Toshiba IK-4KE Bedienungsanleitung

CAMERA CONTROL UNIT

IK-4KE

INSTRUCTION MANUAL

U.S.A INFORMATION

NOTE:This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part

15 of the FCC Rules.These limits are designed to provide reasonable protection against harmful interference when the

equipment is operated in a commercial environment.This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to

radio communications.Operation of this equipment in a residential area is likely to cause harmful interference in which

case the user will be required to correct the interference at his own expense.

USER-INSTALLER CAUTION:Your authority to operate this FCC veriﬁed equipment could be voided if

you make changes or modiﬁcations not expressly approved by the party responsible for compliance to

Part 15 of the FCC Rules.

This manual is made from recycled paper.

For Customer Use

Enter below the Serial No.

which is located on the

bottom of the cabinet. Retain

this information for future ref-

erence.

Model No.: IK-4KE

Serial No.:

Following information is only for EU-member states:

In residential areas this product may cause radio interference, therefore this product must not be used

in residential areas.

The use of the symbol indicates that this product may not be treated as household waste.

By ensuring this product is disposed of correctly, you will help prevent potential negative

consequences for the environment and human health, which could otherwise be caused by

inappropriate waste handling of this product. For more detailed information about the take-

back and recycling of this product, please contact your supplier where you purchased the

product or consult.

cev.fr

Protection of Personal Information

Images taken by the camera that reveal the likeness of an individual person may be considered

personal information. To disclose, exhibit or transmit those images over the internet or otherwise,

consent from such individual person may be required.You are solely responsible to obtain such

consent.

Limitation of Usage

The product is not designed for any “critical applications.” “Critical applications” means life support

systems, exhaust or smoke extraction applications, medical applications, commercial aviation,

mass transit applications, military applications, homeland security applications, nuclear facilities or

systems or any other applications where product failure could lead to injury to persons or loss of life

or catastrophic property damages. Accordingly, Toshiba disclaims any and all liability arising out of

the use of the product in any critical applications.

TABLE OF CONTENTS

1. CAUTIONS ON USE AND INSTALLATION...............................................................................................6

2. COMPONENTS..........................................................................................................................................6

3. ITEMS CONTROLLED BYTHE SCREEN DISPLAY.................................................................................7

4. NAMES AND FUNCTIONS........................................................................................................................9

5. CONNECTION..........................................................................................................................................10

5. 1 Standard Connection.......................................................................................................................10

5.1.1 4K mode................................................................................................................................10

5.1.2 1080 i/p mode.......................................................................................................................11

5. 2 Cautions on Connection...................................................................................................................11

5. 3 Connector Pin Assignments.............................................................................................................12

6. OPERATION.............................................................................................................................................13

6. 1 Automatic Black Balance .................................................................................................................13

6. 2 White Balance..................................................................................................................................13

6. 3 Scene File........................................................................................................................................15

6. 4 Gain .................................................................................................................................................15

6. 5 Shading Correction..........................................................................................................................16

6. 6 Switching of Video Signal Output.....................................................................................................17

6. 7 Freeze operation..............................................................................................................................17

7. MODE SETTING BY ON SCREEN DISPLAY..........................................................................................18

7. 1 Using the Menus..............................................................................................................................18

7. 2 Menus..............................................................................................................................................19

( 1 ) SHUTTER (Electronic shutter).........................................................................................................19

(1. 1) Changing the setting in AUTO mode.....................................................................................20

(1. 2) Changing the setting in MANUAL mode................................................................................22

(1. 3) Changing the setting in SS (Synchro. Scan) mode................................................................22

( 2 ) GAIN (Video gain)............................................................................................................................23

(2. 1) Changing the setting in AUTO (AGC: Automatic gain control) mode.....................................23

(2. 2) Changing gain in MANUAL mode..........................................................................................23

( 3 ) WHT BAL (White balance)...............................................................................................................24

(3. 1) Changing the setting in AWB (Automatic White Balance) mode ...........................................24

(3. 2) Changing gain in MANUAL mode..........................................................................................25

( 4 ) PROCESS1.....................................................................................................................................26

(4. 1) Changing gamma correction ON/OFF...................................................................................26

