SunSetter 900XT Bedienungsanleitung

RETRACTABLE AWNINGS

For Technical Support visit usat www.sunsetter.com/ownerscorner orCall Toll Free

800-670-7071 • Fax 877-224-4944

Outer and Inner Arm With Rafter Set Replacement

900XT and 1000XT Awning

Tools Needed: 7/16” wrench, 7/16” socket and ratchet, 7/32” Allen wrench, & flat screwdriver.

Parts Supplied: Outer/Inner Arm (Left or Right), Rafter Set (Left or Right)

WARNING: FAILURE TO FOLLOW THESE INSTRUCTIONS CAN RESULT IN PERSONAL INJURY!! PLEASE READ

THESE INSTRUCTIONS IN ITS ENTIRETY BEFORE ATTEMPTING TO COMPLETE THIS PROCESS.

PLEASE NOTE THAT LEFT AND RIGHT REFERENCES ARE AS YOU ARE FACING THE HOUSE.

1. Using the Hand Crank Wand, unroll the Awning until the Fabric is

completely extended. Do not lock the Rafters. Place a chair or box

under the Roller Bar for support. See Figure 1.

Note:If Arms and or Rafters on BOTH sides are to be replaced, more

than one chair or box should be used to evenly and safely support the

Roller Bar. See Figure 1.

Note:Take notice of the positioning of the Drive Unit and Crank Loop.

See Figure 5.

2. On the side needing replacement, remove the 1/4" nut and bolt that

secures the Rafter End to the Upper Bracket. See Figure 2

3. Carefully fold the Rafter set on top of the Arm.

4. Using a 7/32” Allen wrench, remove the Flat-head Cap Bolt that secures

the Arm and Rafter to the Roller Assembly. See Figure 3.

5. Separate the Roller from the end of the Rafter and Arm. See Figure 3.

Note: If you are replacing the Right Rafter Set, make sure that the

Drive Unit is oriented so that the Crank Loop is pointing towards the

HOUSE. See Figure 4.

6. Remove the old Rafter Set from the Awning and replace with the new

Rafter Set.

7. Unlatch the bottom of the Arm from the Wall Bracket on the house. See

Figure 4.

House

Roller Bar resting on one

or two chairs as needed

Figure 1

Figure

Roller Assembly

Arm

and

Rafter

Flat-head

Bolt

Figure 2

/4” nut and bolt

8. Transfer the extra Acorn Nut Stop from the old Inner Arm to the new

Inner Arm and tighten with a 7/16” wrench. See Figure 5.

9. Latch the bottom of the replacement Arm into the Wall Bracket on

the house. See Figure 4.

Note: If you are replacing the right hardware, make sure to orient the

Drive Unit so that the Crank Loop is pointing towards the HOUSE. See

Figures 6 and 6a.

10. Assemble the ends of the Rafter and Arm to the Roller and secure

with the Flat-head Cap Bolt. Tighten with a 7/32” Allen wrench. See

Figure 3.

11. Secure the Rafter End to the Upper Bracket with the 1/4" bolt and

nut, and tighten with a 7/16" wrench and 7/16" socket. See Figure 2.

12. Test the Awning for proper operation.

December 2, 2021 ©SunSetter Products, a Massachusetts Limited Partnership, 184 Charles Street, Malden, MA02148 INS053-InnerOuterArmWithRafter_Replacement

Figure

Figure 6a

Crank

Loop

Drive

Gear

Rafter

Arm Assembly

Figure 6

Andere Handbücher für 900XT

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere SunSetter Zubehör Handbücher

SunSetter

SunSetter Vista Series Bedienungsanleitung

SunSetter

SunSetter 900XT Bedienungsanleitung

SunSetter

SunSetter VISTA Betriebsanleitung

SunSetter

SunSetter Oasis Leitfaden

SunSetter

SunSetter Oasis Leitfaden

SunSetter

SunSetter 900XT Bedienungsanleitung

SunSetter

SunSetter Platinum Plus Series Originalbetriebsanleitung

SunSetter

SunSetter Wireless Wind Sensor Bedienungsanleitung

SunSetter

SunSetter EASYSHADE Gebrauchs- und Pflegehandbuch

SunSetter

SunSetter 900XT Installationsanleitung

SunSetter

SunSetter Motorized Series Originalbetriebsanleitung

SunSetter

SunSetter PRO Bedienungs- und Sicherheitshinweise

SunSetter

SunSetter EASYSHADE Gebrauchs- und Pflegehandbuch

SunSetter

SunSetter Oasis Leitfaden

SunSetter

SunSetter EASYSHADE Originalbetriebsanleitung

SunSetter

SunSetter Oasis Leitfaden

SunSetter

SunSetter OASIS Series Bedienungsanleitung

SunSetter

SunSetter Oasis Leitfaden

SunSetter

SunSetter EASYSHADE Gebrauchs- und Pflegehandbuch

SunSetter

SunSetter Gaviota Kurzanleitung

SunSetter

SunSetter Platinum Plus Leitfaden

SunSetter

SunSetter Motorized PRO Leitfaden

SunSetter

SunSetter 900XT Gebrauchs- und Pflegehandbuch

SunSetter

SunSetter EASYSHADE Leitfaden

Beliebte Zubehör Handbücher anderer Marken

Hillco

Hillco 2810 Bedienungsanleitung

Siemens

Siemens QSA2700D Bedienerhandbuch

Contours

Contours ZY024 Bedienungsanleitung

Saivod

Saivod VS621 Bedienungsanleitung

Virtuox

Virtuox VirtuCLEAN 2.0 Bedienungsanleitung

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Bedienungsanleitung

Z-Wave

Z-Wave HSD-200Z Bedienungsanleitung

turck

turck FMX-IM-2UPLI63FX Bedienungsanleitung

Decagon Devices

Decagon Devices 10HS Bedienungsanleitung

UPPAbaby

UPPAbaby Cup Holder Bedienungsanleitung

Elko

Elko SmartSensor Leakage Wireless Bedienungsanleitung

Grizzly

Grizzly H8371 Bedienungsanleitung

Panasonic

Panasonic HG-T Series Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 250 Series Referenzhandbuch

DigiDesign

DigiDesign 888/24 I/O Bedienungsanleitung

PROZIS

PROZIS QUAY Bedienungsanleitung

patagonia

patagonia PSI Vest Bedienungsanleitung

SFC Energy

SFC Energy EFOY GO! Bedienungsanleitung