Supermicro SYS-F629P3-RTB Betriebsanleitung

Information for Lot 9 of ErP (Ecodesign)

This addendum addresses European Union (EU) Ecodesign requirements for servers and storage

products. All data and ratings within this addendum are in reference only to the Supermicro product(s) in

the manual. The below information conforms to requirements laid down in Annex II of the Commission

Regulation 2019/424.

3(1)(a): See Section 1.1 of the system manual for the product type.

3(1)(b): See the title page and preface of the system manual for the trademark and

manufacturer’s address.

3(1)(c): See the title page of the system manual for product model number(s).

3(1)(d): See the serial number on the physical system to determine the year of manufacture.

3(1)(e-j): PSU Efficiency and Power Factor Value (Table) (From 80 Plus report)

PSU Model #: PWS-706P-1R

Watts: 2200W

PSU Efficiency

Power

Factor

% of Rated Load

10 % 20 % 50 % 100 %

50 %

Single Output (AC-DC)

93.3%

96.07%

96.26%

94.37 %

0.99

System (EUT) Efficiency in Idle State Power (Table)

Representative

Configurations

Measured Idle State

Power (W)

Calculated Idle Power

Allowance per Node (W)

High-End Performance

Configuration

406.1

472.44

Typical Configuration

361.9

448.94

Low-End Performance

Configuration

332.6

196.16

System (EUT) Efficiency in Active State Power (Table)

Representative

Configurations

Active State

Efficiency Score

(Effserver)

Minimum Active State

Efficiency for 2-Socket

Server

High-End Performance

Configuration

Typical Configuration

39.1

Low-End Performance

Configuration

18.9

3(1)(k): The operating condition class is A2.

Dry bulb temp °C

Humidity range, non-condensing

Operatin

condition

Allowable

range

Recom

mende

d range

Allowable range

Recommended

range

Maxdew

point (°C)

Maximum

rate of

change

(°

C/hr)

15- 32

18-27

–

12 °C Dew Point (DP) and

8 %

relative humidity (RH) to

17 °C DP and 80 % RH

–

9 °C DP to

15 °C DP and

60 % RH

5/20

10-35

18-27

–

12 °C DP and 8 % RH to

21 °

C DP and 80 % RH

Same as A1

5/20

5-40

18-27

–

12 °C DP and 8 % RH to

24 °

C DP and 85 % RH

Same as A1

5/20

5-45

18-27

–

12 °C DP and 8 % RH to

24 °

C DP and 90 % RH

Same as A1

5/20

3(1)(l): The idle state power at the higher boundary temperature of the operating conditions

class is 406.1W.

3(1)(m): The active state efficiency and performance is 39.

3(1)(n): There are two methods by which a user can securely delete data from this system. The

user performing secure data deletion should be an IT professional.

The first is with a Unified Extensible Firmware Interface (UEFI) shell utility. This utility

works on X10/X11/H11/H12/M11 motherboard series with onboard SATA/NVMe

devices. Any user may access and download this utility through following link:

https://www.supermicro.com/about/policies/disclaimer.cfm?url=/wftp/utility/Lot9_Sec

ure_Data_Deletion_Utility/

Download the shell utility package and extract it to a USB flash drive, then plug the drive

into the server for which secure data deletion is necessary. Then turn the system on.

Navigate to the BIOS setup menu, then place the server system into the UEFI shell

environment. Follow the instructions in the README file to invoke the utility and

complete the deletion.

The second method is through the secure data deletion tool provided by the original

manufacturer of the hard drive. This should be used in a scenario where the shell utility

is not applicable. Each manufacturer should have the tool available on their website. If

needed, please look on the hard drive label for the name of the manufacturer and

model information.

3(1)(o): List of recommended combinations of FatTwin servers with chassis: N/A.

3(1)(p) List of all current SKUs within this product family: SYS-F629P3-RTB.

3(3)(a): There is no use of cobalt in batteries in this product.

The indicative weight range of neodymium in the HDD is 0.0 if manufactured by Western

Digital, and is between 5-25 grams if manufactured by Seagate.

3(3)(b): Please see the disassembly instructions on the next pages.

Illustrated System Disassembly Instructions

Please note:

All the illustrations in the below disassembly instructions are for demonstration only.

Components shown here may not match exactly with the components in your system.

CAUTION: Always power off the system and unplug the power cord(s) first

before disassembling the system!

1. Data Storage Devices

Type and number of fastenings:

One (1) latch.

Tools required:

None.

Procedure:

Release the hard drive tab. Remove the hard drive out of the chassis.

Data storage drives in the carrier:

2. Memory

Type and number of fastenings:

Two (2) latches per memory module.

Tools required:

None.

Procedure:

Press both release tabs on the ends of the memory module to unlock it. Once the

module is loosened, remove it from the memory slot.

3. Processor

Type and number of fastenings:

Four (4) T30 Torx screws.

Tools required:

Screwdriver with T30 Torx bit.

Procedure:

Remove the screws in the sequence of 4, then 3, then 2, then 1, as marked in the

illustration below. After removing the screws, lift the processor heatsink module off the processor

socket. Unsnap corners A and B, then C and D of the latch. Push the latch out from the bottom.

4. Motherboard

Type and number of fastenings:

Twelve (12) Phillips screws for SYS-F619P2/3-FT.

Tools required:

Screwdriver with PH2 bit.

Procedure:

Remove all Phillips screws. Lift the motherboard from its base.

5. Expansion Card/Graphics Card

Type and number of fastenings:

One (1) Phillips screw.

Tools required:

Screwdriver with PH2 bit.

Procedure:

Remove the Phillips screw. Open the rear window latch and carefully remove the

expansion card from the riser card slot, lifting it up and away from the system.

6. Power Supply Module

Type and number of fastenings:

One (1) latch per module.

Tools required:

None.

Procedure:

Unplug the power cord from the power supply. Push the release tab on the back of

the power supply module to the side and pull the module straight out.

7. Chassis Cover

Type and number of fastenings:

One (1) Phillips screw.

Tools required:

Screwdriver with PH2 bit.

Procedure:

Remove the screw securing the cover of the node.

Inhaltsverzeichnis

Andere Supermicro Server Handbücher

Supermicro

Supermicro SuperServer SYS-520P-WTR Bedienungsanleitung

Supermicro

Supermicro SuperServer 6014H-8 Bedienungsanleitung

Supermicro

Supermicro S-1600 R4 Gebrauchs- und Pflegehandbuch

Supermicro

Supermicro SUPERSERVER 2026T-DE2R24L Bedienungsanleitung

Supermicro

Supermicro SuperServer 5039MS-H12NR Bedienungsanleitung

Supermicro

Supermicro SUPERSERVER 2028TR-HTR Bedienungsanleitung

Supermicro

Supermicro SuperServer 5019C-MHN2 Bedienungsanleitung

Supermicro

Supermicro A+ Bedienungsanleitung

Supermicro

Supermicro SuperServer 4027GR-TR Bedienungsanleitung

Supermicro

Supermicro SUPERSERVER 1028TR-T Bedienungsanleitung

Supermicro

Supermicro SUPERSERVER 6028TP-HC1R Bedienungsanleitung

Supermicro

Supermicro SUPERSERVER 6014H-32 Bedienungsanleitung

Supermicro

Supermicro SuperServer SYS-E403-9D-16C-IPD2 Bedienungsanleitung

Supermicro

Supermicro SUPERSERVER 6049GP-TRT Bedienungsanleitung

Supermicro

Supermicro X13SRA-TF Bedienungsanleitung

Supermicro

Supermicro SuperServer E100-12T Bedienungsanleitung

Supermicro

Supermicro SuperServer 5039C-I Bedienungsanleitung

Supermicro

Supermicro SBI-7428R-C3 Bedienungsanleitung

Supermicro

Supermicro SUPERSERVER 6015B-3R Bedienungsanleitung

Supermicro

Supermicro AS-2114GT-DPNR Bedienungsanleitung

Supermicro

Supermicro 2027R-E1R24L Bedienungsanleitung

Supermicro

Supermicro SUPERSERVER 5018A-TN7B Bedienungsanleitung

Supermicro

Supermicro SuperServer 6016T-MT Bedienungsanleitung

Supermicro

Supermicro SuperServer 120C-TN10R Bedienungsanleitung

Beliebte Server Handbücher anderer Marken

HP AlphaServer ES47 Bedienungsanleitung

Dell

Dell PowerEdge R410 Bedienungsanleitung

PowerNAS

PowerNAS CMA Bedienungsanleitung

Supero

Supero FatTwin F617R3-FT Bedienungsanleitung

MSI

MSI P1-109N-L70 Bedienungsanleitung

Dell

Dell PowerEdge XE9640 Handbuch

Dell

Dell PS4100 Montageanleitung

EtroVISION

EtroVISION EV3151 Bedienungsanleitung

NEC

NEC Express5800/T110j Bedienungsanleitung

HP ProLiant Gen9 Bedienungsanleitung

Compaq

Compaq ProLiant 3000 Handbuch

Dell

Dell PowerEdge 3YPMN Bedienungsanleitung

iRobo

iRobo IPC2U Bedienungsanleitung

Nortel

Nortel 1000 Con?guration guide Bedienungsanleitung

Asus

Asus AP7500 Bedienungs- und Wartungshandbuch

Avid Technology

Avid Technology AirSpeed 5000 Bedienungsanleitung

HP Integrity rx2600 Installationsanleitung

Milestone

Milestone Husky IVO 350T Bedienungsanleitung