Star Trac Spinner NXT 7090 Einrichtungshandbuch

620-8006 Rev A

STAR TRAC

14410 Myford Road

Irvine, CA 926060 USA

COVER PAGE FOR DOCUMENT CONTROL PURPOSES ONLY, NOT TO BE PRINTED

Document:

Document Title: MANUAL, SP INSTALLATION, NXT

Document Number:620-8006 Rev: 001

Page Number: 1 of 16

Material:

n/a

Notes:

n/a

Approvals:

Originator

Print:

Deo Magakat

Sign: Date: 04/12/11

Approved By:

Sign: Date:

Document Revision History:

REV EFFECTIVE DATE BY DESCRIPTION ECO NO.

01 DMM DRAFT

A 14 June 2011 DMM RELEASE 13510

THE INFORMATION CONTAINED HEREIN IS PROPRIETARY AND CONFIDENTIAL TO UNISEN INC/STAR TRAC.

AND SHALL NOT BE USED OR DISCLOSED, IN WHOLE OR IN PART, WITHOUT FIRST OBTAINING THE WRIT-

TEN PERMISSION OF UNISEN, INC.

Print:

620-8006 Rev A

STAR TRAC

14410 Myford Road

Irvine, CA 926060 USA

SPINNER ASSEMBLY AND

INSTALLATION MANUAL

620-8006 Rev A

GENERAL

Before using this product, it is essential to read ALL installation Instructions and this

ENTIRE operations manual; the manual describes equipment setup and instructs

members on how to use it correctly and safely.

1. Open-End Wrench (Included)

2. Multi-purpose Wrench (Included)

3. 14mm Socket Wrench (Not Included)

4. 18mm Socket Wrench (Not Included)

5. 18mmHex Wrench (Not Included)

6. 21mm Open-end Wrench (Not Included)

7. Torque Wrench (Not Included)

8. Loctite 242 (Not Included)

9. Loctite 262 (Not Included)

TOOLS REQUIRED

If you are a Factory Certified Installer you must:

•

Adhere to all torque and assembly specifications.

•

Use a CALIBRATED TORQUE WRENCH with the necessary hex key sockets

•

NOT USE a powered drill, powered driver or powered impact tool for any part of the assembly.

•

Complete the assembly checklist on each Star Trac product.

•

Complete the final programming, functional and cosmetic checklists for each Star Trac product.

FACTORY CERTIFIED INSTALLER

Spin

, Spinner

, Spinning

and the Spinning logo are registered trademarks of Mad Dogg Athletics, Inc.

Smart Release™ is a registered trademark of Nautilus, Inc.

SPD is a registered trademark of Shimano American Corporation.

Every effort has been made to keep this information current; however, periodically, changes are made to the information herein, and these changes

will be incorporated into new editions of this publication. All product names and logos are trademarks of their respective owners.

620-8006 Rev A

Step 3.

Fold back all flaps at the top and at the bottom of

the box.

Step 4.

Slide-up the outer carton.

Step 2.

Open the carton first at the top and bottom. Use

scissors or a knife to cut the tape.

Caution: Be careful not to injure yourself; always

cut away from your body.

Step 1.

Arrange the assembly area so that the area is free

from objects that could potentially damage the

parts.

When positioning the box erify that the

HEAVY END logo is at the bottom as indicated by

the black o al in the picture.

UNPACKING INSTRUCTIONS

620-8006 Rev A

Step 8.

Position the main frame assembly upright and

remo e plastic protector.

Step 6.

Remo e the foam inserts from the shipment by

first taking out foam insert (1), then foam inserts

(2), and then last foam insert (3).

Step 5.

Arrange the unpacking area so that the area is

free from objects that could potentially damage

unpacked components.

Step 7.

Remo e components from foam inserts.

2 3

620-8006 Rev A

Step 9.

Place the main frame assembly on a flat surface

that is free from objects that could potentially

damage the unit.

Step 12.

