Tews Technologies TPCE280 Bedienungsanleitung

The Embedded I/O Company

TPCE280

PCI Express x8, Gen3 XMC Carrier

Version 1.0

User Manual

Issue 1.0.3

January 2022

TEWS TECHNOLOGIES GmbH

Am Bahnhof 7 25469 Halstenbek, Germany

Phone: +49 (0) 4101 4058 0 Fax: +49 (0) 4101 4058 19

e-mail: [email protected] www.tews.com

TPCE280 User Manual Issue 1.0.3 Page 2 of 20

TPCE280-10R

PCI Express x8 Carrier for one XMC module, +12V

Power Supply from PCIe Connector, 12V VPWR, J14

I/O, J16 I/O, JTAG connections to XMC module via

14-pin header

TPCE280-11R

PCI Express x8 Carrier for one XMC module, +12V

Power Supply from PCIe Connector, 5V VPWR, J14

I/O, J16 I/O, JTAG connections to XMC module via

14-pin header

TPCE280-20R

PCI Express x8 Carrier for one XMC module, +12V

power supply from external PCIe graphics power

connector used, 12V VPWR, J14 I/O, J16 I/O, JTAG

connections to XMC module via 14-pin header

TPCE280-21R

PCI Express x8 Carrier for one XMC module, +12V

power supply from external PCIe graphics power

connector used, 5V VPWR, J14 I/O, J16 I/O, JTAG

connections to XMC module via 14-pin header

This document contains information, which is

proprietary to TEWS TECHNOLOGIES GmbH. Any

reproduction without written permission is forbidden.

TEWS TECHNOLOGIES GmbH has made any

effort to ensure that this manual is accurate and

complete. However TEWS TECHNOLOGIES GmbH

reserves the right to change the product described

in this document at any time without notice.

TEWS TECHNOLOGIES GmbH is not liable for any

damage arising out of the application or use of the

device described herein.

Style Conventions

Hexadecimal characters are specified with prefix 0x,

i.e. 0x029E (that means hexadecimal value 029E).

For signals on hardware products, an ‚Active Low’ is

represented by the signal name with # following, i.e.

IP_RESET#.

Access terms are described as:

W Write Only

R Read Only

R/W Read/Write

R/C Read/Clear

R/S Read/Set

2022 by TEWS TECHNOLOGIES GmbH

All trademarks mentioned are property of their respective owners.

TPCE280 User Manual Issue 1.0.3 Page 3 of 20

Issue Description Date

1.0.0 Initial Issue December 2018

1.0.1 Added 3D model figures to show the positions of the JTAG

rotary switch and the LEDs

March 2018

1.0.2 Corrected the J15 pinout table to x8 pinout, was x4 September 2020

1.0.3 Order Options -2xR: removed the PCIe VGA power connector

adapter cable

January 2022

TPCE280 User Manual Issue 1.0.3 Page 4 of 20

Table of Contents

1 PRODUCT DESCRIPTION ........................................................................................... 6

2 TECHNICAL SPECIFICATION ..................................................................................... 7

3 HANDLING AND OPERATING INSTRUCTIONS ......................................................... 8

ESD Protection ................................................................................................................................8

Installation of TPCE280-2xR ..........................................................................................................8

4 XMC INTERFACE ......................................................................................................... 9

Power ...............................................................................................................................................9

4.1.1 VPWR Tolerance ......................................................................................................................9

4.1.2 Power Limits for XMC Modules ................................................................................................9

4.1.3 Stable Power Supply ..............................................................................................................10

Installation of an XMC Module.....................................................................................................10

5 JTAG ........................................................................................................................... 11

USB Type C Connector ................................................................................................................11

JTAG voltage for XMC Module ....................................................................................................11

6 INDICATORS .............................................................................................................. 12

LED Indicators...............................................................................................................................12

7 PIN ASSIGNMENTS ................................................................................................... 13

XMC J15 .........................................................................................................................................13

XMC J16 I/O Connector ................................................................................................................14

