SunSetter OASIS Series Bedienungsanleitung
For Technical Support visit us at hp://ownerscorner.sunseer.com
or Call Toll Free 800-670-7071 • Fax 877-224-4944
©SunSeer Products, 184 Charles Street, Malden, MA 02148
PRODUCTS
Protecve Cover - OASIS Freestanding Awning
Installaon Instrucons
‘Helper Needed’
WARNING: FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN PERSONAL
INJURY.
Tools Needed: Step Ladder (2)
Parts Included:12 Oasis 16 Oasis
Cover 1 1
Safety Clip 7 9
Cord Lock 7 9
Gear 7 9
Cord 7 9
Cord Lock
Safety Clip
Gear (white or black)
Cord
Cover
Parts Supplied:Safety Clip, Cord Lock, Gear, and Cord (Safety Clip Kit)
7 Safety Clip Kits each for 12ft model, 9 Safety Clip Kits each for 16ft
model. See Figure 1.
©SunSeer Products, 184 Charles Street, Malden, MA 02148
RETRACTABLE AWNINGS
For Technical Support visit us at http://ownerscorner.sunsetter.com
or Call Toll Free 800-670-7071 • Fax 877-224-4944
Instructions for Use of Breakaway Safety Clips and Oasis Awning Cover
*REQUIRED *
2.
3.
4.
Thread a Cord through one of the safety Clip handles. See Figure 2.
Slide the two ends of the Cord through the Cord Lock from the
smaller (flat edge) side to the larger (curved) side. (Do not pull the
entire Cord through.) See Figure 3.
Hold the Cord Lock in the center of the Cord and separate the two
ends of the Cord. See Figure 4.
Slide the Gear into the large (curved) side of the Cord Lock until the
Gear pops into place. Be sure that the part of the Gear that
protrudes is aligned with the slot in the Cord Lock. See Figure 5.
5. Repeat with remaining Safety Clips, Cords, Gears, and Cord Locks.
Figure 3
Cord through Cord Lock
Figure 4
Cord Lock
Ends of
Cord
Figure 5
Gear in
Cord Lock
Cord Lock
Safety Clip
Gear (White or Black)
Cord
Figure 1 - Parts Supplied (Safety Clip Kit)
Figure 2
Cord through Clip Handle
SUDDEN IMPACT HAZARD
•USE ONLY provided Breakaway Safety Clips to fasten the Protective Cover around the Awning.
•DO NOT USE other tie-downs in addition to or instead of the provided Breakaway Safety Clips.
•SECURE the Breakaway Safety Clips as directed.
•NEVER place a ladder or stand in front and at the level of the Front Bar of the Awning.
Failure to follow these instructions can present risk of DEATH or SERIOUS INJURY from being struck by an
Awning suddenly opening while removing tie-downs.
WARNING
Gear (White or Black)
1.
Assembly of Breakaway Safety Clips
SunSeer Products, a Massachuses Limited Partnership, 184 Charles Street, Malden, MA 02148
July 29, 2019 INS065-Cover_OASIS.pdf
Figure 8
Figure 6
Grommet
Cord Loop
Figure 7
Safety
Clip
Cord
Lock
Figure 9
Installation and First Use of Breakaway Safety Clips
Detaching Breakaway Safety Clips
1. Verify Awning is closed and
unplugged.
2. Position yourself under the Awning
and detach each Safety Clip, one at a
time.
3. DO NOT REMOVE the Cord Locks
from the Cover.
4. Plug in the electrical cord to use the
Awning.
Figure 10
knot
SUDDEN IMPACT HAZARD
•USE ONLY provided Breakaway Safety Clips to fasten the Protective Cover around the Awning.
•DO NOT USE other tie-downs in addition to or instead of the provided Breakaway Safety Clips.
•SECURE the Breakaway Safety Clips as directed.
•NEVER place a ladder or stand in front and at the level of the Front Bar of the Awning.
Failure to follow these instructions can present risk of DEATH or SERIOUS INJURY from being struck by an
Awning suddenly opening while removing tie-downs.
WARNING
1. Close the Oasis and unplug it from the electric outlet.
2. The Cover will be installed on top of the Oasis when the
installation of the Safety Clip Tie-Downs is complete.
3. Remove the Protective Cover from its packaging. Orient the Cover
on a clean work surface, so that the sewn hem is facing down.
4. Locate the Breakaway Safety Clips.
5. Form a loop in the Cord and pass it through a Grommet. See
Figure 6. Pass the Cord with Safety Clip and Cord Lock through
the loop (see Figure 7) and pull it snug. See Figure 8.
6. Repeat for each Breakaway Safety Clip on one side of Cover.
7. Lay the Cover across the top of the fully closed Oasis, sewn hem
facing down.
8. Attach the Safety Clip to the other side of the Cover, along the hem by
each Grommet location, passing it underneath the Oasis square bar. See
Figure 9.
9. Cinch the Cord Lock to the desired snugness, then create a knot using the
two cord ends so the knot is located approximately 1 inch from the Cord
Lock. See Figure 10.
10. Trim the excess Cord close to the knot at each location. See Figure 10.
11. Call 800-670-7071 for Free replacement Cord Locks if necessary.
Loop
Dieses Handbuch passt für folgende Modelle
2
Inhaltsverzeichnis
Andere SunSetter Zubehör Handbücher
SunSetter
SunSetter EASYSHADE Gebrauchs- und Pflegehandbuch
SunSetter
SunSetter Oasis Leitfaden
SunSetter
SunSetter 900XT Gebrauchs- und Pflegehandbuch
SunSetter
SunSetter EASYSHADE Gebrauchs- und Pflegehandbuch
SunSetter
SunSetter Oasis Gebrauchs- und Pflegehandbuch
SunSetter
SunSetter Wireless Wind Sensor Bedienungsanleitung
SunSetter
SunSetter PRO Bedienungs- und Sicherheitshinweise
SunSetter
SunSetter Gaviota Kurzanleitung
SunSetter
SunSetter Platinum Plus Leitfaden
SunSetter
SunSetter Motorized PRO Leitfaden
SunSetter
SunSetter Oasis Leitfaden
SunSetter
SunSetter EASYSHADE Gebrauchs- und Pflegehandbuch
SunSetter
SunSetter Motorized Series Originalbetriebsanleitung
SunSetter
SunSetter 900XT Installationsanleitung
SunSetter
SunSetter VISTA Originalbetriebsanleitung
SunSetter
SunSetter Platinum Plus Series Originalbetriebsanleitung
SunSetter
SunSetter VISTA Betriebsanleitung
SunSetter
SunSetter EASYSHADE Leitfaden
SunSetter
SunSetter VISTA Kurzanleitung
SunSetter
SunSetter Oasis Leitfaden
