Teeter 600ia Bedienungsanleitung

600ia™

*Inversion Table images may

vary slightly from your model.

Inversion Table Assembly Instructions*

IMPORTANT SAFETY INSTRUCTIONS

READ ALL INSTRUCTIONS BEFORE USING THE INVERSION TABLE.

WARNING

SAVE THESE INSTRUCTIONS

WARNING - To reduce the risk of injury to persons:

• Read and understand all the instructions, view the instructional video, review all other accompanying documents, and inspect the

equipment before using the inversion table. It is your responsibility to familiarize yourself with the proper use of this equipment and the

inherent risks of inversion, such as falling on your head or neck, pinching, entrapment, or equipment failure. It is the responsibility of

the owner to ensure that all users of the product are fully informed about the proper use of the equipment and all safety precautions.

•

Close supervision is necessary when the inversion table is used near children, or by or near invalids or disabled persons.

• Use the inversion table only for its intended use as described in this manual. DO NOT use attachments not recommended by the

manufacturer.

• NEVER drop or insert any object into any opening.

• DO NOT use or store product outdoors.

• DO NOT use if you are over 6 ft 6 in (198 cm) or over 300 lbs. (136 kg). Structural failure could occur or head/neck may impact the

oor during inversion.

• DO NOT allow children to use this machine.

• Keep children, bystanders, and pets away from machine while in use.

• Keep body parts, hair, loose clothing and jewelry clear of all moving parts.

• The inversion table has no user serviceable parts.

• This product is intended for indoor home use only. DO NOT use in any commercial, rental or institutional setting.

FAILURE TO FOLLOW INSTRUCTIONS AND WARNINGS COULD RESULT IN SERIOUS INJURY OR DEATH.

BEFORE YOU BEGIN: Review all steps before beginning assembly and read all precautions before using the inversion table.

Carefully adhere to the Assembly Instructions and Owner’s Manual to help ensure safety and product integrity.

IMPORTANT SAFETY INSTRUCTIONS

READ ALL INSTRUCTIONS BEFORE USING THE INVERSION TABLE.

WARNING

SAVE THESE INSTRUCTIONS

FAILURE TO FOLLOW INSTRUCTIONS AND WARNINGS COULD RESULT IN SERIOUS INJURY OR DEATH.

BEFORE YOU BEGIN: Review all steps before beginning assembly and read all precautions before using the inversion table.

Carefully adhere to the Assembly Instructions and Owner’s Manual to help ensure safety and product integrity.

• DO NOT use the equipment without a licensed physician’s approval and a review of the medical contraindications, as noted in the

Owner’s Manual.

• Failure to assemble and/or use the equipment as directed may void the manufacturer’s warranty on this product and could result in

injury or death.

• Choose a level surface for assembling and operating the table.

• Follow each step in sequence. DO NOT skip ahead.

• Make sure that all fasteners are secure.

• ALWAYS test and inspect the table. Make sure the table rotates smoothly to inverted position and back.

• ALWAYS replace defective components immediately and/or keep the equipment out of use until repair.

Items are not shown to scale. If you have any questions on assembly, contact Customer Service

at 1-800-847-0143 or visit our website at teeter-inversion.com.

Items for Assembly

F5-1050F5-1045 H1-3010

H1-1212

F5-1065

A-Frame

Stability Feet (2)

May come pre-assembled

FitFlexTM Table Bed

Upper Bed Portion

Lower Bed Portion & Frame

Bolts & Nuts (3)

FitFlexTM Bed Frame Extension

Accessories

Head Pillow

Decompression ArchTM

Angle Tether

IA-2500

IA-1101

F1-1300

F1-1300A

F1-1300B

F1-1390

F1-1380

EP-1105

IA-1650

F5-1007

ITEMS FOR ASSEMBLY ITEM NUMBER

Main Shaft

with T-Pin Ankle Lock System

Front Ankle Bar with Foam Rollers

Bolt

Nut

End Cap

IA-1600

F5-1045

H1-1212

H1-3010

F5-1050

ITEMS FOR ASSEMBLY ITEM NUMBER

Handle Assembly

Traction SupportTM Handles (2)

Bolts & Nuts (2)

Bolts/Nuts may come pre-assembled in Handles

Hinge Covers (2)

Allen Bolts (4)

Allen Bolts may come pre-assembled in Hinge Covers

Roller Hinge Assembly

3-Hole Roller Hinges (2)

Tools

10/13mm Wrenches (2)

5mm Allen Wrench

IA-1670

IA-1148B

F1-1250

F5-0071

F5-1065

F5-1088

IA-1149

ITEMS FOR ASSEMBLY ITEM NUMBER

EP-1105 IA-1650 F5-1007

F1-1300B

IA-2500

F1-1300A F1-1390

F1-1380

IA-1101

IA-1670 IA-1148B F1-1250 F5-0071

IA-1600

IA-1149

F5-1088

Other Tools Required for Assembly: Scissors or Snips

*Inversion Table images may vary slightly from your model.

Before reading further, study the drawing below to familiarize yourself with the

important components of your new Teeter Hang Ups®600ia™ Inversion Table.

Before Beginning

Head Pillow

Bed Frame Extension

FitFlex™ Table Bed

3-Hole Roller Hinges

Traction Support™ Handles

Height-Selector Locking Pin

Spreader Arms

Angle Tether

Crossbar

A-Frame

Main Shaft

Ankle Lock System

Ankle Comfort Dial™

Stability Feet

Decompression Arch™

WARNING LABEL PLACEMENT

Important: Please review all labels and supporting materials before using your inversion table.

We hope you enjoy your new Teeter Hang Ups Inversion Table!

If you have any questions, please contact our Customer Service Department at 1.800.847.0143 or www.teeter-inversion.com.

This drawing indicates the locations of the warning

labels found on your product.

If a label is missing, illegible or is removed,

contact Customer Service at the phone number or

website found at the bottom of this page to request a

complimentary replacement label.

Note: Image and labels below not shown actual size.

WARNING - To reduce the risk of personal injury or death:

•

Read and understand all the instructions before using the inversion table.

It is your responsibility to familiarize yourself with the proper use of the

equipment and the inherent risks of inversion, such as falling on your head

or neck, pinching, entrapment or equipment failure.

•

Do not allow children to use the machine.

•

Keep children, bystanders, and pets away from the machine while in use.

•

Keep body parts, hair, loose clothing and jewelry clear of all moving parts.

•

Height/Weight capacity: 4 ft 8 in - 6 ft 6 in (142-198 cm); 300 lbs (136 kgs).

•

This product is for consumer, indoor household use only.

Replace Labels and Owner’s Manual if Damaged, Illegible, or Removed.

Teeter, 9902 162nd St. Ct. E., Puyallup, WA 98375

Toll Free (Phone): 800-847-0143 Web: www.teeter-inversion.com

WARNING

EP-1737 0911-3

WARNING

IA-2007 0611-1

Ankles must be properly

secured before use.

REPLACE LABEL

IF DAMAGED, ILLEGIBLE,

OR REMOVED.

WARNING

E6-1740 0711-0

Do not use Setting A

for users over

220 lbs (100 kgs).

REPLACE LABEL

IF DAMAGED, ILLEGIBLE,

OR REMOVED.

!WARNING

TIPPING HAZARD: For upright storage, leave A-Frame open wide enough

to remain stable, or secure to the wall to prevent tipping. In households with

small children, the table should be stored flat on the floor, not upright.

NX-1720 0910-2

REPLACE LABEL IF DAMAGED, ILLEGIBLE, OR REMOVED.

Step 1

Assemble the Table Bed (F1-1300) and Bed Frame Extension (F1-1380)

NOTE: This assembly will be referred to as Table Bed (F1-1300) for the remainder of

the Assembly Instructions.

• Locate the following items to assemble the FitFlex Table Bed:

Upper Portion (F1-1300A) Lower Portion & Frame (F1-1300B)

Bed Frame Extension (F1-1380) Bolts & Nuts (F1-1390)

5mm Allen Wrench (IA-1149) 10/13mm Wrench (F5-1088)

• Lay the Upper Portion (F1-1300A) face down on the floor.

• Place the Lower Portion & Frame (F1-1300B) face down on top of the Upper Portion and

align the bolt holes (Figure 1).

• Reaching underneath, insert the longest of the three bolts into the Center hole and

hand-tighten with a Nut.

• Reaching underneath, insert one of the shorter bolts through a Top hole in the Upper

Portion and hold in place. Slide one of the Bed Frame Extension loops over the Bolt and

hand-tighten with a Nut (Figure 2).

• Repeat with the remaining side (Figure 3).

• To fully tighten all three nuts to the bolts, insert the 5mm Allen Wrench (IA-1149) into the

Bolt heads and tighten the Nuts using the 10/13mm Wrench (F5-1088).

FIGURE 1

Upper Bolts (2)

Lower Bolt (1)

FIGURE 3

Upper Bolts (2)

FIGURE 2

2Loop

Bolt

Step 2

Assemble the front Stability Feet (IA-1101) onto the A-Frame (IA-2500)

Feet may come pre-assembled.

• Steady both sides of the A-Frame so that the legs will not swing open and turn the A-Frame

so that the base points upwards. This will give you downward leverage to secure the Stability

Feet (Figure 4).

• Determine which is the Right and Left Stability Foot by the imprinted letters “R” and “L”,

found on each foot. You will place each foot on the frame legs so that the letters face inward

towards each other.

• Select the Stability Foot labeled “R” on the inside and insert it on the RIGHT side of the

A-Frame (Figure 4).

• Repeat with the Stability Foot labeled “L” on the LEFT side (Figure 4).

• Open the A-Frame on the floor (Figure 6) and make sure the Spreader Arms are locked

open.

• Familiarize yourself with the Front, Back, Left and Right of the A-Frame. You may want to

refer back to this diagram for reference throughout the assembly process.

Right

Left

FIGURE 4

FIGURE 5

Back

Front

Right Left

FIGURE 6

2Crossbar

Spreader Arms

Step 3

Assemble the 3-Hole Roller Hinges (F5-1065) to the Table Bed (F1-1300)

• For ease-of-assembly, rest the Table Bed against the Crossbar (Figure 7).

• Open the Cam Locks on each side of the Table Bed (Figure 8).

• With the Pivot Pins facing outward, insert the Roller Hinges into the brackets on each side

of the Table Bed Assembly. The Roller Hinges must slide between the Cam Locks and the

Brackets (Figure 8).

• Engage one of the holes in the Roller Hinge over the Bracket Pin. Make sure the Roller

Hinges are in the same hole setting on both sides. Figure 9 shows the Roller Hinges

engaged correctly in Setting C.

• Push down on the Cam Locks (Figure 10) to secure the Roller Hinges.

NOTE: Refer to the Owner’s Manual for an explanation of the hole settings.

If you are unsure, use Setting C to start.

Unlocked Locked

FIGURE 10

FIGURE 9

FIGURE 8

FIGURE 7

2Bracket Pin

Pivot Pin

3Cam Lock

Step 4

Attach the Table Bed (F1-1300) to the A-Frame (IA-2500)

• Pick up the Table Bed, holding each side near the Roller Hinges, and stand in front of the

A-Frame where the Crossbar is located (refer to Figure 6 to determine A-Frame Front).

• Lower each Roller Hinge Pivot Pin into the A-Frame hinge plates, one side at a time

(Figures 11 and 11A).

NOTE: You may need to push outward on the A-Frame in order for the second Pivot Pin

to lock in place.

• Make sure that each Pivot Pin is seated at the base of the slot of the Hinge Plate (Figure 12).

• Ensure that the Self-Locking Hooks have closed over both Pivot Pins, and that the Table

Bed rotates smoothly.

WARNING

Failure of the Self-Locking Hooks to close over both Roller Hinge

Pivot Pins is an indication of improper assembly and if not corrected

could result in serious injury or death!

2Self-Locking Hook

Roller Hinge Pivot Pin

FIGURE 11

FIGURE 11A

FIGURE 12

2Roller Hinge

Self-Locking Hook

Andere Teeter Fitnessgeräte Handbücher

Teeter

Teeter Better Back Comfort Cushion Betriebsanleitung

Teeter

Teeter ComforTrak Series Bedienungsanleitung

Teeter

Teeter FreeStep LT1 Kurzanleitung zur Einrichtung

Teeter

Teeter Power VI-GL Kurzanleitung zur Einrichtung

Teeter

Teeter EP-560 Bedienungsanleitung

Teeter

Teeter FitSpine X2 Bedienungsanleitung

Teeter

Teeter Chin-Up Bedienungsanleitung

Teeter

Teeter FitSpine System Bedienungsanleitung

Teeter

Teeter FitSpine LX4 Bedienungsanleitung

Teeter

Teeter Better Back Betriebsanleitung

Teeter

Teeter L5 Bedienungsanleitung

Teeter

Teeter FitSpine FX-2 Bedienungsanleitung

Teeter

Teeter EP-560 Bedienungsanleitung

Teeter

Teeter FT-1 EP-60 Bedienungsanleitung

Teeter

Teeter FitSpine LX Inversion Table Bedienungsanleitung

Teeter

Teeter FitSpine X1 Bedienungsanleitung

Teeter

Teeter P2 Kurzanleitung zur Einrichtung

Teeter

Teeter Better Back Core Restore Bedienungsanleitung

Teeter

Teeter 900LXTM Bedienungsanleitung

Teeter

Teeter 700ia Bedienungsanleitung

Teeter

Teeter Dex Bedienungsanleitung

Teeter

Teeter DEX II Kurzanleitung zur Einrichtung

Teeter

Teeter FlexTech EP-550 Bedienungsanleitung

Teeter

Teeter FreeStep Betriebsanleitung

Beliebte Fitnessgeräte Handbücher anderer Marken

NSD

NSD PB-188P Bedienungsanleitung

Performance

Performance HyperVibe Bedienungsanleitung

Scalamobil

Scalamobil S27 Bedienungsanleitung

Precor

Precor Experience Series Bedienungsanleitung

FYTTER

FYTTER RedMIUM BENCH BE-T6R Bedienungsanleitung

Taurus

Taurus TF-RK1312 Bedienungsanleitung

Nustep

Nustep T5 Bedienungsanleitung

Precor

Precor CW-507 Bedienungsanleitung

Movement

Movement BICEPS Idea Bedienungsanleitung

Kegel8

Kegel8 V For Men Bedienungsanleitung

Skandika

Skandika Styrke II Bedienungsanleitung

BLK BOX

BLK BOX 21-0122-0B Bedienungsanleitung

Stamina

Stamina aeropilates premier 299 Bedienungsanleitung

SPORTSTECH

SPORTSTECH PBX300 Bedienungsanleitung

ParaBody

ParaBody Serious Steel 877102 Bedienungsanleitung

Weslo

Weslo Gym 650 Bedienungsanleitung

Rebel

Rebel ACTIVE RBA-1011 Bedienungsanleitung

4iiii

4iiii FLiiiight Bedienungsanleitung