7.2.1 X5 – Firefly Micro Flyover Connector #1 ................................................................................14

7.2.2 X6 – Firefly Micro Flyover Connector #2 ................................................................................16

XMC J14 I/O Connector ................................................................................................................18

X8 - 14-Pin JTAG Header ..............................................................................................................19

X3 – PCIe VGA Graphics Power Connector ...............................................................................20

TPCE280 User Manual Issue 1.0.3 Page 5 of 20

List of Figures

FIGURE 1-1 : TPCE280 BLOCK DIAGRAM .....................................................................................................6

FIGURE 5-1 : JTAG VOLTAGE ROTARY SELECTOR SWITCH LOCATION, MARKED RED (TOP VIEW

OF TPCE280) ...........................................................................................................................................11

FIGURE 6-1 : ON-BOARD LED PLACEMENT ...............................................................................................12

List of Tables

TABLE 2-1 : TECHNICAL SPECIFICATION.....................................................................................................7

TABLE 4-1 : CURRENT LIMITS FOR THE XMC MODULES...........................................................................9

TABLE 5-1 : ROTARY SELECTOR SWITCH CONFIGURATION..................................................................11

TABLE 6-1 : ON-BOARD LED DESCRIPTION...............................................................................................12

TABLE 7-1 : XMC J15 PIN ASSIGNMENT .....................................................................................................13

TABLE 7-2 : PIN ASSIGNMENT X5 UEC5 .....................................................................................................14

TABLE 7-3 : PIN ASSIGNMENT X5 UCC8.....................................................................................................15

TABLE 7-4 : PIN ASSIGNMENT X6 UEC5 .....................................................................................................16

TABLE 7-5 : PIN ASSIGNMENT X6 UCC8.....................................................................................................17

TABLE 7-6 : X4 - J14 I/O PIN ASSIGNMENT.................................................................................................18

TABLE 7-7 : X5 – 14-PIN JTAG HEADER PIN ASSIGNMENT ......................................................................19

TABLE 7-8 : X3 – 6-PIN AUXILLIARY POWER CONNECTOR .....................................................................20

TPCE280 User Manual Issue 1.0.3 Page 6 of 20

1 Product Description

The TPCE280 is a standard height, half length PCI Express Revision 3.0 compatible module that provides

one slot for a single-width XMC module used to build modular, flexible and cost effective I/O solutions for all

kinds of applications like process control, medical systems, telecommunication and traffic control.

The PCI Express x8 link from the host board to the XMC module is enhanced by a PCIe Gen3 Redriver,

allowing safe operation of XMC modules on PCIe mainboards.

The voltage level for the XMC’s main power supply, VPWR, is selectable via order option. The TPCE280-

x0R variants provide 12V VPWR and the TPCE280-x1R order options provide 5V VPWR.

The TPCE280 supports XMC front panel I/O, and also P14 and P16 rear I/O independently.

XMC P14 Rear-I/O is offered through an 68-pin ERNI SMC, right angle male, 1.27mm pitch connector. The

I/O lines are routed differential.

XMC P16 Rear-I/O is implemented through two Samtec Firefly UCC8 and UEC5 connectors providing

access to the P16 I/O lines.

The TPCE280 provides a fan mounted under the XMC slot that helps cooling the system. This fan does not

occupy a second PCIe slot as most other carrier solutions do.

The PCIe edge card connector provides +12V and +3.3V. The TPCE280-1xR uses only the +12V of the

PCIe edge card connector to generate all power supply voltages for the XMC slot (+3.3V, VPWR and +12V).

According to the PCIe specification, a PCIe x8 card is allowed to use 25W on its +12V supply which allows to

operate most of the available XMC modules on the TPCE280-1xR. For XMC modules with increased power

requirements, the TPCE280-2xR offer a PCIe Graphics Power Connector to supply XMCs with up to 75W.

A 14-pin 2mm JTAG header is available for XMC module debugging purposes. All five JTAG signals are

routed directly to the XMC slot.

J16

PCIe

A01

F19

A01

F19

J14

J15

ERNI - 154766

x8 PCIe ReDriver

2 4

Fire-Fly

TPCE280-x0R:

TPCE280-x1R:

VPWR = 12V

VPWR = 5V

VPWR

PCIe x8

J14 I/O

J16 I/O

JTAG

Figure 1-1 : TPCE280 Block Diagram

TPCE280 User Manual Issue 1.0.3 Page 7 of 20

2 Technical Specification

Mechanical and Electrical Interfaces

PCI Express PCI Express x8, Revision 3.0

Standard Height

Half-Length

XMC Slot ANSI/VITA 42.0-2008 (R2014)

ANSI/VITA 42.3-2006 (R2014)

Single-Width

XMC Interface

Number of XMC Slots 1

XMC I/O Access XMC Front Panel I/O

XMC P14 Rear-I/O through 68-pin ERNI SMC, right angle male,

1.27mm pitch connector

XMC P16 Rear-I/O through two Samtec SAMTEC UCC8 and

UEC5 connectors

Maximum Current for Rear I/O Lines is 0.5A!

On-Board Devices

PCI Express ReDriver 2x DS80PCI810 (Texas Instruments)

Physical Data

Power Requirements - @ +3.3V DC

180mA maximum @ +12V DC

Additional power is required by the XMC Module!

Power Stable for XMC Slot The power supply for the XMC slot is stable approximately 5ms

after the system power supply is stable.

Maximum Power for XMC Slot The maximum power available for an XMC module is variant

dependent. Please see chapter “Power Limits for XMC Modules”

for detailed information.

Temperature Range Operating

Storage

-40°C to +85°C

MTBF TPCE280: 344000h

MTBF values shown are based on calculation according to MIL-HDBK-217F and

MIL-HDBK-217F Notice 2; Environment: GB20°C.

The MTBF calculation is based on component FIT rates provided by the

component suppliers. If FIT rates are not available, MIL-HDBK-217F and

MIL-HDBK-217F Notice 2 formulas are used for FIT rate calculation.

Humidity 5 – 95 % non-condensing

Weight TPCE280: 98 g

Table 2-1 : Technical Specification

TPCE280 User Manual Issue 1.0.3 Page 8 of 20

3 Handling and Operating Instructions

ESD Protection

The TPCE280 is sensitive to static electricity. Packing, unpacking

and all other handling of the TPCE280 has to be done in an ESD/EOS

protected Area.

Installation of TPCE280-2xR

For the TPCE280-2xR variants, it is imperative to always connect a

PCI Express VGA power connector to the TPCE280, even if no XMC

is mounted.

TPCE280 User Manual Issue 1.0.3 Page 9 of 20

4 XMC Interface

Power

The TPCE280 can provide the following power supplies to the XMC:

VPWR (12V or 5V)

3.3V

+12V (optional XMC voltage, but always supplied by the TPCE280)

-12V (optional XMC voltage, available via order option)

As the ±12V supplies are optional and VPWR can be 12V or 5V, it depends on the TPCE280 order option

which supplies are available and what voltage level is provided as VPWR.

4.1.1 VPWR Tolerance

For all TPCE280 variants with VPWR = 12V, this voltage is directly connected to the 12V supply from the

system (either via PCIe edge connector or the PCIe VGA Graphics connector). The PCIe specification allows

for tolerances of ±8%, whereas the XMC specification allows only for ±5%.

This has to be taken into consideration when using these TPCE280 variants.

4.1.2 Power Limits for XMC Modules

The following current limits have to be taken into account when choosing the appropriate TPCE280 for the

power requirements of the XMC module.

TPCE280 Voltage Current Limits *)

TPCE280-1xR

3.3V 3 A

VPWR 12V (TPCE280-10R) 2.1 A

5V (TPCE280-11R) 5 A

+12V 0.2 A

-12V 0.2 A

TPCE280-2xR

3.3V 8 A

VPWR 12V (TPCE280-20R) 6.25 A

5V (TPCE280-21R) 8 A

+12V 0.2 A

-12V 0.2 A

Table 4-1 : Current Limits for the XMC Modules

*) System dependent: After power-up, the PCI-Express specification limits the total power

consumption of x8 PCIe Add-In Cards to 25W. If more power is needed, the XMC can request it

from the system via mechanisms defined in the PCI-Express specification.

Alternatively, a TPCE280 variant with PCIe Graphics Power Connector could be used.

In principle, an XMC could draw more than 100W. Since most XMCs tend to convert the delivered power into

heat, users should keep in mind that it needs appropriate system cooling solutions when such high power

XMCs are used.

TPCE280 User Manual Issue 1.0.3 Page 10 of 20

4.1.3 Stable Power Supply

All power supplies for the XMC slot are stable max. 5ms after the system power supply is stable.

Installation of an XMC Module

The XMC module has to be mounted on the TPCE280 prior to installation into the system.

Before installing an XMC module, be sure that the power supply for the TPCE280 is turned off.

TPCE280 and XMC are Electrostatic Sensitive Devices (ESD). Use an anti-static mat connected

to a wristband when handling or installing the components.

If the XMC has a front panel, first remove the cover from the XMC front panel cut-out of the TPCE280. Install

the XMC at an angle so that the XMC front panel pushes through the XMC front panel cut-out. Then rotate

down to mate with the XMC connectors on the TPCE280. If the XMC has no front panel, simply plug in the

XMC, and leave the cover in the XMC front panel cut-out of the TPCE280.

After the XMC module has been installed, it can be secured on the TPCE280 using the mounting screws that

come with the XMC module. There are four screw mounting locations, two at the XMC front panel and two at

the standoffs near the XMC bus connectors.

According to the XMC specification, VPWR can be 5V or 12V, and it is up to the XMC to deal with both

power supply voltage levels.

Nevertheless, there are some XMCs on the market that work only with VPWR = 5V, sometimes with

remarkable and non-reversible effects when they are powered with VPRW = 12V.

For those XMCs, a special TPCE280 variant with VPWR = 5V is available. Always check if your XMC

supports the VPWR voltage of the TPCE280 variant used.

For all TPCE280 with VPWR = 12V, this voltage is directly connected to the 12V supply from the PCIe

connector. The PCIe specification allows for tolerances of ±8%, whereas the XMC specification allows only

for ±5%. This has to be taken into consideration when using these TPCE280 variants.

Inhaltsverzeichnis

Andere Tews Technologies PCI-Karte Handbücher

Tews Technologies

Tews Technologies TCP201 Bedienungsanleitung

Beliebte PCI-Karte Handbücher anderer Marken

ERMA

ERMA SSI 1417 Bedienungsanleitung

SIIG

SIIG CyberSerial Dual PCI Montageanleitung

I-Bus

I-Bus IBC2602 Bedienungsanleitung

Exsys

Exsys EX-60102 Bedienungsanleitung

Chelsio Communications

Chelsio Communications T5 Series Bedienungsanleitung

Conrad Electronic

Conrad Electronic 97 46 71 Bedienungsanleitung

Micro Innovations

Micro Innovations USB650A Bedienungsanleitung

KTI Networks

KTI Networks KF-310 Bedienungsanleitung

Asus

Asus SpaceLink WL230 Bedienungsanleitung

SIIG

SIIG SC2475 Bedienungsanleitung

TRENDnet

TRENDnet TEW-703PI Bedienungsanleitung

Belkin

Belkin F5D7000F Bedienungsanleitung

Pericom

Pericom PI7C7100 Bedienungsanleitung

ADLINK Technology

ADLINK Technology cPCI-3548 Bedienungsanleitung

Digium

Digium TE200 Series Bedienungsanleitung

Allo.com

Allo.com 2nd Gen E1/T1/J1 Bedienungsanleitung

Western Digital

Western Digital FireWire PCI Adapter Bedienungsanleitung

Pyle

Pyle Gamelink PLINK1 Bedienungsanleitung