(4. 2) Changing gamma correction level .........................................................................................26

(4. 3) Changing black gamma correction level................................................................................27

(4. 4) Changing the knee correction point.......................................................................................27

(4. 5) Changing the knee correction slope......................................................................................27

(4. 6) Changing pedestal.................................................................................................................28

(4. 7) Change of white clip ..............................................................................................................28

( 5 ) PROCESS2.....................................................................................................................................29

(5. 1) Changing detail (outline) gain................................................................................................29

(5. 2) Change of detail boost frequency..........................................................................................29

(5. 3) Change of horizontal and vertical detail balance...................................................................29

( 6 ) PROCESS3.....................................................................................................................................30

(6. 1) Changing matrix color correction ON/OFF ...........................................................................30

(6. 2) Selection of color for correction.............................................................................................30

(6. 3) Changing HUE and GAIN of selected color...........................................................................30

(6. 4) Changing the total Chroma gain (simultaneously for all colors in the matrix)........................30

( 7 ) SYNC...............................................................................................................................................31

(7. 1) INT screen.............................................................................................................................31

(7. 2) Changing EXT. setting ...........................................................................................................31

( 8 ) OPTION...........................................................................................................................................32

(8. 1) Changing shading correction mode.......................................................................................32

(8. 2) Changing manual shading correction mode..........................................................................32

(8. 3) Changing detail signal output ................................................................................................32

(8. 4) Change of vertical inversion setting.......................................................................................33

(8. 5) Change of horizontal inversion setting...................................................................................33

(8. 6) Switching of inversion mode display......................................................................................33

(8. 7) Changing the freeze display ..................................................................................................33

(8. 8) Changing 4K OSD (On Screen Display) output.....................................................................34

(8. 9) Changing the output mode ....................................................................................................34

(8. 10) Changing RS-232C baud rate .............................................................................................34

( 9 ) Setting USER area ..........................................................................................................................35

( 10 ) Returning to factory settings..........................................................................................................36

7. 3 External Sync...................................................................................................................................36

( 1 ) External sync signal input conditions...............................................................................................36

( 2 ) External sync frequency range........................................................................................................36

( 3 ) Using the unit with external sync signal...........................................................................................36

7. 4 Synchro. Scan Operation.................................................................................................................36

( 1 ) Setting by 1H...................................................................................................................................36

8. BEFORE MAKING SERVICE CALL........................................................................................................37

9. SPECIFICATIONS....................................................................................................................................38

10. EXTERNAL APPEARANCE DIAGRAM................................................................................................39

2. COMPONENTS

(1) Camera Control Unit......................................................................................................................1

(2) Accessories

(a) Instruction manual .................................................................................................................. 1

1. CAUTIONS ON USE AND INSTALLATION

•Handlingtheunit.

Do not drop, jolt, or vibrate, as this may result in

damage to the unit and may cause problems.Treat the

camera cables carefully to prevent cable problems,

such as breaks in the cable and loose connections.

•Installthecamerainalocationfreefromnoise.

If the camera or the cables are located near power

utility lines or aTV, etc. undesirable noise may appear

on the screen. In such a case, try to change the

location of the camera or the cable wiring.

•Operatingambienttemperatureandhumidity.

Do not use the camera in places where temperature

and humidity exceed the speciﬁcations.Picture quality

will deteriorate and internal parts may be damaged.

Be particularly careful when using in places exposed

to direct sunlight.When shooting in hot environments,

depending on the conditions of the object and the

camera (for example when the gain is increased),

noise in the form of vertical strips or white dots may

occur.This is not a malfunction.

•Whennotusingthecameraforextendedperiods

of time.

Switch the control unit off and disconnect the power

supply.

•Avoidusingorstoringthecamerainthefollowing

places:

Places ﬁlled with highly ﬂammable and corrosive gas.

Places near gasoline, benzene, or paint thinner.

Places subject to strong vibration.

Places containing chemicals (such as pesticides),

rubber or vinyl products for extended periods of time.

•Thisproductisforindooruseonly.

The following descriptions are for a camera head “IK-

4KH” connected to this camera control unit.

•Donotshootintenselight.

If a strong light is imaged, vertical stripes or traverse

bands may appear on the screen but this is not a

failure.

•Moire

A moire pattern is an interference pattern generated

when two repetitive line patterns overlap.This is not a

malfunction.Eliminating the repetitive line patterns, or

aligning the two patterns, will eliminate the moire.

•Handlingofthecameraheadandprotectioncap.

Keep the camera head and protection cap away

from children as they may pose a choking hazard.

The protection cap protects the image sensing plane

when the lens is removed from the camera head, do

not discard the protection cap.

•Whencleaningthecamera.

Unplug the power source before cleaning. Clean

with a soft dry cloth only. Do not use chemicals or

chemically treated cloths. Chemicals may damage

coatings and printed letters. When cleaning the lens,

use lens cleaning paper.

•Installationwithoutatripod.

Before installing the camera head, make sure that the

location can withstand the total weight of the camera

head.

If this is not the case, reinforce the area to prevent the

unit from dropping, which may result in damage to the

unit or personal injury.

3. ITEMS CONTROLLED BYTHE SCREEN DISPLAY

Item Available selections Preset value

(Factory setting)

Electronic shutter

MODE AUTO, MANUAL, SS MANUAL

AUTO level -100 – 0 – 100 0

AUTO exposure metering PEAK/AVE, MEDIAN PEAK/AVE

AUTO peak/average 00 : 10 – 10 : 00 00 : 10

AUTO response speed 1 – 10 – 20 10

AUTO area

PRESET A, PRESET B, PRESET C, PRESET D, PRESET E,

USER (USER area is possible to set in 64 zones)

PRESET A

Maximum AUTO shutter

speed

1/200s, 1/250s, 1/300s, 1/350s, 1/400s, 1/450s, 1/500s,

1/550s, 1/600s, 1/700s, 1/800s, 1/900s, 1/1000s,

1/1200s, 1/1500s, 1/2000s, 1/4000s, OFF OFF

MANUAL shutter speed OFF, 1/100s, 1/125s, 1/250s, 1/500s, 1/1000s, 1/2000s,

1/3000s, 1/4000s, 1/5000s, 1/10000s OFF

Syncro. scan 1/1125H – 1124/1125H, OFF OFF

Gain

MODE AUTO, MANUAL, OFF OFF

AUTO maximum gain 0dB to 24dB 24dB

AUTO minimum gain -6dB to 0dB -6dB

MANUAL gain -6dB to 24dB 0dB

White balance

MODE AWB, MANUAL AWB

Color temperature 3200K, 5600K 3200K

AWB R PAINT -10 – 0 – 10 0

AWB B PAINT -10 – 0 – 10 0

AWB area

PRESET A, PRESET B, PRESET C, PRESET D, PRESET E,

USER (USER area is possible to set in 64 zones)

PRESET A

MANUAL R GAIN -100 – 0 – 100 0

MANUAL B GAIN -100 – 0 – 100 0

Gamma correction ON, OFF ON

Gamma correction level -10 – 0 – 10 0

Black gamma correction level LOW, NORMAL, HIGH NORMAL

Knee correction point 70%, 75%, 80%, 85%, 90%, 95%, 100% 85%

Knee correction slope 1 – 8 – 16 8

Master pedestal -200 – 0 – 200 0

Red pedestal -100 – 0 – 100 0

Blue pedestal -100 – 0 – 100 0

White clip 100% − 109% 109%

Detail gain 0 − 10 − 31 10

Detail boost frequency 1 − 10 − 16 16 (4K mode)

10 (1080p mode)

(1080i mode)

HV balance 8/16 − 16/16 − 24/16 (ratio of V/H) 16/16

Matrix

Correction ON/OFF ON, OFF ON

Selection of correction color R, R-Ye,Ye,Ye-G, G, G-Cy, Cy, Cy-B, B, B-Mg, Mg, Mg-R R

Phase -15 – 0 – 15 0

Gain -15 – 0 – 15 0

Chroma gain

-31 − 0 − 31 0

Ext. Sync

H phase adjustment

-650 – 0 – 650 0

Shading correction mode SET, MANUAL, OFF OFF

Manual shading correction -128 – 0 – 127 0

Detail signal output ON, OFF OFF

Vertical inversion ON, OFF OFF

Horizontal inversion ON, OFF OFF

Inversion mode display switch ON, OFF OFF

Item Available selections Preset value

(Factory setting)

Changing the FREEZE display ON, OFF ON

4K OSD output A, B, C, D A

Output mode 4K, 1080p, 1080i 4K

RS-232C baud rate 9600bps, 19200bps 9600bps

4. NAMES AND FUNCTIONS

DC IN 12V

REMOTE

3G/HD-SDI

A B C D

SYNC IN/OUT

OFF

59.94

OUT

FORMAT SYNCKEY LOCK

1 2 3 4 5

87 96

[Front]

[Rear]

Camera cable

for “IK-4KH”

terminal

POWER switch

POWER LED

FILE button

FREEZE button

DISP button

PAGE button

MENU UP

(SHD) button

MENU DOWN

button

DATA UP

(AWB) button

DATA DOWN

(ABB) button

FREEZE

SYNC switch

⑬

REMOTE terminal

KEY LOCK switch

3G/HD-SDI A, B, C, D

terminal

DC IN 12V terminal

FORMAT switch

SYNC IN/OUT terminal

Camera cable for “IK-4KH”

terminal Where the camera cable for “IK-4KH” is connected.

POWER LED Illuminates to indicate the unit is powered on.

POWER switch Turns power on or off.

FILE button To switch the scene ﬁles.

FREEZE button To freeze the display.

DISP button Changes the display mode.

PAGE button To switch and select menus.

MENU UP (SHD) button To select the function to be conﬁrmed or changed on the menu.

(Also used when performing auto shading correction.)

MENU DOWN button To select the function to be conﬁrmed or changed on the menu.

DATA UP (AWB) button To change the value of the function selected by the MENU (UP/DOWN) button.

(Also used when performing an AWB.)

DATA DOWN (ABB) button To change the value of the function selected by the MENU (UP/DOWN) button.

(Also used when performing an ABB.)

DC IN 12V terminal Accepts a DC power input (12V).

REMOTE terminal To connect to a RS-232C device for remote control function.

SYNC IN/OUT terminal Used when the camera output signal is synchronized to an external signal or

when a synchronized signal is output.(BNC connector)

3G/HD-SDI A, B, C, D terminal Image signal output terminal for 3G/HD-SDI formats. (BNC connector)

KEY LOCK switch Enables/disables buttons

FORMAT switch Switches between 59.94Hz and 50Hz.

SYNC switch Switches between input and output of synchronized signals from

SYNC IN/OUT terminals in

5. CONNECTION

5. 1 Standard Connection

5. 1. 1 In case output mode is 4K

DC power supply

(option)

Lens

(commercial

product)

Camera

Head

Control unit

Camera Cable

for IK-4KE

（option）

4K monitor

3G-SDI × 4 TV input

(commercial product)

DC IN 12V

3G/HD-SDI

x 4

IK-4KE

IK-4KH

(option)

Coaxial cable × 4, 75

(commercial

product)

* 3G/HD-SDI A, B, C, D terminals and screen positioning are shown below.

レンズ

（市販品）

IK-4KH

（別売品）

カメラコントロールカメラ

ヘッドユニット

専用カメラ

ケーブル

（別売品）

4Kモニターテレビ

3G-SDI×4入力対応

（市販品）

DC電源（別売品）

DCIN12V

3G-SDI×4

Upperleft Upperright

Lowerleft Lowerright

IK-4KE

DC IN 12V

REMOTE

3G/HD-SDI

A B C D

SYNC IN/OUT

OFF

59.94

OUT

FORMAT SYNCKEY LOCK

1 2 3 4 5

87 96

5. 1. 2 In case output mode is 1080p or 1080i

DC power supply

(option)

Lens

(commercial

product) Camera

Camera

Head

Control unit

Camera Cable

for IK-4KE

(option)

SDI monitor

3G/HD-SDI TV

(commercial product)

DC IN 12V

3G/HD-SDI

Coaxial cable, 75Ω

(commercial

product)

IK-4KE

IK-4KH

(option)

* 3G/HD-SDI A, B, C, D terminalsoutput the same signal.

5. 2 Cautions on Connection

• When connecting the camera cables, be sure to turn off the camera control unit and any other equipment

connected to it.

• For DC power supply connecting to DC IN 12V terminal, use class II DC power supply approved according

to EN60950-1 in Europe. or use UL listed and/or CSA approved ungrounded type AC adaptor with the

speciﬁcations described below in U.S.A.or Canada.

Power supply voltage : 12V DC ±10%

Current rating : More than 1.5A

Ripple voltage :Less than 50 mV (p–p)

Connector : HR10A–7P–4S by HIROSE electronics Co.Ltd

Pins 1, 2 : +12V

Pins 3, 4 : GND

• If the securing screw on the connector of the camera cable loosens, noise may appear on the screen. Be sure

to tighten the connector completely.

• Only use the specic optional camera heads with this camera controller.

The use of any other camera heads may cause damage to the control unit and camera head.

• The video signal output of this camera control unit has no function for automatically selecting output according

to the monitor TV. Therefore, be sure to switch the output mode of this camera control unit according to the

monitor as no image will be displayed on the monitor if the camera output mode and the monitor input mode

do not match. For switching, refer to the item 6.6 “Switching of Video Signal Output”.

• SDI interface

The SDI (serial digital interface) is a high-speed serial interface standard used mainly in commercial video

equipment. This unit supports both HD-SDI and 3G-SDI.

When image output is “4K” or “1080p”, 3G-SDI output is used. When image output is “1080i”, HD-SDI output

is used.

Use a 3G/HD-SDI compatible cable to connect to the 3G/HD-SDI terminal.

Note:

The image may not appear on the monitor's screen immediately, depending on the conditions and the type of

monitor.

5. 3 Connector Pin Assignments

The rear panel of the camera control unit has the following connectors:

DC IN 12V; REMOTE; SYNC IN/OUT and 3G/HD-SDI A, B, C, D terminals. Use the appropriate cables to connect

with these connectors.

DC IN 12V

REMOTE

3G/HD-SDI

A B C D

SYNC IN/OUT

OFF

59.94

OUT

FORMAT SYNCKEY LOCK

1 2 3 4 5

87 96

DC IN 12V terminal REMOTE terminal

1 +12V 1 -

2 +12V 2 TXD

3 GND 3RXD

4 GND 4 -

5GND

6 -

7 -

8 -

9 -

Inhaltsverzeichnis

Andere Toshiba Steuereinheit Handbücher

Toshiba

Toshiba IK-TF7U Bedienungsanleitung

Toshiba

Toshiba TC-net 100 Bedienungsanleitung

Toshiba

Toshiba nv Series Bedienungsanleitung

Toshiba

Toshiba MMW-UP0271LQ-E Bedienungsanleitung

Toshiba

Toshiba IK-CU43A Bedienungsanleitung

Toshiba

Toshiba BMS-SM1280HTLE Bedienungsanleitung

Toshiba

Toshiba nv Series Bedienungsanleitung

Toshiba

Toshiba LTD121EA43G Bedienungsanleitung

Toshiba

Toshiba B-EX206-QM-R Bedienungsanleitung

Toshiba

Toshiba RBM-A101VAE Bedienungsanleitung

Toshiba

Toshiba G3 Plus Pack Bedienungsanleitung

Toshiba

Toshiba GN-4030-A3 Bedienungsanleitung

Toshiba

Toshiba V Series Bedienungsanleitung

Toshiba

Toshiba IK-CU44A Bedienungsanleitung

Toshiba

Toshiba TOSVERT VF-AS1 Series Bedienungsanleitung

Toshiba

Toshiba nv Series Bedienungsanleitung

Toshiba

Toshiba Adjustable Speed Drive H7 Series Bedienungsanleitung

Toshiba

Toshiba B-EX906-FF-QM-R Bedienungsanleitung

Toshiba

Toshiba IK-TF5U Bedienungsanleitung

Toshiba

Toshiba B-8204-QM-R Bedienungsanleitung

Toshiba

Toshiba HX7 Series Bedienungsanleitung

Toshiba

Toshiba IK-HD3D Bedienungsanleitung

Toshiba

Toshiba LONWORKS LIU007Z Bedienungsanleitung

Toshiba

Toshiba MD911 Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung