Supermicro K1048-RT Bedienungsanleitung
Microserver
K1048-RT
USER’S MANUAL
Revision 1.0c
The information in this User’s Manual has been carefully reviewed and is believed to be accurate.
The vendor assumes no responsibility for any inaccuracies that may be contained in this document,
makes no commitment to update or to keep current the information in this manual, or to notify any
person or organization of the updates. Please Note: For the most up-to-date version of this
manual, please see our web site at www.supermicro.com.
Super Micro Computer, Inc. ("Supermicro") reserves the right to make changes to the product
described in this manual at any time and without notice. This product, including software and
documentation, is the property of Supermicro and/or its licensors, and is supplied only under a
license. Any use or reproduction of this product is not allowed, except as expressly permitted by
the terms of said license.
IN NO EVENT WILLSUPERMICRO BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL,
SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR INABILITY TO
USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES. IN PARTICULAR, SUPERMICRO SHALL NOT HAVE LIABILITY FOR ANY
HARDWARE, SOFTWARE, OR DATASTORED OR USED WITHTHE PRODUCT, INCLUDING THE
COSTS OF REPAIRING, REPLACING, INTEGRATING, INSTALLING OR RECOVERING SUCH
HARDWARE, SOFTWARE, OR DATA.
Any disputes arising between manufacturer and customer shall be governed by the laws of Santa
Clara County in the State of California, USA. The State of California, County of Santa Clara shall
be the exclusive venue for the resolution of any such disputes. Super Micro's total liability for all
claims will not exceed the price paid for the hardware product.
FCC Statement: This equipment has been tested and found to comply with the limits for a Class
A digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the manufacturer’s instruction manual, may cause harmful
interference with radio communications. Operation of this equipment in a residential area is likely
to cause harmful interference, in which case you will be required to correct the interference at your
own expense.
California Best Management Practices Regulations for Perchlorate Materials: This Perchlorate
warning applies only to products containing CR (Manganese Dioxide) Lithium coin cells. “Perchlorate
Material-special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate”
WARNING: Handling of lead solder materials used in this
product may expose you to lead, a chemical known to
the State of California to cause birth defects and other
reproductive harm.
Manual Revision 1.0c
Release Date: June 23, 2016
Unless you request and receive written permission from Super Micro Computer, Inc., you may not
copy any part of this document.
Information in this document is subject to change without notice. Other products and companies
referred to herein are trademarks or registered trademarks of their respective companies or mark
holders.
Copyright © 2016 by Super Micro Computer, Inc.
All rights reserved.
Printed in the United States of America
iii
Preface
Preface
About This Manual
This manual is written for professional system integrators and PC technicians. It
provides information for the installation and use of the K1048-RT. Installation and
maintenance should be performed by experienced technicians only.
The K1048-RT is a high-end Microserver unit based on the SC801LTS-R406KP
1U rackmount server chassis, a dual 10G Broadcom BMC-53347 LAN switch and
twelve (12) internal hot-swap Ethernet 3.5" HDD drives. The K1048-RT has an
IPMI LAN port, two 10G LAN ports, a serial management port and two redundant
400 Watt power supplies.
Manual Organization
Chapter 1: Introduction
The first chapter provides a checklist of the main components included with
the server system and describes the main features of the mainboard and the
SC801LTS-R406KP chassis.
Chapter 2: Server Installation
This chapter describes the steps necessary to install the Microserver K1048-RTinto
a rack and check out the configuration prior to powering up the system.
Chapter 3: System Interface
Refer here for details on the system interface, which includes the functions and
information provided by the control panel on the chassis as well as other LEDs
located throughout the system.
Chapter 4: System Safety
You should thoroughly familiarize yourself with this chapter for a general overview
of safety precautions that should be followed when installing and servicing the
Microserver K1048-RT.
Chapter 5: Advanced Serverboard Setup
Chapter 5 provides detailed information on the mainboard, including the locations
and functions of connections, headers and jumpers.
K1048-RT Microserver User's Manual
iv
Chapter 6: Advanced Chassis Setup
Refer to Chapter 6 for detailed information on the SC801LTS-R406KP server
chassis. You should follow the procedures given in this chapter when installing,
removing, or reconfiguring drives and when replacing system power supply units
and cooling fans.
