
<ESC> <SO> 1B 0E Sets the printing magnified 18
double in character height.
<ESC> <DC4> 1B 14 Resets the printing magnified 18
in character height.
<ESC> "h"
n
1B 68
n
Sets the magnification rate 19
in character height
.
<ESC> "–" "1" 1B 2D 31 Select underlining 19
<ESC> "–" <1> 1B 2D 01
– 6 –
Control codes Hexadecimal Function Page
codes
<ESC> "_" "1" 1B 5F 31 Select overlining 20
<ESC> "_" <1> 1B 5F 01
<ESC> "4" 1B 34 Select highlight printing 21
<ESC> "5" 1B 35 Cancel highlight printing 21
<SI> 0F Inverted printing 21
<DC2> 12 Cancel inverted printing 22
<ESC> "E" 1B 45 Select emphasized printing 22
<ESC> "F" 1B 46 Cancel emphasized printing 22
Commands to Set the Page Format
Control codes Hexadecimal Function Page
codes
<ESC> "C"
n
1B 43
n
Set page length in lines 23
<ESC> "C" <0>
n
1B 43 00
n
Set page length in inches 23
<ESC> "N"
n
1B 4E
n
Set bottom margin 24
<ESC> "O" 1B 4F Cancel bottom margin 24
<ESC> "l"
n
1B 6C
n
Set left margin 25
<ESC> "Q"
n
1B 51
n
Set right margin 26
Commands to Move the Print Position
Control codes Hexadecimal Function Page
codes
<LF> 0A Line Feed 27
<ESC> "a"
n
1B 61
n
Feed paper n lines 27
<FF> 0C Form Feed 27
<HT> 09 Horizontal tab 28
<VT> 0B Vertical tab 28
<ESC> "z" "1" 1B 7A 31 Set line spacing to 4 mm 29
<ESC> "0" 1B 30 Set line spacing to 3 mm 29
– 7 –
Control codes Hexadecimal Function Page
codes
<ESC> "J"
n
1B 4A
n
One time n/4 mm feed 29
<ESC> "I"
n
1B 49
n
One time n/8 mm feed 29
<ESC> "B"
n1
n2
... <0> 1B 42
n1 n2
... 00 Set vertical tab stops 30
<ESC> "D"
n1
n2
... <0> 1B 44
n1 n2
... 00 Set horizontal tab stops 30
<ESC> <GS> "A"
n1
n2
1B 1D 41
n1
n2
Absolute position setting 31
<ESC> <GS> "R"
n1 n2
1B 1D 52
n1 n2
Relative position setting 31
<ESC> <GS> "a"
n
1B 1D 61
n
Alignment 32
Commands to Print Dot Graphics
Control codes Hexadecimal Function Page
codes
<ESC> "K"
n
<0> 1B 48
n
00
m1 m2
Print normal density graphics 34
m1 m2
...
<ESC> "L"
n1 n2
1B 4C
n1 n2 m1 m2
Pring high density graphics 36
m1 m2
<ESC> "k"
n
<0>
d1
1B 6B
n
00
d1
Print fine density graphics 38
<ESC> "X"
n1 n2
1B 58
n1 n2
Print fine density graphics 41
<ESC> <FS> "p"
n m
1B 1C
70 n m
Print NV bit image 42
<ESC> <FS> "q" 1B 1C
71
Define NV bit image 43
Commands to Print Download Characters
Control codes Hexadecimal Function Page
codes
<ESC> "&" "1" "1" 1B 26 31 31
n
n
m1 m2
...
m48 m1 m2
...
m48
Define download character 46
<ESC> "&" <1> <1> 1B 26 01 01
n
m1 m2
...
m48 n m1 m2
...
m48
<ESC> "&" "1" "0"
n
1B 26 31 30
n
Delete a download character 48
<ESC> "&" <1> <0>
n
1B 26 01 00
n
<ESC> "%" "1" 1B 25 31 Enable download character set 48
<ESC> "%" <1> 1B 25 01
<ESC> "%" "0" 1B 25 30 Disable download character set 48
<ESC> "%" <0> 1B 25 00
<ESC> <GS> "*" xy 1B 1D 2A 78 79 Definition of download bit image 48
<ESC> <GS> "/"
m
1B 1D 2F 6D Printing of download bit image 50
Andere Handbücher für TSP2000 Series
2
Dieses Handbuch passt für folgende Modelle
2
Inhaltsverzeichnis
Andere Star Micronics Drucker Handbücher
Star Micronics
Star Micronics SP2000 Bedienungsanleitung
Star Micronics
Star Micronics TSP800 Series Bedienungsanleitung
Star Micronics
Star Micronics Line Thermal Printer Bedienungsanleitung
Star Micronics
Star Micronics 10X Bedienungsanleitung
Star Micronics
Star Micronics TUP500 series Bedienungsanleitung
Star Micronics
Star Micronics SP500 Series Bedienungsanleitung
Star Micronics
Star Micronics Rainbow NX-1000C Bedienungsanleitung
Star Micronics
Star Micronics LC-4511 Bedienungsanleitung
Star Micronics
Star Micronics DP8340R Series Bedienungsanleitung
Star Micronics
Star Micronics NL-10 Bedienungsanleitung
Star Micronics
Star Micronics LC-15 Bedienungsanleitung
Star Micronics
Star Micronics TSP400 Series Bedienungsanleitung
Star Micronics
Star Micronics SP2000 Bedienungs- und Wartungshandbuch
Star Micronics
Star Micronics TUP900 Series Bedienungsanleitung
Star Micronics
Star Micronics SB-10 Bedienungsanleitung
Star Micronics
Star Micronics SP312F Bedienungsanleitung
Star Micronics
Star Micronics NP-IO Bedienungsanleitung
Star Micronics
Star Micronics LC-1011C Bedienungsanleitung
Star Micronics
Star Micronics SP500 Series Montageanleitung
Star Micronics
Star Micronics FVP-10U Bedienungsanleitung
