Teledyne Lecroy HVD3102 Bedienungsanleitung

Operator's Manual

HVD3102 and HVD3106

High Voltage

Differential Probes

www.GlobalTestSupply.com

Quality Teledyne Lecroy Products Online at: sales@GlobalTestSupply.com

www.GlobalTestSupply.com

Quality Teledyne Lecroy Products Online at: sales@GlobalTestSupply.com

HVD3102 and HVD3106

High-Voltage Differential Probes

Operator's Manual

June 2014

www.GlobalTestSupply.com

Quality Teledyne Lecroy Products Online at: sales@GlobalTestSupply.com

HVD3102 and HVD3106 High-Voltage Differential Probes Operator's Manual

Unauthorized duplication of Teledyne LeCroy documentation materials other than for internal

sales and distribution purposes is strictly prohibited. However, clients are encouraged to

distribute and duplicate Teledyne LeCroy documentation for their own internal educational

purposes.

Teledyne LeCroy is a trademark of Teledyne LeCroy, Inc. Other product or brand names are

trademarks or requested trademarks of their respective holders. Information in this publication

supersedes all earlier versions. Specifications are subject to change without notice.

923278-00

June 2014

www.GlobalTestSupply.com

Quality Teledyne Lecroy Products Online at: sales@GlobalTestSupply.com

Operator's Manual

Contents

Safety 1

Symbols 1

Precautions 1

Introduction 3

Requirements 4

Probe Kit 5

Standard Accessories 6

Voltage Derating for Standard Accessories 8

Specifications 9

Guaranteed Specifications 9

Environmental Characteristics 9

Common Mode Rejection Ratio 12

Input Voltage vs. Frequency and Burn Limit 13

Differential Mode and Common Mode 14

Differential Mode Range and Common Mode Range 14

Differential Input Impedance 14

Operation 15

Connecting to the Test Instrument 15

Connecting to the Test Circuit 15

Operating with an Oscilloscope 16

Maintenance 19

Cleaning 19

Calibration Interval 19

Service Strategy 19

Replacement Parts 19

Returning a Product for Service 20

Functional Test Procedure 21

Required Equipment 21

Test Procedure 21

Performance Verification 22

Required Equipment 22

Preliminary Procedure 23

Certification Procedure 23

923278-00 i

www.GlobalTestSupply.com

Quality Teledyne Lecroy Products Online at: sales@GlobalTestSupply.com

HVD3102 and HVD3106 High-Voltage Differential Probes

HVD3102/HVD3106 Test Record 25

Reference 26

Certifications 26

Warranty 29

Notes 31

ii 923278-00

www.GlobalTestSupply.com

Quality Teledyne Lecroy Products Online at: sales@GlobalTestSupply.com

Operator's Manual

Safety

Follow these instructions to keep the probe operating in a correct and safe condition. Observe

generally accepted safety procedures in addition to the precautions specified in this section. The

overall safety of any system incorporating this product is the responsibility of the

assembler of the system.

Symbols

These symbols appear on the probe or in documentation to alert you to important safety

considerations.

CAUTION of damage to instrument, or WARNING of hazard to health. Attend to the

accompanying information to protect against personal injury or damage. Do not

proceed until conditions are fully understood and met.

HIGH VOLTAGE WARNING. Risk of electric shock.

ESD CAUTION. Risk of electrostatic discharge (ESD) that can damage the instrument if

anti-static measures are not taken.

Double Insulation

Measurement Ground

Precautions

Avoid personal injury or damage to your equipment by complying with the following safety

precautions:

Use only as specified. The probe is intended to be used only with compatible Teledyne LeCroy

instruments. Use of the probe and/or the equipment it is connected to in a manner other than

specified may impair the protection mechanisms.

Do not overload; observe all ratings. To avoid electric shock or fire, do not apply any potential

that exceeds the maximum rating of the probe and/or the probe accessory, whichever is less.

Observe all terminal ratings.

923278-00 1

www.GlobalTestSupply.com

Quality Teledyne Lecroy Products Online at: sales@GlobalTestSupply.com

HVD3102 and HVD3106 High-Voltage Differential Probes

Connect and disconnect properly. Always make the connections from the probe input leads to

the probe accessory that you intend to use before making any connections to a voltage source.

Do not connect accessories to (or disconnect from) a voltage source unless they are first

connected to the probe input leads. Avoid damaging cables through excessive bending.

Use only accessories compatible with the probe. Use only accessories that are rated for the

application. Substituting other accessories (except those specified in this manual) may create a

shock or burn hazard. Ensure the connections between probe input leads and probe

accessories are secure before connecting them to a voltage source.

Comply with the voltage derating curve. When measuring higher frequency signals, comply

with the Voltage vs. Frequency Derating Curve.

Use only within the operational environment listed. Do not use in wet or explosive

atmospheres.

Do not remove the probe's casing. Touching exposed connections may result in electric

shock.

Keep product surfaces clean and dry.

Handle with care. Probe accessory tips are sharp. They can puncture skin or cause other bodily

injury if not handled properly.

Keep fingers behind the finger guard of the probe accessories.

Do not operate with suspected failures. Before each use, inspect the probe and accessories

for any damage such as tears or other defects in the probe body, cable jacket, accessories, etc.

If any part is damaged, cease operation immediately and sequester the probe from inadvertent

use.

2923278-00

www.GlobalTestSupply.com

Quality Teledyne Lecroy Products Online at: sales@GlobalTestSupply.com

Operator's Manual

Introduction

The HVD3102 and 3106 high-voltage active differential probes are safe, easy-to-use, and ideally

suited for power electronics measurements. The probes feature:

lDifferential voltage measurement capability in high common-mode (up to 1000Vrms)

environments.

lExceptional common-mode rejection ratio (CMRR) across a broad frequency range

lWide differential voltage range – 1500Vpeak rated and 2000Vpeak before amplifier

saturation to permit capture of short duration overshoots

lHigh offset capability at both 50x and 500x attenuation settings provides maximum

flexibility for capturing gate drive and control signals floating on a 1000Vdc bus

l1% DC and low frequency gain accuracy

lProBus interface with automatic scaling

lAuto Zero capabilities

The HVD3102 probe (25 MHz, 1000Vrms) and HVD3106 probe (120 MHz, 1000Vrms) are ideal

for power electronics applications, where the reference potential is elevated from ground. Each

probe is supplied with a complete set of lead accessories and a soft accessory case. The main

differences between the two probes is the probe bandwidth (25 MHz vs. 120 MHz).

The CMRR for the probes is exceptional out to very high frequencies. This greatly assists in

measurement of signals in the noisy, high common-mode environments common to power

electronics. The high CMRR combined with low probe noise and high offset capability makes the

probes capable of measuring very small control signals floating on high common-mode

voltages.

Probe specifications are provided for using the probe within a 1500Vpeak differential voltage

range. However, the probe can be safely operated above this range. Up to 2000Vpeak, the probe

will display the signal, but the probe specifications cannot be guaranteed. However, in this

range, the probe is operating below the saturation point of the amplifier, and very reasonable

results can be expected. The V/div range for each probe can be set up to 400V/div (3200Vp-p

displayed over all 8 vertical oscilloscope grid divisions).

923278-00 3

www.GlobalTestSupply.com

Quality Teledyne Lecroy Products Online at: sales@GlobalTestSupply.com

HVD3102 and HVD3106 High-Voltage Differential Probes

The probe is calibrated for high precision measurements to within 1% at DC to low frequency

(~10 kHz). This provides for high accuracy of top and base voltage levels of pulse-width

modulated signals. The AutoZero capability permits further measurement precision by allowing

small offset drifts to be calibrated out of the measurement.

With the ProBus interface, the HVD310x becomes an integral part of the oscilloscope. Power is

provided to the probe through the ProBus interface, so there is no need for a separate power

supply or batteries. Attenuation (50x or 500x) is automatically selected based on oscilloscope

gain range (V/div) setting and the offset adjust is unified with that of the oscilloscope. The

sensitivity of the HVD31xx ranges from 100 mV/Div to 400 V/Div, with the maximum available

offset dependent on the V/div setting and the oscilloscope model. In general, Teledyne LeCroy

12-bit High Resolution Oscilloscopes (HRO) and HD4096 High Definition Oscilloscopes (HDO)

provide the most offset capability over the widest range of V/div settings.

Requirements

The HVD3102 and HVD3106 probes are compatible with any Teledyne LeCroy oscilloscope

equipped with the ProBus interface and XStream software version 7.4 or greater.

4923278-00

www.GlobalTestSupply.com

Quality Teledyne Lecroy Products Online at: sales@GlobalTestSupply.com

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Teledyne Lecroy Messgerät Handbücher

Teledyne Lecroy

Teledyne Lecroy SierraNet M328 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy ADP300 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy Frontline SD Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy PP006D Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy HVFO108 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy ZD500 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy Frontline Sodera LE Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy WaveAce Lab 3 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy WavePulser 40iX Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy RP4030 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy Summit T3-8 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy WaveMaster 8000HD Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy PCI Express 2.0 Mid-Bus Probe Einrichtungshandbuch

Teledyne Lecroy

Teledyne Lecroy PP009 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy Quantumdata 780E Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy HVD3000 Series Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy PP011-2 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy HVD3000 Series Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy PP016 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy Summit T416 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy AP031 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy PP011-1 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy PPE6KV-A Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy HVFO103 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Keysight

Keysight M8290A Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung