Swisher ZT18542 Betriebsanleitung
REPAIR MANUAL
ZT18542
ZT2350
Swisher Mower Co
Warrensburg, MO
For additional assistance on service
Contact Swisher Mower Co., Inc.
Phone 1-800-222-8183
Fax 1-660-747-8650
E-mail [email protected]
This manual was produced at the beginning of
our 2006 production. It was specifically
written for those models built after January,
2006. For those models built before that time
refer to the owners manuals for specific parts or
call the Swisher Mower factory for assistance.
For warranty issues or ordering parts for
the engines or the hydro units, contact the
authorized dealer in your area.
TABLE OF CONTENTS
1. If engine won’t crank
2. If engine won’t crank - continued
Battery ground connection at engine
3. Engine cranks but won’t start
Engine stalls when PTO is engaged
4. If PTO clutch will not engage
5. Wiring diagram
Hour meter not operating
6. Wire identification at switches
7. Wire identification on ZT18542
8. Wire identification on ZT2350
9. Carburetor fuel solenoid
10. Battery charging systems
11. Adjusting the drive controls
12. Tracking adjustments
13. Replacement of the hydro unit
14. Repairing or replacing the blade driver
15. Belt replacement routing
IF ENGINE WON’T CRANK
ALWAYS CHECK FUSE FIRST
TEST #1
Using a remote starter switch or a suitable device,
make a connection between the large terminals on
the solenoid. If engine does not crank!!!
•Battery may be weak or dead
•Starter may be bad
•Battery cables may have bad connections
•Do not go to Test #2 until this test gives results
TEST #2
If engine did crank in test #1, disconnect green wire at
spade connector and apply positive voltage from the
battery to the primary wire on the solenoid. Make sure
the one with the eyelet is grounded. If engine doesn’t
crank now, replace the solenoid.Remember, all other
tests are useless unless these two tests make the
engine turn over.
TEST #3
If engine did crank in the first part of test #2, reconnect
green wire to solenoid. Make sure the drive controls are
out in neutral position. Using a jumper wire attached to
the positive terminal of the battery, apply 12 volts to
the red wire on terminal B of the ignition switch. Try to
crank, using the ignition switch. If engine cranks, the
fuse or the fuse holder, or related wiring is defective
somewhere back to the solenoid.
TEST #4
If engine did not crank in test #3, make sure the drive
controls are in neutral position. This time move the
jumper wire attached to the positive terminal of the
battery, to the green wire on S terminal of the ignition
switch. If all components in the circuit are working, the
engine should crank. If it doesn’t, move on to next test.
1
2
A neutral switch is located at the lower end of both
drive control handles and is activated when the handles
are outward in the neutral position. Check that the
plunger buttons on both switches are depressed at least
3/8 inch. Loosening the two mounting screws and
sliding the switch to the side can adjust these.
Ohmmeter should go to zero when checking continuity
across switch terminals with plungers depressed.
With PTO switch in the
off position, meter should
go to zero when checking
continuity across these
two terminals.
If any of the switches in this circuit tested bad, install a
new one and perform Test #4 again. If all switches are
good, a connecting wire must be at fault. Don’t move
past Test #4 until it assures a good circuit. When you do
get good results, hook all wires back to original position
and try the ignition switch again. If no results, you will
need to replace the ignition switch.
This panel is located
right in front of the
battery. It is accessible
by removing the plate
below the front edge of
the seat.
Negative battery ground on ZT2350Negative battery ground on ZT18542
BATTERY GROUND CONNECTION AT ENGINE
ENGINE CRANKS BUT WON’T START
Checks for electrical problems
•While turning ignition switch to its first position, listen for the fuel solenoid on the
carburetor to click. It must click to supply fuel to the carburetor.
•Try a new spark plug.
•Check for spark at plug when it is removed and the threaded end is grounded.
•Unplug the six-position socket that connects engine wiring to mower wiring harness.
Engine will still crank. If plug doesn’t have a spark now, ignition module is probably
defective.
Checks for mechanical problems
•Make sure the tank gas valve is turned on.
•Remove air filter element to check for signs of gas in the throat of the carburetor.
•If no gas, check to see if choke is working properly.
•If all above checks show positive, carburetor must have an internal problem. Remove and
clean the carburetor.
ENGINE STALLS WHEN PTO IS ENGAGED
The seat safety switch plug not being properly inserted, or a
defective plug can cause this problem. If the plug is not
inserted or is defective, the spark plug is grounded out when
the PTO is engage.
To check, remove plug from the PTO switch. Using an
ohmmeter, place one probe on the terminal connected to the
black wire going to the seat safety switch plug. Place the
other probe on a good chassis ground. The meter should be
on zero with no weight on the seat. Pulling the seat down
should open the circuit.
3
IF PTO CLUTCH WILL NOT ENGAGE
Apply a negative ground to this terminal
Apply 12Volts to this terminal. Clutch should
activate, if it doesn’t, clutch is defective.
If clutch checks OK, use a voltmeter to measure for
12 volts at the brown wire’s terminal. First turn
ignition switch to the ON position but don’t start the
engine. Now engage the PTO switch. For the first test
put the negative probe on a good ground, not on the
white wire’s terminal in the plug. If no voltage is
measured, move on to next test.
The problem may be a poor ground on the white wire
in the clutch plug. Check by testing for continuity to
ground or check for voltage between the two
terminals. If no voltage is measured, move on to next
test.
With the PTO switch ON there should be continuity
between these two connectors, if not, replace switch.
If switch tested good, check wires and connectors
back to ignition switch and back to clutch plug.
Used on
ZT2350
Used on
ZT18542
4
WIRING DIAGRAM
HOUR METER USED ONLY ON ZT2350
HOUR METER NOT OPERATING
Hour meter has a positive and a
negative post. Gray wire should go on
the positive. Power is supplied from the
ignition switch.
Green wire from hour meter is
grounded by the oil pressure switch,
therefore only has a ground when the
engine is running.
5
WIRE IDENTIFICATION AT SWITCHES
3623 IGNITION SWITCH
One gray wire goes to the
PTO switch and the other
goes to the hour meter
One black wire goes
to PTO switch and
the other goes to the
engine plug
Green wire goes to PTO switch
Red wire goes to fuse and
on to battery positive at
the solenoid terminal.
One white wire goes to clutch
and other one goes to ground.
STARTER SOLENOID
Heavy red cable
goes to the starter.
Red wire goes through
fuse and onto ignition
switch.
Green wire goes to
neutral switches and
on to the ignition
switch.
Heavy red cable
goes to the
positive post of the
battery.
Red wire goes to
engine plug.
Green wire with
orange stripe goes
to the ground.
PTO SWITCH PLUG
Black wire goes to the
ignition switch.
Green wire goes to the
ignition switch.
Gray wire goes to the
ignition switch.
Black wire goes to the seat
switch.
Green wire goes to the
neutral switches.
Brown wire goes to the
clutch.
6
WIRE IDENTIFICATION ON ZT18542
Gray wire goes to ignition switch
Black wire goes to ignition switch
Red wire goes to terminal on
solenoid with the positive battery
cable
Red wire goes to engine charging
system
Orange wire is not used on this
application
Black wire goes to engine ignition
module
Gray wire goes to carburetor fuel
solenoid
WIRING HARNESS TO ENGINE PLUG CONNECTION
WIRING HARNESS PLUG TO ENGINE
Red wire goes to terminal on solenoid
with the positive battery cable
Black wire goes to the ignition switch
Gray wire to the ignition switch
7
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Swisher Rasenmäher Handbücher
Swisher
Swisher Trim-N-Mow Plus STS67522BS Bedienungsanleitung
Swisher
Swisher ST50022STDQ Bedienungsanleitung
Swisher
Swisher T11544 Bedienungsanleitung
Swisher
Swisher ZT13536, ZT17542B, ZT20050 Bedienungsanleitung
Swisher
Swisher POSTMASTER PST67522 Bedienungsanleitung
Swisher
Swisher Ride King Bedienungsanleitung
Swisher
Swisher The Predator WB11524 Bedienungsanleitung
Swisher
Swisher ZTR2454BS Bedienungsanleitung
Swisher
Swisher T11044, T11544, T10544BSPB, T1 Bedienungsanleitung
Swisher
Swisher Commercial Pro Response Z21554CPHO-CA Bedienungsanleitung
Swisher
Swisher COMMERCIAL PRO Bedienungsanleitung
Swisher
Swisher ST67522CC Bedienungsanleitung
Swisher
Swisher L116-336001 Bedienungsanleitung
Swisher
Swisher T1260F Bedienungsanleitung
Swisher
Swisher FC14560BS Bedienungsanleitung
Swisher
Swisher WB11542F Bedienungsanleitung
Swisher
Swisher ZTR2460BS-CA Bedienungsanleitung
Swisher
Swisher T-40 Bedienungs- und Wartungshandbuch
Swisher
Swisher COMMERCIAL PRO PREDATOR TALON Bedienungsanleitung
Swisher
Swisher ZT18542A Bedienungsanleitung
Beliebte Rasenmäher Handbücher anderer Marken
TALEN TOOLS
TALEN TOOLS AVR HGM30 Bedienungsanleitung
DEWEZE
DEWEZE ATM-725 Bedienungsanleitung
Weed Eater
Weed Eater 180083 Bedienungsanleitung
Husqvarna
Husqvarna Poulan Pro PP185A42 Bedienungsanleitung
Better Outdoor Products
Better Outdoor Products Quick Series Bedienungsanleitung
Cub Cadet
Cub Cadet 23HP Z-Force 60 Betriebsanleitung