Appendix A: System Specifications
Appendix B: Storage Monitoring IPMI Page
v
Notes
Preface
vi
Table of Contents
Chapter 1 Introduction
1-1 Overview ......................................................................................................... 1-1
1-2 Server and Switch Features ........................................................................... 1-2
Microserver Storage System........................................................................... 1-2
Ethernet Ports................................................................................................. 1-2
Onboard Controllers/Ports ..............................................................................1-3
Other Features................................................................................................1-3
1-3 Server Chassis Features ................................................................................1-3
System Power.................................................................................................1-3
Microserver Disk Subsystem...........................................................................1-3
Front Control Panel.........................................................................................1-4
I/O Ports..........................................................................................................1-4
Cooling System...............................................................................................1-4
Mounting Rails ................................................................................................1-4
1-4 Contacting Supermicro....................................................................................1-6
Chapter 2 Server Installation
2-1 Overview ......................................................................................................... 2-1
2-2 Unpacking the System.................................................................................... 2-1
2-3 Preparing for Setup.........................................................................................2-1
Choosing a Setup Location............................................................................. 2-2
2-4 Warnings and Precautions..............................................................................2-2
Rack Precautions............................................................................................2-2
Server Precautions.......................................................................................... 2-2
Rack Mounting Considerations....................................................................... 2-3
Ambient Operating Temperature................................................................2-3
Reduced Airflow .........................................................................................2-3
Mechanical Loading ...................................................................................2-3
Circuit Overloading.....................................................................................2-3
Reliable Ground .........................................................................................2-4
2-5 Installing the System into a Rack ...................................................................2-4
Sliding the Chassis onto the Rack Rails.........................................................2-6
2-6 Power-up/Power-down Sequence................................................................... 2-7
K1048-RT Microserver User's Manual
vii
Chapter 3 System Interface
3-1 Overview ......................................................................................................... 3-1
3-2 Control Panel Buttons.....................................................................................3-2
3-3 Control Panel LEDs ........................................................................................ 3-2
Chapter 4 Standardized Warning Statements for AC Systems
4-1 About Standardized Warning Statements....................................................... 4-1
Warning Definition...........................................................................................4-1
Installation Instructions.................................................................................... 4-4
Circuit Breaker ................................................................................................4-5
Power Disconnection Warning........................................................................ 4-6
Equipment Installation.....................................................................................4-8
Restricted Area................................................................................................ 4-9
Battery Handling............................................................................................ 4-10
Redundant Power Supplies .......................................................................... 4-12
Backplane Voltage ........................................................................................4-13
Comply with Local and National Electrical Codes........................................4-14
Product Disposal...........................................................................................4-15
Hot Swap Fan Warning.................................................................................4-16
Power Cable and AC Adapter ......................................................................4-18
Chapter 5 Microserver System Setup
5-1 Rear I/O Ports.................................................................................................5-1
5-2 Mainboard Details........................................................................................... 5-2
5-3 Connector Definitions...................................................................................... 5-3
5-4 Onboard Indicators.......................................................................................... 5-4
5-5 System Battery................................................................................................5-5
Chapter 6 Advanced Chassis Setup
6-1 Static-Sensitive Devices..................................................................................6-1
Precautions ..................................................................................................... 6-1
6-2 Removing the Power Cord.............................................................................. 6-2
6-3 Control Panel ..................................................................................................6-2
6-4 Removing the Chassis Cover .........................................................................6-3
6-5 Installing and Replacing Hard Drives..............................................................6-4
6-6 System Fans................................................................................................... 6-7
6-7 Power Supply..................................................................................................6-8
Appendix A System Specifications
Table of Contents
viii
K1048-RT Microserver User's Manual
Appendix B Storage Monitoring IPMI Page
Using the IPMI Screen....................................................................................B-1
I2C Commands...............................................................................................B-2
OEM IPMI Commands to Get Ethernet Hard Drive Information.....................B-2
Standards...................................................................................................B-2
Byte Range.................................................................................................B-3
IP Address..................................................................................................B-4
MAC Address .............................................................................................B-5
Chapter 1
Introduction
1-1 Overview
The K1048-RT Microserver is a high-end switch/storage server comprised
of three main subsystems: the SC801LTS-R406KP 1U server chassis the
Broadcom BMC-53347 switch system and twelve (12) 3.5" Ethernet hard drives.
Please refer to our web site for information on operating systems that have been
certified for use with the system (www.supermicro.com).
An illustration of the overview IP assignment flow for this switch/storage server is
shown below.
Chapter 1: Introduction
1-1
Storage System Manager
(Object Storage Platform)
Using the API, this platform sets fault
tolerance and key/value data placement.
Figure 1-1. Overview IP Assignment Flow
In addition to the system mainboard and chassis, various hardware components
have been included with the K1048-RT server, as listed below:
• Six (6) 40x28-mm 13K RPM 4-pin PWM fans (FAN-0065L4)
• One (1) 85-cm 16-pin to 16-pin ribbon 28AWG front control cable
(CBL-CDAT-0648)
• Two (2) 8-pin to 3 2x2(10-cm) power cable for SC801L (CBL-PWEX-0636)
1-2
K1048-RT Microserver User's Manual
• HDD Components:
Twelve (12) hot-swap 3.5" 4TB 5.9K RPM 64MB Cache, Ethernet HDD's
(HDD-T4000-ST4000NK000101)
• One (1) rails set (MCP-290-00066-0N)
Note: For your system to work properly, please follow the links below to download
all necessary drivers/utilities and the user’s manual for your server.
• Supermicro product manuals: http://www.supermicro.com/support/manuals/
• Product drivers and utilities: ftp://ftp.supermicro.com
• Product safety information:
http://super-dev/about/policies/safety_information.cfm
• If you have any questions, please contact our support team at:
1-2 Server and Switch Features
At the heart of the K1048-RT server/switch lies dual Broadcom™ BMC-53347
10Gbps communication chips and system for communicating and servicing the
Ethernet hard-disk drives. Although these systems are mounted on a system
mainboard, this mainboard does not contain any CPUs, chipset or memory and
therefore will not be covered in this manual.
The sections below cover the main server and switch features of the K1048-RT
system (see Figure 1-1 for a block diagram of the chipset).
Microserver Storage System
The K1048-RT system ships fully integrated with twelve (12) dual ported 4TB
7200-rpm Ethernet drives (48TB). Redundant 1G Ethernet downstream connections
allow for resilient multi-path access to the key/value pair HTTP storage interface
built into each drive.
Ethernet Ports
Two Broadcom BMC-53347 10-Gigabit (1/10 Gbps) Ethernet Controllers are
integrated into the mainboard in the K1048-RT server. Additionally an IPMI LAN
port is provided. The system's AST2400BMC (Baseboard Management Control)
chip supports IPMI 2.0.
Inhaltsverzeichnis
Andere Supermicro Server Handbücher
Supermicro
Supermicro SUPERSERVER 6014P-32 Bedienungsanleitung
Supermicro
Supermicro A+ Server AS-1115S-FWTRT Bedienungsanleitung
Supermicro
Supermicro SUPERSERVER 2028TP-HC0R Bedienungsanleitung
Supermicro
Supermicro SuperServer 2029P-C1R Bedienungsanleitung
Supermicro
Supermicro AS-2114S-WN24RT Bedienungsanleitung
Supermicro
Supermicro SUPERSERVER 1028R-TDW Bedienungsanleitung
Supermicro
Supermicro SuperBlade SBI-610P-1C2N Bedienungsanleitung
Supermicro
Supermicro SuperServer SYS-2029U-E Series Bedienungsanleitung
Supermicro
Supermicro SuperServer 6028U-E1CNR4T+ Bedienungsanleitung
Supermicro
Supermicro SuperStorage 1029P-NMR36L Bedienungsanleitung
Supermicro
Supermicro Storage SuperServer SSG-640SP-DE1CR90 Bedienungsanleitung
Supermicro
Supermicro SUPERSERVER 8016B-TF Bedienungsanleitung
Supermicro
Supermicro SuperServer 1027R-WTRFTP Bedienungsanleitung
Supermicro
Supermicro SuperServer 1029U-E Series Bedienungsanleitung
Supermicro
Supermicro SuperServer SYS-211TP-HPTR Bedienungsanleitung
Supermicro
Supermicro SuperStorage SSG-610P-ACR12N4H Bedienungsanleitung
Supermicro
Supermicro SUPERSERVER 6015C-NT Bedienungsanleitung
Supermicro
Supermicro AS-2125HS-TNR Bedienungsanleitung
Supermicro
Supermicro SUPERSERVER 5018A-MHN4 Bedienungsanleitung
Supermicro
Supermicro SuperServer 5039MS-H12TRF Bedienungsanleitung
Beliebte Server Handbücher anderer Marken
iRobo
iRobo IPC2U Bedienungsanleitung
Nortel
Nortel 1000 Con?guration guide Bedienungsanleitung
Asus
Asus AP7500 Bedienungs- und Wartungshandbuch
Avid Technology
Avid Technology AirSpeed 5000 Bedienungsanleitung
HP
HP Integrity rx2600 Installationsanleitung
Milestone
Milestone Husky IVO 350T Bedienungsanleitung