StarTech.com SAT3510BU3 Bedienungsanleitung
SATA Hard Drive Enclosure
3.5” SuperSpeed USB 3.0 to
SATA Hard Drive Enclosure
with Fan
SAT3510BU3
Instruction Manual
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.•
Increase the separation between the equipment and receiver.•
Connect the equipment into an outlet on a circuit different from that to which the receiver•
is connected.
Consult the dealer or an experienced radio/TV technician for help.•
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other
protected names and/or symbols of third-party companies not related in any way to
StarTech.com. Where they occur these references are for illustrative purposes only
and do not represent an endorsement of a product or service by StarTech.com, or an
endorsement of the product(s) to which this manual applies by the third-party company
in question. Regardless of any direct acknowledgement elsewhere in the body of
this document, StarTech.com hereby acknowledges that all trademarks, registered
trademarks, service marks, and other protected names and/or symbols contained in this
manual and related documents are the property of their respective holders.
i
Table of Contents
Introduction..................................................................... 1
Packaging Contents.....................................................................1
System Requirements .................................................................1
Rear View ....................................................................................2
Side View.....................................................................................2
Installation....................................................................... 3
Hardware Installation...................................................................3
Driver Installation.........................................................................3
Verifying Installation.....................................................................4
Using the Enclosure ....................................................... 4
Specifications.................................................................. 6
Technical Support........................................................... 7
Warranty Information...................................................... 7
1
Introduction
Th StarTech.com SAT3510BU3 USB 3.0 External Hard Drive
Enclosure lets you connect a 3.5” SATA hard drive through USB 3.0.
A cutting edge external storage solution that lets you harness the
speed and performance supported by the SuperSpeed USB interface.
Supporting data transfer rates of up to 5 Gbps, 10x that of USB 2.0,
and 60% faster than SATA 3Gbps eSATA, plus backward compatible
with USB revisions 2.0 (480Mbps) and 1.1 (12Mbps), so the enclosure
can be used with older systems that don’t support USB 3.0 yet.
Packaging Contents
1 x SAT3510BU3 enclosure•
1 x USB 3.0 A-B cable•
1 x Universal Power Adapter•
3 x Power Adapter plugs (NA, UK, EU)•
1 x Foam pad•
1 x Instruction Manual•
System Requirements
Internal 3.5” SATA compatible storage•
drive
USB enabled computer system with•
available port
Microsoft• ®Windows®2000/XP/Server
2003/Vista/Server 2008 R2/7 (32/64-
bit) or Apple®Mac OS®X or Linux®
2
Power switch
USB 3.0
type B Power
connector
Fan switch
Power/Activity
LED
Cooling Fan
Rear View
Side View
3
Installation
WARNING: Hard drives require careful handling, especially when
being transported. If you are not careful with your hard disk, lost data
may result. Always handle your hard drive and storage device with
caution.
Hardware Installation
Set the enclosure on a flat surface, with the cooling fan facing1.
downwards.
On the top panel, remove the two small screws at the corners.2.
Remove the top panel.
Located at the opposite end from the internal SATA connectors is a3.
small plastic wedge. Flip the wedge up and out of the enclosure.
Place the 3.5” SATA hard drive into the enclosure and then slide it4.
into the SATA connectors.
Flip the wedge down again, to secure the hard drive. For thinner5.
hard drives, an optional, thicker foam pad is included.
Place the top panel back on to the enclosure and fasten the two6.
corner screws.
Connect the external power adapter to the enclosure and flip the7.
power switch to the “1” position. The enclosure and hard drive will
power up.
Connect the USB cable from the enclosure to the computer system.8.
Driver Installation
No driver installation is required for USB enabled operating systems,
as this enclosure uses natively installed drivers. Supported operating
systems should automatically detect and install the enclosure.
4
Verifying Installation
Windows 2000/XP/Server 2003/Vista/7
From the main desktop, right-click on “My Computer” (“Computer”
in Vista/7), then select Manage. In the new Computer Management
window, select Device Manager from the left window panel.
Double-click on the “Disk Drives” option. A new disk drive should be
listed under this category. It will typically contain the make/model of
the hard drive you have installed in the enclosure.
Using the Enclosure
Windows 2000/XP/Vista/7
If you are using a brand new hard drive that does not contain any data,
then you will first need to prepare the hard drive for use. From the
main desktop, right-click on “My Computer” (“Computer” in Vista/7),
then select Manage. In the new Computer Management window, select
Disk Management from the left window panel.
5
Locate the Disk that says it is “Unallocated” (check hard drive capacity
to confirm it’s the correct hard drive) and then right-click in the section
that says “Unallocated” and select “New Partition”.
The New Partition Wizard will appear. Follow the instructions in the
wizard to complete setting up the drive. Once complete, the Disk
should show up as “Healthy” with a drive letter assigned (ie. E:). This
drive letter should now appear within My Computer.
If you are installing a hard drive that already has data on it, then after
plugging it in, the drive should automatically show up with a drive letter
assigned within My Computer.
6
Specications
Bus Interface USB 3.0
Chipset ID ASMedia ASM1051
Connectors 1 x USB 3.0 type B
1 x DC Power
Fans 1 x 80mm
LEDs 1 x Power/Activity
Maximum Data Transfer Rate USB 3.0: 5Gbps
Compatible Hard Drives 3.5” SATA drive (internal)
up to 2TB capacity
Power Adapter 12VDC, 2A, center positive
Operating Temperature 0°C ~ 60°C (32°F ~ 140°F)
Storage Temperature 0°C ~ 70°C (-4°F ~ 158°F)
Humidity 10 ~ 90% RH
Dimensions 143.0mm x 52.1mm x 180.0mm
Weight 580g
Compatible Operating
Systems
Windows 2000/XP/Server 2003/
Vista/Server 2008 R2/7 (32/64),
Mac OS X, Linux
7
Technical Support
StarTech.com’s lifetime technical support is an integral part of our
commitment to provide industry-leading solutions. If you ever need
help with your product, visit www.startech.com/support and access
our comprehensive selection of online tools, documentation, and
downloads.
Warranty Information
This product is backed by a one year warranty.
In addition, StarTech.com warrants its products against defects in
materials and workmanship for the periods noted, following the initial
date of purchase. During this period, the products may be returned
for repair, or replacement with equivalent products at our discretion.
The warranty covers parts and labor costs only. StarTech.com does
not warrant its products from defects or damages arising from misuse,
abuse, alteration, or normal wear and tear.
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA
LLP (or their officers, directors, employees or agents) for any damages
(whether direct or indirect, special, punitive, incidental, consequential, or
otherwise), loss of profits, loss of business, or any pecuniary loss, arising
out of or related to the use of the product exceed the actual price paid
for the product. Some states do not allow the exclusion or limitation of
incidental or consequential damages. If such laws apply, the limitations
or exclusions contained in this statement may not apply to you.
Andere Handbücher für SAT3510BU3
1
Inhaltsverzeichnis
Andere StarTech.com Gehäuse Handbücher
StarTech.com
StarTech.com UNI3510U2 Bedienungsanleitung
StarTech.com
StarTech.com S252BU313R Bedienungsanleitung
StarTech.com
StarTech.com SMS2BU31C3R Bedienungsanleitung
StarTech.com
StarTech.com SAT3510BU3 Bedienungsanleitung
StarTech.com
StarTech.com RK920WALM Bedienungsanleitung
StarTech.com
StarTech.com S252SMTB3 Bedienungsanleitung
StarTech.com
StarTech.com IDECASE35F Handbuch
StarTech.com
StarTech.com InfoSafe S252U2ERR Bedienungsanleitung
StarTech.com
StarTech.com RK12WALHM Bedienungsanleitung
StarTech.com
StarTech.com S251BU31REM Bedienungsanleitung
StarTech.com
StarTech.com HSB2535SATBK Bedienungsanleitung
StarTech.com
StarTech.com S2510U2WF Bedienungsanleitung
StarTech.com
StarTech.com SAT2510U2E Bedienungsanleitung
StarTech.com
StarTech.com RK1820WALHM Bedienungsanleitung
StarTech.com
StarTech.com InfoSafe UNI3510U2E Bedienungsanleitung
StarTech.com
StarTech.com IDECASE525U2 Bedienungsanleitung
StarTech.com
StarTech.com SAT3540ER2 Bedienungsanleitung
StarTech.com
StarTech.com SAT2510U2F Bedienungsanleitung
StarTech.com
StarTech.com S3510BMU33ET Systemhandbuch
StarTech.com
StarTech.com SAT3510U2F Bedienungsanleitung
