Teledyne Lecroy WavePulser 40iX Bedienungsanleitung

WavePulser 40iX

High-speed Interconnect Analyzer

Getting Started Guide

933197-00 Rev A

WavePulser 40iX

Getting Started Guide

Unauthorized duplication of Teledyne LeCroy documentation materials is strictly prohibited. Customers are permitted to

duplicate and distribute Teledyne LeCroy documentation for internal educational purposes only.

WavePulser and Teledyne LeCroy are trademarks of Teledyne LeCroy, Inc. Other product or brand names are trademarks

or requested trademarks of their respective holders. Information in this publication supersedes all earlier versions.

Specifications are subject to change without notice.

933197-00 Rev A,

April, 2021

700 Chestnut Ridge Road

Chestnut Ridge, NY 10977

1.800.5.LECROY •teledynelecroy.com

WavePulser Getting Started Guide 1

Welcome

Thank you for buying a Teledyne LeCroy product. We’re certain you’ll be pleased with the detailed features unique to our instruments. This guide is

intended to help you set up a WavePulser and learn some basic operating procedures, so you're quickly making measurements.

See the WavePulser User Manual for detailed information on the operational features of the WavePulser. The manual installs with the WavePulser software

and can be displayed by selecting Help > Contents from the WavePulser menu bar.

Introduction

Introducing WavePulser 2

WavePulser Approach 3

Set Up

Safety 4

WavePulser Hardware 6

System Set Up 8

Connecting Cables 10

Basics

WavePulser Application Window 12

Basic Configuration 14

Advanced Configuration 16

Viewing TDR/TDT Waveforms 17

Viewing Frequency Domain Results 18

Viewing Time Domain Results 19

Viewing the Smith Chart 20

Calculating Loss (Delta-L) 21

Result Actions 21

Importing S-parameters 22

Exporting S-parameters 23

Saving/Recalling Other Data 23

Working With Result Traces 24

Changing the Display 26

Cursors 26

Measurements and Statistics 27

Math 27

Memories (Reference Waveforms) 28

Pass/Fail Testing 28

Using SI Studio with WavePulser 29

Maintenance

Cleaning 32

Software Updates 32

Service 33

Support 34

Warranty 34

Reference

Touchstone File Format 35

Operational Notes 35

Certifications 36

933197-00 Rev A

Key Specifications

Detailed specifications are on the product datasheet at teledynelecroy.com.

Number of Ports 4

Connector Type 2.92 mm K

Operating Frequency Range DC to 40 GHz

Rise Time 8.5 ps

Frequency Domain Measurements Single-ended and Mixed-mode S-parameters

Time Domain Measurements Impedance Prole, Impulse Response, Step Response, Rho

Calibration Method Internal, automatic SOLT

Key Features

• S-parameters DC to 40 GHz, single- and mixed-mode

• Impedance Profile with <1 mm resolution, differential and common-mode

• Internal, automatic OSLT calibration

• USB-connected, small, lightweight

• Flexible measurement display

• Remove effects from fixtures, connectors and cables

• Emulate eye diagrams with CTLE, DFE and FFE equalization

• Advanced jitter analysis

INTRODUCTION

Introducing WavePulser

WavePulser 40iX is the ideal single measurement tool for high-speed

hardware designers and test engineers. The combination of S-parameters

(frequency domain) and Impedance Profiles (time domain) in a single

acquisition, with a deep toolbox for simulation, emulation, de-embedding

and time-gating, provides unmatched characterization insight.

Designed for High Speed Interconnect Analysis

WavePulser is designed specifically for high-speed interconnect analysis.

It validates, debugs and troubleshoots interconnectivity issues in serial

data cables, channels, connectors, vias, backplanes, printed-circuit

boards, chip and SoC packages. It is simple to set up and use.

Internal, Automatic Calibration

WavePulser calibration standards are built-in (included in the standard

unit) and calibration is always automated, simple and fast—make one

connection to the DUT and press Go. WavePulser does not require

the purchase of additional, external calibration standards. In fact,

WavePulser's TDR/TDT-based approach is independent of setup, making

calibration less likely.

Full-range DC to 40 GHz

WavePulser provides results to DC and extending to 40 GHz of bandwidth,

so TDR step response and time-gated and/or emulated physical layer

signal responses can avoid extrapolations for low-frequency and DC

response—ideal for interconnect systems.

WavePulser Getting Started Guide 3

WavePulser Approach

WavePulser uses time domain reflectometry to characterize a DUT’s elec-

trical behavior by stimulating the DUT with impulses and measuring reflec-

tion and transmission. Once a measurement is configured, all phases

proceed without any user intervention whatsoever. This is accomplished

using an internal switch matrix assembly that routes pulses to internally

connected standards and to the front panel ports. After acquiring calibrat-

ed measurements of the DUT, post-processing calculations are performed

such as de-embedding, time-gating, etc. The post-processing calculations

can even be reconfigured and new results calculated without the need for

new measurement acquisitions.

SOLT Calibration Phase

In the calibration phase, pulses are routed to internal short, open, load,

and thru standards while measurements are made of these standards.

The measurements are processed along with measurements made at the

factory to provide an internal self-calibration at the instrument ports.

TDR/TDT Measurement Phase

In the DUT measurement phase, pulses are routed out to the DUT through

the front panel bulkhead connector and cables. Multiple acquisitions are

taken with the DUT pulsed at each port.

S-parameter Calculation Phase

On the host PC, the WavePulser application uses algorithms to apply the

calibration to the DUT measurements and to de-embed the instrument

cables to provide calibrated DUT measurements at the DUT ports. In this

phase, any further processing is performed, such as fixture and adapter

de-embedding, time-gating and physicality enforcements.

INTRODUCTION

Pulser/

Sampler

Pulser/

Sampler

Pulser/

Sampler

DUT

CABLES

ADAPTORS

Internal Calibration Reference Plane

De-embedded Measurement Reference Plane

Optional Manual Calibration Reference Plane

Measurement Reference Plane

FIXTURE

ABLE

WAVEPULSER PORTS

Switch System & Internal Standards

Pulser/

Sampler

933197-00 Rev A

Power and Ground

Use only the Power button to power down. Do not power down by

switching off a connected battery/power strip or pulling the AC line cord

from the outlet while the instrument is turned on.

CAUTION. In "Standby Power" mode the instrument is still

connected to the AC supply. The only way to fully power down the

instrument is to physically disconnect the power cord from the AC

outlet. We recommend unplugging the instrument if it will remain

unused for a long period of time

Use only the power cord shipped with the instrument and certified for

the country of use.

The instrument is provided with a 10A/250V 18AWG rated grounded cord

set containing a molded three-terminal polarized plug and a specific

IEC-60320 (Type C13) connector for making line voltage and safety

ground connections.

Maintain ground. The AC inlet ground is connected to the frame of the

instrument. For adequate protection against shock, connect line cords

only to outlets with safety ground contacts.

WARNING. Interrupting the protective conductor inside or outside

the WavePulser, or disconnecting the safety ground terminal,

creates a hazardous situation. Intentional interruption is prohibited.

Operating Environment

Use indoors only.

Use only within the operational environment listed. Do not use in wet or

explosive environments.

Temperature 5 °C to 40 °C

Humidity Maximum RH 80% (non-condensing) up to 30 °C

decreasing linearly to RH 50% at 40 °C

Altitude Up to 10,000 ft (3,048 m) at or below 30 °C

Safety

To maintain the instrument in a correct and safe condition, observe gener-

ally accepted safety practices in addition to the precautions specified here.

CAUTION of potential damage

to equipment, or WARNING of

potential bodily injury. Refer to

manual. Do not proceed until the

information is fully understood

and conditions are met.

WARNING. Risk of electric shock

or burn.

Electrostatic Discharge Warning.

Frame or chassis terminal

Alternating current

Power On/Standby Power

Symbols

AC Power 100-240 VAC (±10%) at 50/60/400 Hz (±5%)

Automatic AC Voltage Selection

Consumption

Maximum Operating 40 W / 40 VA

Standby 2 W / 2 VA

SET UP

WavePulser Getting Started Guide 5

SET UP

ESD Precautions

CAUTION. The WavePulser is sensitive to damage by Electrostatic

Discharge. Always wear the supplied grounding wrist strap and

take standard ESD precautions when using the WavePulser.

Connect the strap to the ground terminal on the front of the WavePulser.

CAUTION. Cables are capacitors. Always park the relays (p.11) and

discharge the center conductor of the WavePulser cables to

ground before connecting them to the WavePulser unit or the DUT.

Failure to do so may result in electrical damage to the pulser/

samplers that is not warrantable. Do not connect or disconnect

cables during measurements or TDR/TDT acquisitions when the

relays are engaged.

General Precautions

Connect and disconnect cables properly. Turn only the nut on the cable

connector to tighten/loosen cables, do not rotate the pins.

Do not remove the covers or inside parts. Refer all maintenance to

qualified service personnel.

Use only as intended by manufacturer.

Do not operate with suspected failures. Check the unit and cables

regularly. If any part is damaged, or you suspect the protections haved

been impaired, cease operation immediately and secure the instrument

from inadvertent use.

Cleaning

Keep product surfaces clean and dry. Follow instructions on p.32.

Cooling

The instrument relies on forced air cooling with an internal fan and

ventilation openings. An internal fan control circuit regulates the fan speed

based on the ambient temperature. This is performed automatically after

start-up with no manual intervention required.

Care must be taken to avoid restricting the airflow around the openings at

the side and rear of the instrument.

Do not block the cooling vents. Leave a minimum four-inch gap

(10 cm) between the instrument and the nearest object. Do not

allow foreign matter to enter through the vents.

Calibration

The recommended factory calibration interval is one year. Calibration

should be performed by qualified personnel only. See p.33 for instructions

on returning the instrument to Teledyne LeCroy Service.

Center Conductor

(discharge to ground)

Shield

933197-00 Rev A

A. Power On/Standby Power Button

B. Port 1 - Port 4 Connectors

C. Ground Terminal

D. USBTMC Port

E. AC Power Inlet

WavePulser Hardware

SET UP

Front View Rear View

WavePulser Getting Started Guide 7

The WavePulser ships with high-phase stability cables that are calibrated

and serialized to the WavePulser unit, along with the S-parameter les for

de-embedding each cable.

Cables

The cables utilize 2.92 mm K connectors.

The connector head on the end of the cable to be connected to the

WavePulser has a colored band matching the color of the port to which it

is calibrated. Always be sure to connect the cable to the matching port so

that the proper S-parameter le is used to de-embed the cable. See p.10.

We recommend leaving the cables attached once connected to the

WavePulser; there is no need to remove them when not in use.

CAUTION. Cap exposed cable connectors with the supplied end

caps to keep them clean when not in use.

SET UP

SI Kit (Optional)

The SI Kit is delivered with the WavePulser-40iX-Bundle or may be

purchased as an optional accessory. This option enables the Signal Integrity

Studio (SI Studio) tools within the WavePulser application.

The SI Kit also includes:

• USB license key for standalone use when disconnected from WavePulser

• Multi wrench

• 4 female-female cable adapters

• OSLT Cal Kit for performing the User 2nd-tier Calibration procedure

• Torque wrench

933197-00 Rev A

Install WavePulser Software

1. Visit teledynelecroy.com/support/softwaredownload and click the

link to WavePulser Downloads > WavePulser Software.

2. Enter the required model information and account login to download

the installer for your operating system. If you don’t yet have an

account, create one now.

3. On the host PC, unzip the installer and double-click

WavePulserInstallerxx.exe to launch the WavePulser Setup Wizard.

4. Follow the wizard prompts. We recommend taking the full installation.

At minimum, you will need the WavePulser application and the drivers.

5. When installation is complete, reboot.

6. Follow with the initialization procedure.

CAUTION. The installation may take several minutes and appear to

stop at points. Do not power down the host at any point during the

installation process. Do not connect the WavePulser to the host

prior to software installation.

SET UP

System Set Up

The WavePulser system consists of the WavePulser unit, cables and

application host computer.

Fully assembled WavePulser system connected to DUT

Host System Requirements

The WavePulser application host PC must meet the following requirements:

• x64 Windows

10 Pro operating system

• 2.4 GHz or higher processor

• 4 GB or more RAM

• 2 GB or more free HDD space for the installed application

• Minimum 1280x780 pixel display, 1920x1080 recommended

• Minimum USB 2.0 high-speed port, USB 3.0 recommended

Inhaltsverzeichnis

Andere Teledyne Lecroy Messgerät Handbücher

Teledyne Lecroy

Teledyne Lecroy 980 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy PPE6KV-A Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy MDA810 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy 980 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy HVD3000 Series Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy Everywhereyoulook DL02-HCM Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy WaveAce Lab 3 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy PP011-1 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy Everywhereyoulook SierraNet M168 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy PCI Express 2.0 Mid-Bus Probe Einrichtungshandbuch

Teledyne Lecroy

Teledyne Lecroy HVFO103 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy Frontline Sodera LE Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy HVD3102 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy AP031 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy LabMaster LM 10-25Zi-A Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy PCI Express 5.0 U.2 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy Summit T416 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy Summit T3-8 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy USB Advisor T3 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy Quantumdata 780E Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy HVFO108 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy AP033 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy RP2060 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy M42de Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Keysight

Keysight M8290A Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung