Teledyne T3LCR1002 Bedienungsanleitung

T3LCR1002, T3LCR1100, T3LCR1300

Precision LCR Meters

Quick Start Guide

This quick start guide contains proprietary information, which is

protected by copyright. All rights are reserved. No part of this manual

may be photocopied, reproduced or translated to another language

without prior written consent of Teledyne LeCroy company.

The information in this quick start guide was correct at the time of

printing. However, Teledyne LeCroy continues to improve products

and reserves the rights to change specification, equipment, and

maintenance procedures at any time without notice.

SAFETY INSTRUCTIONS

Safety Symbols

These safety symbols may appear in the quick start guide or on the

instrument.

WARNING

Warning: Identifies conditions or practices that

could result in injury or loss of life.

CAUTION

Caution: Identifies conditions or practices that

could result in damage to the instrument or to

other properties.

When you notice any of the unusual conditions listed below,

immediately terminate operation and disconnect the power cable.

Please contact the Teledyne service center representative for repair

of the instrument. If you continue to operate without repairing the

instrument, there is a potential fire or shock hazard for operators.

The instrument is operating abnormally if:

•The instrument emits abnormal noise, smell, smoke, or a spark-

like light during the operation.

•The instrument generates high temperature or electrical shock

during operation.

•The power cable, plug, or receptacle on the instrument is

damaged.

•Foreign substances or liquid has fallen into the instrument.

The following general safety precautions must be observed during

all phases of operation, service, and repair of this instrument.

Failure to comply with these precautions or with specific

WARNINGS elsewhere in this manual may impair the protection

provided by the equipment. In addition it violates safety standards

of design, manufacture, and intended use of the instrument.

Disclaimer

Teledyne assumes no liability for the customer's

failure to comply with these requirements.

Ground The

Instrument

To avoid electric shock hazards, the instrument

chassis and cabinet must be connected to a safety

earth ground by the supplied power cable with

earth blade.

DO NOT Operate

In An Explosive

Atmosphere

Do not operate the instrument in the presence of

inflammable gasses or fumes. Operation of any

electrical instrument in such an environment

constitutes a definite safety hazard.

Keep Away From

Live Circuits

Operating personnel must not remove instrument

covers. Component replacement and internal

adjustments must be made by qualified

maintenance personnel. Do not replace

components with the power cable connected.

Under certain conditions, dangerous voltages may

exist even with the power cable is removed. To

avoid injuries, always disconnect the power and

discharge the circuits before touching them.

DO NOT Service

Or Adjust Alone

Do not attempt internal service or adjustment

unless another person, capable of rendering first

aid and resuscitation, is present.

DO NOT

Substitute Parts

Or Modify

Instrument

Because of the danger of introducing additional

hazards, do not install substitute parts or perform

unauthorized modifications to the instrument.

Return the instrument to a Teledyne authorized

service center for service and repair to ensure that

safety features are maintained.

GETTING STARTED

This chapter describes names and functions of the front panel, rear

panel, and screen display and provides the basic procedures for

operating the T3LCR series.

Overview

The Teledyne T3LCR series is a general-purpose LCR meter for

incoming inspection of components, quality control, and laboratory

use.

The T3LCR series is used for evaluating LCR components,

materials, and semiconductor devices over a wide range of

frequencies (10 Hz to 300 kHz) and test signal levels (10.00mV to

2.00V & 100.0uA to 20.00mA).

With its built-in comparator, the T3LCR series can output

comparison/decision results for sorting components into a

maximum of ten bins. Furthermore, by using the handler interface,

the T3LCR

Main Features

Correction

Function

•OPEN/SHORT correction

Eliminates measurement errors due to stray

parasitic impedance in the test fixtures.

Comparator

Function

(Sorting)

•Bin sort

The primary parameter can be sorted into

BIN1- BIN9, AUX, OUT and HI/IN/LO for

each of the primary measurement parameters.

The sequential mode or tolerance mode can be

selected as the sorting mode.

series can be easily combined with a component handler,

and a system controller to fully automate component testing,

sorting, and quality- control data processing.

The list Meas function permits entry of up to 10 frequencies or test

signal levels points to be automatically measured.

•Limit Setup

Absolute value, deviation value, and %

deviation value can be used for setup.

•BIN count

Countable from 0 to 999999

Files

•Up to 10 setup conditions can be written

to/read from the built-in non-volatile memory.

Key Lock

•The front panel keys can be locked.

RS-232

•Complies with SCPI.

Front Panel















 

 

Description

1. LCD Display

2. Soft-key

3. Number Key

4. Cursor Key

5. Power Switch

6. Measure key

7. Setup Key

8. BNC Terminal

9. Trigger Key

10. ESC Key

11. USB Disk Port (USB-Host)

12. System Soft-key

Rear Panel

Power

Press the power key for at least 2 seconds. Release power key when

the POWER LED is lit.

Power Off

Press the power key at least 2 seconds. LCR down when you

release the power key.

Description

1. Power Cable Receptacle(Outlet)

2. Frame Terminal

3. USB Interface (Type B)

4. RS-232 Interface

5. Handler Interface







Warm-up Time

T3LCR series is ready to be used as soon as the power-up sequence

has completed. However, to achieve the specification accuracy, first

warm up the instrument for 30 minutes.

Connect to the Device Under Test (DUT)

The T3LCR series uses a four terminal measurement configuration

that provides easy, accurate and stable measurements and avoids

mutual inductance, interference from measurement signals, noise

and other factors inherent with other types of connections.

Connect to DUT

WARNING

L Force L Sense H Sense H Force

-DUT+

Identifies conditions or practices that could result

in injury or loss of life. Do not apply DC voltage or

current to the UNKNOWN terminals. Applying a

DC voltage or current may lead to device failure.

Connect the measurement sample (DUT) to the

test port (or the test fixture, cables, etc. after the

DUT has been completely discharged.

SPECIFICATIONS

The following are the basic specifications for the T3LCR series. For

detailed specifications, please see the user manual

General Specification

Display

RGB color TFT-LCD, Size: 3.5” (320x240)

Test Function

Cs-Rs, Cs-D, Cp-Rp, Cp-D, Lp-Rp, Lp-Q, Ls-Rs,

Ls-Q, Rs-Q, Rp-Q, R-X, DCR, Z-θr, Z-θd, Z-D, Z-Q

Monitor

Parameter

Z, D, Q, Vac, Iac, Δ, Δ%, θr, θd, R, X, G, B, Y

(2 Parameter)

40 times/s, 10 times/s, 3 times/s

Test Frequency

T3LCR1300: 10Hz-300kHz

T3LCR1100: 10Hz-100kHz

T3LCR1002: 10Hz-2kHz

Frequency range and resolution

Frequency range(F)

Resolution

10.00Hz ≤F ≤99.99Hz

0.01Hz

100.0Hz ≤F ≤999.9Hz

0.1Hz

1.000Hz ≤F ≤9.999Hz

1Hz

10.00kHz ≤F ≤99.99kHz

10Hz

100.0kHz ≤F ≤300.0kHz

100Hz

Frequency Accuracy

Frequency range(F) ±0.01% 4 digit resolution

Display Range

Parameter

Resolution

0.00001uH-9999.99H

0.00001pF-9999.99mF

R, X, |Z|

0.00001Ω-99.9999MΩ

G, B, |Y|

0.01nS-999.999S

0.00001-9.99999

0.00001-99999.9

θd

-179.999°-179.999°

θr

-3.14159-3.14159

DCR

0.00001Ω-99.9999MΩ

-999999%-999999%

AC Test signal level

10.00mV-2.00V (±10%)

CV: 10.00mV-2.00V (±6%)

100.0uA-20.00mA (±10%)

CC: 100.0uA-20.00mA(±6%) (@2VMax)

DCR Test signal level

+2V, 0.066A(Max.), Output impedance fixed

30Ω

DC Bias: Internal

±2.5V (0.5%+0.005V)

List Test

10Step (Frequency/Voltage/Current)

Output impedance

30Ω, 50Ω and 100Ω

Ranging

Auto, Hold and Nominal range.

Total 9 Ranges.

Equivalent Circuit

Serial and Parallel

OPEN/SHORT Test

OPEN/SHORT Zeroing (ALL,SPOT)

Files

built-in 10 files and USB Disk 10 files, 9999 Log

File, 999 Picture File, 10000 Data (.csv)

Beep Feature

OFF/PASS/FAIL

Trigger Mode

Internal, Manual, External and Bus Trigger.

Andere Handbücher für T3LCR1002

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Teledyne Messgerät Handbücher

Teledyne

Teledyne 4250 Betriebsanleitung

Teledyne

Teledyne T3MIL50 Bedienungsanleitung

Teledyne

Teledyne Kibra DDR Bedienungsanleitung

Teledyne

Teledyne HVD3102 Bedienungsanleitung

Teledyne

Teledyne 402R-EU Bedienungsanleitung

Teledyne

Teledyne 2010B Bedienungsanleitung

Teledyne

Teledyne CP Series Bedienungsanleitung

Teledyne

Teledyne HVG-2020A Bedienungsanleitung

Teledyne

Teledyne 9070 Bedienungsanleitung

Teledyne

Teledyne WIRELESS GROUNDLINK WQAR Bedienungsanleitung

Teledyne

Teledyne T200 Bedienungsanleitung

Teledyne

Teledyne BENTHOS UDB-9000 Bedienungsanleitung

Teledyne

Teledyne Echotrac E20 Bedienungsanleitung

Teledyne

Teledyne ADFM Pro20 Betriebsanleitung

Teledyne

Teledyne HASTINGS Everywhereyoulook 200 Series Bedienungsanleitung

Teledyne

Teledyne HASTINGS Everywhereyoulook 201 Series Bedienungsanleitung

Teledyne

Teledyne 3000TA Installations- und Benutzerhandbuch

Teledyne

Teledyne Everywhereyoulook T3PM1100 Bedienungsanleitung

Teledyne

Teledyne AX300 Bedienungsanleitung

Teledyne

Teledyne GMI PS200 Bedienungsanleitung

Teledyne

Teledyne 200A Bedienungsanleitung

Teledyne

Teledyne 3350 Bedienungsanleitung

Teledyne

Teledyne HASTINGS 2002 Bedienungsanleitung

Teledyne

Teledyne 514 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Keysight

Keysight M8290A Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung