STIEBEL ELTRON SB 150 Bedienungsanleitung

- 1 -

17 West Street

West Hatfield, MA 01088

Phone: (413) 247-3380 * (800) 582-8423

Fax: (413) 247-3369

E-mail: info@stiebel-eltron-usa.com

SB 150, SB 200

Glass Lined Indirectly Fired Water Heaters

With Single Heat Exchanger

INSTALLATION AND OPERATING INSTRUCTIONS

SB150 (40 gallon)

SB200 (50 gallon)

- 2 -

DANGER

•Water temperature over 125˚F can cause severe burns instantly or

death from scalds.

•Children, disabled and elderly are at highest risk of being scalded.

•Set the thermostat as low as practical. Settings the thermostat as

low as possible will reduce the risk of scalding and reduce energy

consumption.

•Feel water before showering or bathing.

•Special valves are available to provide anti-scald protection.

Consult a licensed plumber or the local pluming authority for more

information.

If the temperature and pressure relief valve on the SB tank opens

periodically, it may be due to thermal expansion in a closed water supply

system. Consult a licensed plumber, the local plumbing authority, or the

water supplier. Do not plug the Temperature and Pressure Relief Valve.

SB TANK PIPING WITH A “MIXING VALVE”

Usually, the maximum temperature of the outlet water will stay near

the setting of the thermostat. In some cases, however, hot water usage

patterns can cause the outlet water temperature to rise significantly

above the control settings.

The temperature of water going to the fixtures may be more

carefully controlled through the use of a mixing valve. This device blends

a controlled amount of cold water with the hot water from the tank to

provide a more constant temperature at the fixtures.

- 3 -

WARNING

There are no user serviceable parts on this product. Attempts to service

this product by someone other then a licensed plumber or heating

technician could void the warranty, cause property damage, personal

injury or loss of life.

A mixing valve does not eliminate the risk of scalding:

•Set the thermostat as low as practical.

•Feel water before bathing or showering.

•If anti-scald or anti-chill protection is required, use devices

specifically designed for such service. Install these devices in

accordance with their manufacturer’s instructions.

Install a new Temperature and Pressure Relief (“T & P”) Valve in the

tapping on the top of the tank marked “T&P VALVE”. Failure to do so

could result in property damage, personal injury or death.

•This Valve must comply with the Standard for Relief Valves and

Automatic Gas Shutoff devices for Hot Water Supply Systems (ANSI

Z21.22)

•No valve is to be placed between the T&P valve and the tank.

•Do not install valves, reducing couplings or other obstructions in the

relief valve discharge line.

•Do not install a T&P valve with a pressure settings in excess of 150 PSI

or a temperature setting in excess of 210˚F

•Pipe the discharge line to a location where hot water discharge will

not cause injury or damage.

•Do not run any portion of the discharge line through a location that

will be exposed to freezing temperatures.

•Pipe he discharge line to allow complete drainage of both the

discharge piping and the T&P valve.

Hydrogen gas can be produced in a hot water system that has not been

used for a long period of time (generally two weeks or more). Hydrogen

gas is extremely flammable. To prevent the possibility of injury under these

conditions, it is recommended that the hot water faucet be opened for

several minutes at the kitchen sink before you use any electrical

appliance, which is connected to the hot water system. If hydrogen is

present, there will probably be an unusual sound such as air escaping

through the pipe as hot water begins to flow. There should be no smoking

or open flame near the faucet at the time it is open.

- 4 -

I. Product description

The Stiebel Eltron SB series water heaters are indirectly fired designed to

generate hot water in conjunction with a solar collector system or a gas,

oil or pellet boiler using forced boiler water circulation. This indirect water

heater consists of an enameled steel tank in which a smooth coil is

located. A solar heated water/glycol mix or boiler water is pumped

through the heat exchanger coil and heats the water in the tank. The SB

series is not intended for use in heating any fluid other than water. It is also

not intended for use in gravity hot water heating systems.

II. Specifications

SB TANK

SB 150

SB 200

First hour rating (gal/hr)*

192

225

Boiler water output (btu / hr)

103, 149

116, 094

Boiler water flow (gal / min)

8.0

Coil head loss (ft w.c.)

2.6

Coil surface (sq. ft / m2)

12.1 / 1.12

14.3 / 1.32

Tank volume (gal / l)

39.0 / 147.63

52 / 196.84

Net weight (lbs / kg)

190 / 86.18

226 / 102.5

Filled weight (lbs / kg)

523 / 237.2

658 / 298.4

Connections (NPT)

Cool Drain

3/4 M

Boiler Supply

1 F

Boiler Return

1 F

Hot

3/4 M

Thermostat

3/4 F

Recirc

T&P Valve

3/4 F

Performance Specifications (I = B = R Certified Performance Ratings)

First Hour Rating (Gal/hr)

192.4

225.1

Cont. Draw Rating (Gal/hr)

158.0

178.2

Standby Heat Loss (F/hr)

1.9

1.3

Min Boiler Output (BTU/hr)

103, 149

116, 094

Boiler Water Flow (Gal/min)

8.0

•*First Hour Ratings are based on 58F˚ inlet water, 135F˚ hot water, and

180F˚ boiler supply water

•F = Female thread

•M = Male thread

- 5 -

Dimensions (in/cm)

Model

SB 150

SB 200

5 1/8 / 13.02

9 3/4 / 24.76

34 / 86.36

37 7/8 / 96.20

50 1/2 / 128.27

62 3/4 / 159.38

20 1/2

- 6 -

- 7 -

- 8 -

MAINTENANCE

The SB series tank is an extremely simple device and as such requires

very little maintenance. There are, however, several items that should be

checked out on an annual or as needed basis to ensure a reliable supply

of hot water:

1) On an annual basis, remove the jacket cover over the hand hole

and make sure that the hand hole gasket is leak-tight. On the 40

and 50-gallon sizes, this hand hole is located on the top of the SB

tank and is accessed by removing the two screws holding the cover

to the top of the SB tank.

2) Make sure that the rest of the boiler and domestic water piping is

free of leaks.

3) If there is an oil-lubricated circulator in the system, make sure that it

is lubricated as called for by the circulator manufacturer.

4) The SB tank depends upon the boiler for source of heat and is

therefore only as reliable as the boiler. Make sure that the boiler is

maintained in accordance with the boiler manufacturer’s

instructions.

5) All SB tanks are equipped with a sacrificial anode rod. This anode

rod helps to protect the SB tank from corrosion. This anode rod

should be inspected periodically and replaced if more than half of

the anode has been corroded away at any point in its length. The

rate at which the anode rod will deteriorate will depend upon the

quantity and chemistry of the water passing through the tank. In

general, an annual inspection of the anode rod is appropriate.

6) On an annual basis, check the operation of the Temperature and

Pressure Relief Valve by lifting the lever on the top of the valve and

confirming that water is released.

IMPORTANT

For the anode rod to work properly it must be electrically bonded to the

SB Tank. On the SB150 and SB200, this is done with two ground wires that

bond the anode rod to the clean-out cover and the clean-out cover to

the tank.

•Whenever the anode rod or clean out cover is serviced on the

SB150 or SB200, be sure that these ground wires are reconnected.

Failure to follow these precautions could result in premature failure of the

tank.

- 9 -

CAUTION

Stay away from the T&P Valve discharge piping when performing this

check to avoid contact with hot water. Also make sure that water from

the discharge will not damage property before performing this test.

Stiebel Eltron warrants to the original owner that the SB Storage tank for solar hot

water systems will be free from defects in workmanship and materials for a period of ten

(10) years from the date of purchase.

Should the part(s) prove to be defective under normal use during this period, Stiebel

Eltron, Inc. will be responsible for replacement of the defective part(s) only. Stiebel Eltron,

Inc. will not be liable for any costs of transportation, removal, reinstallation, or any other

labor or freight charges that may arise in connection with a warranty claim or any incidental

or consequential expenses.

This warranty does not apply:

to conditions resulting from a failed component or part that is not part of the solar

storage tank

to freeze damage

to conditions resulting from misuse, abuse, neglect, accident, or alteration

liquids deleterious to copper tubing, including improperly applied or maintained heat

to excessive pressure

circumstances beyond the manufacturer's control

to installation methods which do not conform to relevant national, state or local

codes and ordinances, good industry practices or applicable manuals, diagrams,

technical bulletins or written installation instructions; and, to applications other than

medium temperature.

from Stiebel Eltron, Inc. The owner shall be required to show proof of purchase date, and

to pay all transportation costs to return the defective part(s) for repair or replacement.

WARRANTY

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere STIEBEL ELTRON Boiler Handbücher

STIEBEL ELTRON

STIEBEL ELTRON UFP 5 t Si Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON DHB-E 13 LCD Technisches Datenblatt

STIEBEL ELTRON

STIEBEL ELTRON DHB-E 11 LCD Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON SHD 30 S Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON HSBC 300 cool Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON SHZ 30 LCD Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON DHE Connect 18/21/24 Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON SimpleX Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON IS 35 E Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON Eltronom SHU 5 S Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON SNU 10 SL comfort Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON Tempra 20 b Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON TEMPRA 12 TREND Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON SH 10 S Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON Accelera 300 Technisches Datenblatt

STIEBEL ELTRON

STIEBEL ELTRON DHB-E 13 AU Kurzanleitung

STIEBEL ELTRON

STIEBEL ELTRON DEL 18 SL i 25A Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON DHC-E 30 Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON DHE 18 SL LABS Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON DHB-E 18 SLi 25 A electronic Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON SHC 4 Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON SH 10 SL Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON SHU 10 SLi comfort Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON IS 5-1 E Bedienungsanleitung

Beliebte Boiler Handbücher anderer Marken

Kenmore

Kenmore 153.582400 Bedienungsanleitung

clage

clage E-Mini Series Bedienungsanleitung

Toyotomi

Toyotomi Oil Miser OM-180 Bedienungsanleitung

Bradford White

Bradford White EF Series Bedienungsanleitung

Eccotemp

Eccotemp 40-H Bedienungsanleitung

Dimplex

Dimplex ECSd125-580 Leitfaden

Dux

Dux 32FCR6N Bedienungsanleitung

Noritz

Noritz N-132M Gebrauchsanweisung

TESY

TESY GCV7/4S 10047 Technisches Datenblatt

A.O. Smith

A.O. Smith Gphe 50 Bedienungsanleitung

Toyotomi

Toyotomi Oil Miser OM-148 (Type D) Fehlerbehebungshandbuch

Koryo

Koryo KWHZF15Y Bedienungsanleitung

Pentair

Pentair PSC-14-4-02 Bedienungsanleitung

GE 40M06AAG Montageanleitung

Thermor

Thermor AEROMAX SPLIT 2 Bedienungsanleitung

American Hometec

American Hometec AHQ-B03X Bedienungsanleitung

PVI

PVI MAXIM Bedienungsanleitung

Sunerg Solar Energy

Sunerg Solar Energy Calor Top 200D Betriebsanleitung