Verify that the Spare Kit contains:

1. Pedal straps (2)

2. Spare brake pad (1)

Note: If the shipment is incomplete please con-

tact the Service Department at (800) 503-1221.

Step 10.

Verify that all shipment components are included:

1. Hardware, Pop-pin, and Pedals (set of two)

2. Handlebar w Grip and Water Bottle Holders (1)

3. Handlebar Post (1)

4. Seat Post (1)

5. Rear Leg Assembly (1)

6. Seat Slider Assembly w/Saddle (1)

Front Leg Assembly w/Transport Wheels (1)

4 5

6 7

2 1

3 4

Step 11.

Verify the Hardware Kit contents:

1. M10 Flat Washer (4)

2. M10 Split Lock Washer (4)

3. M10X1.5, 25mm Hex Head Screw (4)

4. M8X1.25, 12mm Flange Hex Head Screw (2)

5. Open-End Wrench (1)

6. Multi-purpose Wrench (1)

7. Hex Wrenches (3)

620-8006 Rev A

Step 14.

Locate (2) M10 Hex Head screw. Pre-install an M10

Split Lock Washer and an M10 Flat Washer onto each

Hex head screw.

Note: Pay attention to the order of assembly of the

Split Loc Washer and Flat Washer.

Step 13.

Place the rear leg assembly in the mating position

under the frame.

Note: Ma e sure the thread posts in the frame

and the holes in the rear leg assembly are in

alignment.

ASSEMBLY INSTRUCTIONS

Step 15.

Secure the rear feet to the frame using (2) M10

Hex Head Screws with (2) M10 Split Lock Wash-

ers, and (2) M10 Flat Washer.

Torque screws to 35-40 lb-ft (47-54 Nm).

Note: Start threading screws by hand, then

tighten using an 18mm open-end or soc et

wrench.

Step 16.

Secure the front feet to the frame using (2) M10 Hex

Head Screws with (2) M10 Split Lock Washers, and

(2) M10 Flat Washer.

Torque screws to 35-40 lb-ft (47-54 Nm). Verify

that the front and rear feet are parallel to each

other.

Note: Start threading screws by hand, then tighten

using an 18mm open-end or soc et end wrench.

620-8006 Rev A

Step 20.

Locate the Pop-pin shown abo e.

Step 17.

Slide the Handlebar w/ Grip and Water Bottle

Holder onto the Handlebar Post.

Note: You may have to pull up on the Loc Knob

to help align the Slider Clamp with the guide rail.

Step 18.

Using a 2.5mm Hex Key, tighten the Button Head

Screw all the way down. This screw limits the

tra el of the Handlebar and pre ents the Handle-

bar from sliding off the Handlebar post acciden-

tally.

Note: Verify that no gap exists between the head

of the screw and the Handlebar slide rail.

Step 19.

Loosen the Pop-pin and pull it out away from the

Frame Handlebar Post.

Install and slide the Handlebar assembly into the

Frame Handlebar Post.

620-8006 Rev A

Step 23.

Align the slider clamp with the guide rail by turning

the Seat Slider Lock Knob.

Pull down on the locking pin and slide the seat rail

onto the seat post assembly.

Step 22.

With the Pop-pin loose pull and hold it away from

the frame seat post.

Install Seat Post into the Frame Seat Post.

Step 24.

Release the locking pin when the arrow points to a

alue between 0 and 7.

Step 21.

Install the Pop-pin into the Frame Seat Post using

a 21mm Open-end Wrench.

620-8006 Rev A

Step 25.

Locate the set of left and right pedals and follow

the orientation as shown in the picture abo e dur-

ing installation.

Step 28.

Secure the pedal tightly by using a 14mm Socket

wrench. Do not use an open end wrench to

tighten the pedal screws.

Torque screw to between 35-40 lbs-ft (47-54

Nm). Co er screw with Plastic End Cap.

Note: To prevent the pedal/cran arm from rotat-

ing, loc down the flywheel by turning the Bra e

Resistance nob cloc wise all the way down.

Step 26.

Locate one (1) M8x1.25 Flanged Hex Head

Screw, and (1) Plastic End Cap.

Note: Chec to ma e sure the screw has a blue

or red Loctite patch on the threads.

L R

Step 27.

Using a rubber mallet, firmly tap the left pedal

shaft into the left crank arm to seat and engage

the tapered shaft securely.

Start threading in the M8X1.25 Flanged Hex

Head screw by hand into the end of the pedal

shaft.

Note: Chec Cran Arm tapered hole and verify

that it is free of burrs or other debris. Verify that

the pedal tapered shaft is burr-free and clean.

Inhaltsverzeichnis

Andere Star Trac Heimtrainer Handbücher

Star Trac

Star Trac Upright Pro bike Bedienungsanleitung

Star Trac

Star Trac E-UB Bedienungsanleitung

Star Trac

Star Trac Spinner v Bedienungsanleitung

Star Trac

Star Trac V-Bike Bedienungsanleitung

Star Trac

Star Trac 7270 Bedienungsanleitung

Star Trac

Star Trac Spinner Bike NXT 7000 Bedienungsanleitung

Star Trac

Star Trac Pro Upright Bike Bedienungsanleitung

Star Trac

Star Trac 4-UB Bedienungsanleitung

Star Trac

Star Trac SPINNER PRO+ Bedienungsanleitung

Star Trac

Star Trac Spinner ELITE 6900 Handbuch

Star Trac

Star Trac Star Trac Fitness S-UBx Bedienungsanleitung

Star Trac

Star Trac SPINNER BLADE ION Betriebsanleitung

Star Trac

Star Trac Pro Upright Bike Bedienungsanleitung

Star Trac

Star Trac 4-UB Bedienungsanleitung

Star Trac

Star Trac 4-RB Bedienungsanleitung

Star Trac

Star Trac S-UBx Bedienungsanleitung

Star Trac

Star Trac Turbo Trainer Bedienungsanleitung

Star Trac

Star Trac Pro Bike 6000 Series Bedienungsanleitung

Star Trac

Star Trac eSPINNER Bedienungsanleitung

Star Trac

Star Trac Spinner Bike NXT 7000 Bedienungsanleitung

Star Trac

Star Trac Spiner V Bedienungsanleitung

Star Trac

Star Trac Spinner NXT Black Belt Handbuch

Star Trac

Star Trac Spinner, Spinner Pro, Spinner Einrichtungshandbuch

Star Trac

Star Trac Upright Sport Bike Bedienungsanleitung

Beliebte Heimtrainer Handbücher anderer Marken

Weslo

Weslo Vector 302 Kurzanleitung

TOORX

TOORX BRX85 Bedienungsanleitung

Matrix

Matrix KranKcycle Bedienungsanleitung

Matrix

Matrix IC3 Bedienungsanleitung

Sunny Health & Fitness

Sunny Health & Fitness SF-B121021 Bedienungsanleitung

Monark

Monark 827E Bedienungsanleitung

Stamina

Stamina 1310 Bedienungsanleitung

American Fitness

American Fitness SPR-BK1072A Bedienungsanleitung

Cateye

Cateye CS-1000 (CYCLO SIMULATOR) Bedienungsanleitung

BH FITNESS

BH FITNESS H9158H Bedienerhandbuch

Body Sculpture

Body Sculpture BC-7220G Bedienungsanleitung

Cateye

Cateye EC-2300 Bedienungsanleitung

FYTTER

FYTTER RACER RC MSR Bedienungsanleitung

Kikos

Kikos HM-9090M Bedienungsanleitung

Pro-Form

Pro-Form 345 Zlx Bike Benutzerhandbuch

Fuel Fitness

Fuel Fitness SU135-40 Bedienungsanleitung

NordicTrack

NordicTrack Gxr 4.2 Bike Bedienungsanleitung

Vision Fitness

Vision Fitness U70 Bedienungsanleitung