Tennsco ZL7 Series Bedienungsanleitung

PK-1920919

ASSEMBLY INSTRUCTIONS & PARTS MANUAL

RETAIN INSTRUCTIONS FOR FUTURE REFERENCERETAIN INSTRUCTIONS FOR FUTURE REFERENCE

Tennsco LLC., Dickson, TN 37056-1888 • (866) 446-8686

GENERAL SAFETY INFORMATIONGENERAL SAFETY INFORMATION

Some parts may have sharp edges. CARE must be taken when handling various pieces to avoid injury.

For safety, wear a pair of work gloves when assembling or performing any maintenance on units.

LIMITED WARRANTYLIMITED WARRANTY

Tennsco warrants goods purchased hereunder to be free of defects in materials and workmanship for a period of one (1) year from the date of shipment, hereunder. This warranty shall not apply in

the event goods are damaged as a result of misuse, abuse, neglect, accident, improper application, modication or repair by persons not authorized by Seller, where goods are damaged during

shipment, or where the date stamps on the goods have been defaced, modied or removed. UNLESS CONSIDERED UNENFORCEABLE OR UNLAWFUL UNDER APPLICABLE LAW:

a. ALL IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO WARRANTIES OR MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY EXCLUDED:

b. BUYERS REMEDY, IF ANY, FOR ANY DEFECTIVE GOODS SHALL BE LIMITED TO A REFUND BY SELLER OR REPLACEMENT OF THE GOODS AT SELLER’S OPTION, AND SHALL IN NO

EVENT INCLUDE DAMAGES OF ANY KIND, WHETHER INCIDENTAL, CONSEQUENTIAL OR OTHERWISE.

NO GOODS ACCEPTED FOR RETURN WITHOUT PRIOR APPROVAL. Seller shall have the right to inspect any goods claimed to be defective at Buyers place of business or require Buyer to return the

goods to Seller for inspection on Seller’s premises. Transportation charges covering returned goods will be borne by Seller only if such goods are proven to be defective, are covered by this warranty

and are returned within the warranty period stated above.

Z-Line Long Span Shelving

ZL7-Series

ASSEMBLY OF LONG SPAN SHELVING

Tools Needed: A rubber mallet for seating the shelf supports into the uprights.

Two people are recommended for assembly. Approximate assembly time: 20-30 minutes per section.

2. Depending upon whether you ordered a single unit or an

adder unit, you may have one or both of the styles of upright

shown. A single unit will use SUR posts for all four uprights,

as show below in Figure A. If you plan on installing an adder

unit, you should build your starter unit with two ZTP posts

on one end which will join with the adder as shown in Figure B.

1. The reference numbers used throughout this sheet refer to

the illustration on the back cover. This is to help you to

identify the various parts as they are mentioned.

3. With the help from an associate, or using a wall for support,

connect two SUR uprights (Ref. No. 1) using two front-to-

back supports (Ref. No. 3), one at the top and one near the

bottom (leaving the bottom-most keyhole slot empty). Be

sure the front-to-back supports are fully seated in the

keyhole slots as shown.

5. With the help of an associate, connect the two unit ends

with left-to-right shelf supports (Ref. No. 4). These should

be placed with the ange up and at matching levels

with the front-to-back supports, creating a at surface

on which to

place decking.

SUR

NOTE: Inset is shown from the opposite side (below).

ZTP

Figure A

Figure B

IMPORTANT: All shelf supports

must be installed with the ange

facing up, as shown on right.This

ange is what the shelves will

rest on.

NOTE: If you are planning to install an adder unit, this

second set of uprights should consist of ZTP uprights

(Ref. No. 2) to act as an intermediate assembly.

Carefully review step 2 to better understand.

⁭⁭

NOTE:

Every fourth

keyhole slot

is shaped

differently

(with a

attened top)

for easier

alignment of

supports.

⁭⁭

4. Place a third front-to-back support in the middle slots of

the two uprights (at the level you want your third shelf to

be). This forms one end of the shelving unit. Repeat steps 3

and 4 to construct a

second set of

unit ends.

⁭⁭

9. If joining more than one unit together, your original unit

should have been assembled with ZTP uprights on one end,

as described in step 4. Simply continue adding shelf supports

and uprights to complete your additional units.

8. If particle board decking (Ref. No. 6) or wire decking (Ref.

No. 7) was ordered, place the decking on each shelving level.

The decking should t ush inside the shelf supports. If you

have purchased a single unit, your shelving unit is now

complete. For adder units, see step 9.

7. Attach the shelf reinforcements (Ref. No. 5) at each level by

sliding them onto the rivets until centered. Tap down on the

reinforcements until they are seated rmly.

⁭⁭

6. Attach the remaining shelf supports at the desired shelf

levels, making sure that all shelf supports are completely

seated in the upright slots.

⁭⁭

NOTE: If you have purchased additional shelf levels, the

shelf supports for the extra levels may also be inserted

at this time.

NOTE: Recommended

number of reinforements

per shelf are as follows:

48”w = 1 reinforcement

60”w = 1 reinforcement

72”w = 2 reinforcement

96”w = 3 reinforcements

⁭⁭

REPLACEMENT PARTSREPLACEMENT PARTS

Left-to-RightLeft-to-Right

Shelf SupportShelf Support

(Ref No. 4)(Ref No. 4)

⁭⁭

NOTE: Additional hardware may be included for replacement purposes.NOTE: Additional hardware may be included for replacement purposes.

Tennsco makes every effort to ensure that all units ship complete with all parts and arrive undamaged.Tennsco makes every effort to ensure that all units ship complete with all parts and arrive undamaged.

However, should your unit contain missing or damaged parts, please contact your purchase location.However, should your unit contain missing or damaged parts, please contact your purchase location.

49B19249B192

⁭⁭

ZTPZTP

UprightUpright

(Ref No. 2)(Ref No. 2)

Front-to-BackFront-to-Back

End SupportEnd Support

(Ref No. 3)(Ref No. 3)

Particleboard DeckingParticleboard Decking

(Ref No. 6)(Ref No. 6)

SUR UprightSUR Upright

(Ref No. 1)(Ref No. 1)

Front-to-Back ShelfFront-to-Back Shelf

Deck SupportDeck Support

(Ref No. 5)(Ref No. 5)

Wire DeckingWire Decking

(Ref No. 7)(Ref No. 7)

DESCRIPTIONDESCRIPTION QTY.QTY.

REF.REF.

NO.NO. PART NO.**PART NO.**

High Capacity Post (single or starter units only)

“T” Post (adder units only)

Front-to-Back Shelf Support

24” to 30” Shelf Depth

36” to 48” Shelf Depth

Left-to-Right Shelf Support

Front-to-Back Shelf Deck Support

48” to 60” Shelf Width

72” Shelf Width

96” Shelf Width

Optional Particleboard Decking

Optional Wiring Decking

SUR-84

ZTP-84

LRA-dd

LRA-ddG

LRA-ww

SDS-dd

PB-wwdd

ZWD-wwdd

**Where the sufx “ww” or “dd” is used in the part number, the width (ww) or depth (dd) is substituted in the part **Where the sufx “ww” or “dd” is used in the part number, the width (ww) or depth (dd) is substituted in the part

number. For example, for a 72” wide shelf support, the part number would be LRA-72.number. For example, for a 72” wide shelf support, the part number would be LRA-72.

Quantites apply to the basic 3-shelf unit only. If you have ordered additional shelf levels, quantities will vary accordingly. Quantites apply to the basic 3-shelf unit only. If you have ordered additional shelf levels, quantities will vary accordingly.

⁭⁭

Andere Tennsco Inneneinrichtung Handbücher