Starrett FORM 966 Bedienungsanleitung

Trust Is In The Name User Manual

FORM 966

2 FORM 966

READ THIS MANUAL BEFORE USING THE INSTRUMENT

ANTES DE UTILIZAR EL INSTRUMENTO,

LEA ATENTAMENTE ESTE MANUAL

LIRE CE MANUEL AVANT D'UTILISER L'INSTRUMENT

LEIA ATENTAMENTE ESTE MANUAL ANTES

DE UTILIZAR O INSTRUMENTO

使用仪器前请阅读本操作手册

DIESES HANDBUCH VOR DER VERWENDUNG

DES MESSGERÄTS LESEN

LEGGERE ATTENTAMENTE QUESTO MANUALE PRIMA

DI UTILIZZARE QUESTO STRUMENTO

01/18 Q

2900 ELECTRONIC INDICATOR

USER MANUAL

4 FORM 966

TABLE OF CONTENTS

Guidelines for Indicator Care 6

Operating Instructions 6

Indicator Components, Dimensions and Layout 7

Button Functions 8

2900 Indicator Models, Feature Level and Resolution 9

Resolution Selection* 9

Setting the Preset Function 10

Setting MIN/MAX Limits (Go/No Go) 10

Displaying MIN/MAX/TIR Values** 12

Lock Mode* 12

Data Output Connection 13

Battery Installation 13

Appendix A: Technical Speciﬁcations 14

Appendix B: Serial Output Connector 14

*Available with Standard and Advanced Features

**Available only with Advanced Features

FORM 966 5

2900 ELECTRONIC INDICATOR

THIS IS A STARRETT USER GUIDE FOR THE

2900 ELECTRONIC INDICATOR.

ALL SPECIFICATIONS IN THIS DOCUMENT ARE CORRECT

AT TIME OF PRODUCTION AND ARE SUBJECT TO CHANGE.

PLEASE CONTACT STARRETT FOR FURTHER INFORMATION.

6 FORM 966

ENGLISH

GUIDELINES FOR INDICATOR CARE

1. Avoid dropping the indicator.

2. Avoid extreme temperatures and direct sunlight for extended periods.

3. Avoid contact with liquids and dusty environments.

4. Avoid shocks to the contact point and spindle.

5. Do not apply radial force to the spindle.

6. If the indicator is stem-mounted, protect it from being hit or bumped to

avoid stem/case mechanical alignment damage.

7. Do not over-tighten the mounting mechanism. If possible, use clamp

mounting rather than set screws to prevent damage to the spindle.

8. Clean the spindle frequently with a dry cloth or a chamois to prevent

sluggish or sticky movement. Isopropyl alcohol may be used to remove

gummy deposits on metallic parts. Do not apply lubricant to the spindle

or use solvents.

9. Do not disassemble or modify the indicator.

OPERATING INSTRUCTIONS

1. Install batteries (included with indicator).

2. Lightly clean the contact point.

3. Secure the indicator to an appropriate holding device.

4. Press the ON/OFF button to turn the indicator on.

5. Select the unit of measure (inch or millimeter) by pressing the IN/mm

button. (Not applicable to metric indicator models).

6. Place the indicator perpendicular to the reference surface being measured.

Allow enough movement to be able to take a higher or lower measurement.

7. Press the ZERO button to reset the display.

8. Lift the spindle, remove the reference surface and place the work piece

to be measured. Put the spindle carefully on to its surface. The measured

value will be shown on the LCD.

9. Press and hold the ON/OFF button to turn the indicator off. If left

unattended, it will turn off automatically in 30 minutes.

FORM 966 7

ENGLISH

Stem Cap

Data Cable

Spindle

Bellows

Spindle

Contact Point

Stem

Data Output Cover

Battery Drawer

Back Lug

1-21/32"

(42.2mm)

1/4"

(6.5mm)

1/4" (6.5mm)

2-5/64" (53mm)

3/8"

(9.5mm)

INDICATOR COMPONENTS, DIMENSIONS AND LAYOUT

8 FORM 966

ENGLISH

6 & 12

4 & 8

1 & 11

3, 9 & 10

2 & 7

BUTTON FUNCTIONS

LOCK, RES, LIMITS and PRESET,

printed in yellow, are used in

conjunction with the SHIFT button.

To engage press the SHIFT button

ﬁrst. The SET icon will appear on

the bottom left corner. Then press

the button for the desired function.

1 ON/OFF Power button. Press and hold for 4 seconds.

2 ± Plus/Minus sets the direction of the reading

3 ZERO Half a second after releasing the ZERO button the display will

zero. Do not move from zero during that half second.

4 IN/mm Toggles the display between English or Metric modes.

5 SHIFT/SET

Dual function. To enable the Lock, Resolution Selection, Preset or

Limits (Go/No Go) function. When enabled, SET icon will show in

the bottom left corner of the display.

6 LOCK

Prevents operator modiﬁcation to the Settings. Press SHIFT/SET

button, then press and hold the LOCK button (after setting the

other functions).

7 RES

Resolution. First select the Unit (English/Metric). Press SHIFT/SET

then the RES (Plus/Minus) buttons. Press the RES button to scroll

through choices and press the SHIFT/SET to make the selection.

8 LIMITS Sets the Min and Max values for the Go/No Go function.

9 PRESET Press the SHIFT/SET button then press the PRESET button to

enable the PRESET function.

10 ZERO/ABS Dual Function. Press and hold for two seconds to activate the ABS

mode or to exit the ABS mode. To zero the display, see #3 above.

11 HOLD Press HOLD momentarily to capture a reading.The captured reading

will ﬂash on and off. To disable, press the HOLD button again.

12 MIN/MAX/TIR

Displays the minimum or maximum values captured during

operation. The TIR function displays the difference between the

captured readings.

FORM 966 9

ENGLISH

RESOLUTION SELECTION*

Enter the resolution SET mode by pressing the

SHIFT/SET button followed by the RES button. The

choices are displayed sequentially from highest to

lowest. The round off accommodates the range of

values in the table (right).

After selecting the desired resolution, press the SET/SHIFT button to exit the resolution

mode. When the mode is entered, the resolution selection is presented in the units

previously set (English or metric). Press IN/mm to toggle units selection, as required.

2900 INDICATOR MODELS, FEATURE LEVEL, RESOLUTION AND RANGE

CAT. NO. EDP DESCRIPTION RESOLUTION RANGE

2900-1 09980 Basic English/Metric .00005"/.001mm .5"/12mm

2900-2 09981 Basic English/Metric .0001"/.001mm .5"/12mm

2900-4 09983 Standard English/Metric

with Selectable Resolution

.0005"/.0001"/.00005"

.01mm /.001mm .5"/12mm

2900-6 09985 Advanced English/Metric

with Selectable Resolution

.0005"/.0001"/.00005"

.01mm /.001mm .5"/12mm

2900-1M 09986 Basic Metric .001mm 12mm

2900-4M 09988 Standard Metric with

Selectable Resolution .01mm /.001mm 12mm

2900-6M 09990 Advanced Metric with

Selectable Resolution .01mm /.001mm 12mm

Press

SHIFT / SET

BUTTON Then

RES

Button to enter Resolution Mode

Press

RES

Button

to cycle through the available resolutions

Press

SHIFT / SET

BUTTON to pick the resolution and exit resolution mode

*Available with Standard and Advanced Features

ROUND OFF CONDITION ENGLISH INCH MODE METRIC MM MODE

Round Off Enabled 000.00005 0000.001

Round Off Disabled 000.0001 0000.001

Round Off Enabled 000.0005 0000.01

Round Off Disabled 000.001 0000.01

10 FORM 966

ENGLISH

SETTING THE PRESET FUNCTION*

1. To set a value, press and hold the ZERO/

ABS button until the ABS icon appears in

the upper right corner of the LCD (right).

The values can be SET to: ±99.99999"

or ±9999.999mm.

2. Press the SHIFT/SET followed by the

PRESET button. The SET and PRESET

icons will appear in the lower left corner

of the LCD. The PRESET icon will be

ﬂashing (middle right).

3. To move from the PRESET icon to a digit,

press the SHIFT/SET button. A ﬂashing

digit indicates that it is ready to be SET

(lower right). Press the PRESET button to

increment the value. To set, press the SHIFT/SET button.

4. To move to the next digit press the SHIFT/SET button and repeat step 3.

Repeat steps 2 and 3 until all the digits are SET.

5. To set a negative value, press PRESET when the plus/minus sign icon is ﬂashing.

6. To exit the PRESET function, press the PRESET button when the PRESET

icon is ﬂashing. The SET value will remain displayed.

7. Press and hold the ZERO/ABS button to return to the active measuring mode.

SETTINGMIN/MAX LIMITS(GO/NO GO FUNCTION)**

1. Select the units to be displayed.

2. Press the SHIFT/SET button. The SET icon will

appear in the lower left corner (right).

3. Press the LIMITS button. The MIN LIMIT icon

will appear in the upper middle of the display.

Press

SHIFT / SET

BUTTON Then

PRESET

Button

to enter Preset Mode

Press

SHIFT / SET

BUTTON to cycle from digit to digit and back to preset

Press

PRESET

Button

to increment the value of the digit or the plus/minus sign

*Available with Standard and Advanced Features

Inhaltsverzeichnis

Andere Starrett Messgerät Handbücher

Starrett

Starrett Electronic IP67 Bedienungsanleitung

Starrett

Starrett 64381 Bedienungsanleitung

Starrett

Starrett W733.1 Bedienungsanleitung

Starrett

Starrett LMXP-100 Bedienungsanleitung

Starrett

Starrett AV300 Bedienungsanleitung

Starrett

Starrett 749.1 Bedienungsanleitung

Starrett

Starrett 749.1 Bedienungsanleitung

Starrett

Starrett EC799 Bedienungsanleitung

Starrett

Starrett 2900 Series Bedienungsanleitung

Starrett

Starrett SR100 Bedienungsanleitung

Starrett

Starrett 3752 Series Bedienungsanleitung

Starrett

Starrett 2900 Series Bedienungsanleitung

Starrett

Starrett 2900 Series Bedienungsanleitung

Starrett

Starrett W798 Bedienungsanleitung

Starrett

Starrett 5000B Series Bedienungsanleitung

Starrett

Starrett IQ Bedienungsanleitung

Starrett

Starrett 798 Series Bedienungsanleitung

Starrett

Starrett 436.1 Bedienungsanleitung

Starrett

Starrett 3900 Series Bedienungsanleitung

Starrett

Starrett 799A Series Bedienungsanleitung

Starrett

Starrett 799A Series Bedienungsanleitung

Starrett

Starrett UM3202 Bedienungsanleitung

Starrett

Starrett PKG08806-UMDFG Bedienungsanleitung

Starrett

Starrett 2900-1 Series Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung