StarTech.com ST122UTPAL Bedienungsanleitung

Manual Revision: 07/12/2011

DE: Bedienungsanleitung - de.startech.com

FR: Guide de l'utilisateur - fr.startech.com

ES: Guía del usuario - es.startech.com

IT: Guida per l'uso - it.startech.com

NL: Gebruiksaanwijzing - nl.startech.com

PT: Guia do usuário - pt.startech.com

For the most up-to-date information, please visit: www.startech.com

ST122UTPAL

VGA Video Extender over Cat 5 with

Audio and RGB SKEW Calibration

FCC Compliance Statement

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment

o and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit dierent from that to which the receiver is

connected.

Consult the dealer or an experienced radio/TV technician for help.

Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols

This manual may make reference to trademarks, registered trademarks, and other protected

names and/or symbols of third-party companies not related in any way to StarTech.com.

Where they occur these references are for illustrative purposes only and do not represent an

endorsement of a product or service by StarTech.com, or an endorsement of the product(s) to

which this manual applies by the third-party company in question. Regardless of any direct

acknowledgement elsewhere in the body of this document, StarTech.com hereby acknowledges

that all trademarks, registered trademarks, service marks, and other protected names and/or

symbols contained in this manual and related documents are the property of their respective

holders.

Instruction Manual i

Table of Contents

Introduction........................................................................................................................................................1

Packaging Contents ................................................................................................................................1

System Requirements ............................................................................................................................1

Side View 1....................................................................................................................................................2

Side View 2....................................................................................................................................................2

Installation............................................................................................................................................................3

Preparing Your Site...................................................................................................................................3

Installing the Local Unit ........................................................................................................................4

Installing the Remote Unit..................................................................................................................4

Driver Installation......................................................................................................................................5

How to Use..........................................................................................................................................................5

Mode A Conguration...........................................................................................................................6

Mode B Conguration ...........................................................................................................................6

EDID Copy......................................................................................................................................................6

Specications.....................................................................................................................................................8

Technical Support...........................................................................................................................................9

Warranty Information....................................................................................................................................9

Instruction Manual 1

Introduction

This VGA and audio over Cat5 video extender allows you to extend a VGA signal using Cat5

/ Cat5e cabling to 4 (2 local and 2 remote) monitors to be connected to a single PC. This

transmitter and receiver pair is unique because it oers a rotary control wheel that allows you

toggle on/o the display signal to connected display devies on the receiver and adjust audio

output volume. Plus, the rotary control wheel can be used to help you ne tune the video signal

by oering RGB (red, green, blue) skew calibration, gain, and equalizer controls.

Packaging Contents

• 1 x ST122UTPAL local unit

• 1 x ST122UTPAL remote unit

• 2 x Power Adapter

• 2 x Grounding Wire

• 1 x Instruction Manual

System Requirements

• VGA enabled display device

• VGA enabled video source

• Stereo audio source with 3.5mm mini-jack plug (optional)

• Stereo speakers with 3.5mm mini-jack plug (optional)

• Available electrical power outlet at local and remote locations

Instruction Manual 2

VGA/Audio

output 2

VGA/Audio

output 1

Power

connector

RJ45

connector

VGA/Audio

Input

VGA/Audio

output 1

VGA/Audio

output 2

EDID Copy button

Remote

Unit

Side View 1

Local Unit

Side View 2

Remote

Unit

Local Unit

Instruction Manual 3

Installation

NOTE: To prevent potential electrical damage to the units in some environments, ensure that

the chassis is properly grounded. Place cables away from uorescent lights, air conditioners, and

machines that are likely to generate electrical noise.

This product is composed of two dierent units: the Local Unit and the Remote Unit. The Local

Unit takes the output from an analog audio and VGA video signal source (usually a computer)

and transmits it to the Remote Unit over UTP Ethernet cable. The remote display(s) (monitor,

projector, etc) and speaker(s) connect to the Remote Unit using standard VGA and 3.5mm mini-

jack connections respectively and displays the image and audio from the local computer onto

the remote display(s) and speaker(s).

Preparing Your Site

1. Determine where the local computer will be located and set up the computer.

2. Determine where the remote display(s) will be located and place/mount them appropriately.

3. If you are using surface cabling, ensure you have enough unshielded twisted pair (UTP)

Ethernet cabling to connect the Local Unit to the Remote Unit’s location, and that each end is

terminated with a RJ45 connector. Make sure the cabling does not go through any standard

networking equipment (i.e. routers, modems, switches, etc).

If you are using premise cabling, ensure that the unshielded twisted pair (UTP) Ethernet

Cabling between the Local Unit and the Remote Unit has been properly terminated in a wall

outlet in each location and there is a patch cable long enough to connect the Remote Unit

and the Local Unit to their respective outlets. Make sure the cabling does not go through any

standard networking equipment (i.e. routers, modems, switches, etc).

Instruction Manual 4

Installing the Local Unit

1. Make sure to power o any display devices and the video source device before attempting

the installation.

2. Place the Local Unit near the local video/audio source device.

3. Use a male/female DE-15 VGA cable (not included) to connect the VGA source device (i.e.

computer system) to the input on the ST122UTPAL transmitter unit. If using audio, connect a

3.5mm mini-jack cable from the audio input connector the audio source (i.e. sound card).

4. If using a local monitor, connect a VGA monitor to one of the output connectors on the

transmitter unit. If using audio, connect a set of speakers/headphones with a 3.5mm mini-

jack connector to the audio output connector. Both sets of outputs on the Local unit are

identical.

5. Connect the UTP Ethernet cable to the RJ45 connector on the Local unit.

6. Connect the power adapter from an available power outlet to the Local unit.

Installing the Remote Unit

1. Connect the Remote Unit to the UTP cable connected from the Local Unit.

2. Connect a VGA cable from the remote display to one of the VGA output connectors on the

remote unit. If using audio, connect speakers to the 3.5mm mini-jack port from the same set

of outputs.

OPTIONAL: A second set of display and speakers can be connected to the Remote Unit via

the second set of outputs. Both outputs are identical.

3. Connect the Power Adapter (provided) into an appropriate power source and plug the

opposite end into the power connector on the Remote Unit.

CAUTION: The UTP Ethernet cables that connect the Local and Remote Units carry electrical

current and should not be plugged into any other devices, as they may cause damage. We

strongly recommend marking the Ethernet cables you are using with this product at both

locations for easy identication.

Instruction Manual 5

Driver Installation

No driver installation is required for the video extender as it is an external hardware-only

solution, invisible to the computer system.

How to Use

The rotary wheel on the Remote Unit is used to access the various features available on the video

extender. There are two conguration mode available.

Mode A: This mode allows for selection of the physical connector on the unit to adjust (VGA or

3.5mm mini-jack) as well as volume control and video ON/OFF.

Mode B: This mode allows for adjustments to the video signal output, including Equalization,

Gain and RGB skew calibration.

To activate the conguration modes, follow these steps:

1. After installing and powering on the Local and Remote units, the Power LED on the Remote

Unit should light up solid green.

2. Press and hold the rotary wheel on the Remote Unit for several seconds and the set of

LED indicators under Output 1 and 2 should start ashing. This indicates the unit is in

conguration Mode A.

3. Continuing to hold the rotary wheel for another several seconds will cause the Equalizer/

Gain/Skew LEDs to start ashing. This indicates the unit is in conguration Mode B.

4. Release the rotary wheel when the unit enters the desired conguration mode.

NOTE: The unit will return to normal operating mode if left idle for 20 seconds.

Instruction Manual 6

Mode A Conguration

When in Mode A, each press of the rotary wheel will switch between the dierent physical ports

available on the unit (VGA and audio). When selected to a video output, rotating the wheel will

toggle the output ON or OFF. When selected to an audio output, rotating the wheel will increase

or decrease the volume output accordingly. The LED strength will reect the volume level (i.e.

brighter indicates higher volume).

Mode B Conguration

When in Mode B, each press of the rotary wheel switches between the dierent signal calibration

modes: equalization, gain, red skew, green skew and blue skew. Rotating the wheel in any of

these calibration modes will adjust the output signal accordingly.

NOTE: Before selecting Mode B, rst enter Mode A and select a video output connector. Then

when entering Mode B, the video calibration will aect that output only. If using both outputs

on the Remote unit, this process will need to be done to both separately.

EDID Copy

In some cases display problems may arise due to incorrect EDID communication between the

display device and the computer graphics card or insucient EDID data programmed into the

display device. The Local Unit provides an “EDID Copy” feature that allows the Local Unit to read

the necessary EDID information from the locally attached display device and then provide it, at

all times, to the attached video source. If no new EDID information is available from a display

device, a default prole built into the Local Unit is automatically provided.

Load Default EDID

When using a non-EDID compliant display device, the ST122UTPAL can automatically select

viable EDID data from the Unit’s default EDID prole to set the EDID information up. Users can

enable this default EDID prole by following the instructions below:

1. Press and Hold the button “EDID Copy” on the side panel of the Local Unit.

2. Plug in the provided power adapter to the Local Unit, while still holding the button.

3. Release the “EDID Copy” button immediately after one conrmation beep. The power LED

light will be steady green, indicating that the EDID copy (communication) is completed and

the default prole loaded.

Instruction Manual 7

4. Connect the monitor(s) to the output port on the Local Unit. The Local Unit is ready to

operate now.

Copy EDID (Port 1 only)

When using an EDID compliant display device, the ST122UTPAL’s EDID Copy function will enable

proper EDID communication between the monitor and the computer’s video card for optimal

video quality. Users can enable this EDID communication by following the instructions below:

1. Plug in the provided power adapter to the Local Unit.

2. Connect the EDID compliant display device to the “Port 1” output on the Local Unit.

3. Press and hold the “EDID Copy” button on the side panel of the Local Unit for about two (2)

seconds. Release button“EDID Copy” immediately after two conrmation beeps.

4. If one long beep occurs, it means that the display device is not properly connected to “Port 1”

on the Local Unit or does not contain proper EDID information. Please repeat Step2 to 3 to try

again or attempt with a dierent display device.

Inhaltsverzeichnis

Andere StarTech.com Extender Handbücher

StarTech.com

StarTech.com 110VDSLEXTGB Bedienungsanleitung

StarTech.com

StarTech.com USBthere USB221EXT Bedienungsanleitung

StarTech.com

StarTech.com VS321HDBTK Bedienungsanleitung

StarTech.com

StarTech.com ST121SHD50 Bedienungsanleitung

StarTech.com

StarTech.com ST121HDBTPW Bedienungsanleitung

StarTech.com

StarTech.com USB2G4LEXT2NA Bedienungsanleitung

StarTech.com

StarTech.com SV565UTPU Bedienungsanleitung

StarTech.com

StarTech.com 8STST12MHDLAN Bedienungsanleitung

StarTech.com

StarTech.com POEEXT1GAT Bedienungsanleitung

StarTech.com

StarTech.com 33FT-8K-HDMI-BOOSTER Bedienungsanleitung

StarTech.com

StarTech.com USB2001EXTV Bedienungsanleitung

StarTech.com

StarTech.com F35023-USB-EXTENDER Bedienungsanleitung

StarTech.com

StarTech.com IPUSB2HD3 Bedienungsanleitung

StarTech.com

StarTech.com ST121HDBT20L Bedienungsanleitung

StarTech.com

StarTech.com ST121R Bedienungsanleitung

StarTech.com

StarTech.com ST121UTPMINI Bedienungsanleitung

StarTech.com

StarTech.com ST121HDBT20L Bedienungsanleitung

StarTech.com

StarTech.com ST121R Bedienungsanleitung

StarTech.com

StarTech.com STDHVHDBT Bedienungsanleitung

StarTech.com

StarTech.com IPUSB2HD2 Bedienungsanleitung

StarTech.com

StarTech.com USB3004EXT2 Bedienungsanleitung

StarTech.com

StarTech.com ST121WHD2 Bedienungsanleitung

StarTech.com

StarTech.com ST121HDBT5 Bedienungsanleitung

StarTech.com

StarTech.com SV565UTP Bedienungsanleitung

Beliebte Extender Handbücher anderer Marken

SY HDBT-60T Bedienungsanleitung

Appsys ProAudio

Appsys ProAudio ADX-16 Bedienungsanleitung

Atlona

Atlona RS232 Bedienungsanleitung

IDK

IDK OPF-TH1000-A Bedienungsanleitung

Enable-IT

Enable-IT 824WP Bedienungsanleitung

Worx

Worx Landroid RadioLink WA0864 Technisches Datenblatt

TP-Link

TP-Link TL-WA730RE Bedienungsanleitung

Camplex

Camplex CMX-HDMI-SFPL Bedienungsanleitung

SC&T

SC&T HE03-4K Bedienungsanleitung

Marmitek

Marmitek MegaView70 Bedienungsanleitung

Samsung

Samsung SCS-26UC4 Bedienungsanleitung

Foxun

Foxun SX-GES24 Bedienungsanleitung

MuxLab

MuxLab 500771 Bedienungsanleitung

foxunhd

foxunhd SX-AEX01 Bedienungsanleitung

TERK Technologies

TERK Technologies LFIRX2 Bedienungsanleitung

Devolo

Devolo Audio Extender Handbuch

Edimax

Edimax EW-7438RPn V2 Bedienungsanleitung

Shinybow USA

Shinybow USA SB-6335T5 Bedienungsanleitung