Toshiba MR-2018 Bedienungsanleitung

SERVICE MANUAL

AUTOMATIC DOCUMENT FEEDER

PAPER FEED UNIT

MR-2018/2019

MY-1034

Model: MR-2018/MR-2019/MY-1034

Publish Date: July 2008

File No. SME08000300

R080621G0600-TTEC

Ver00_2008-07

Trademarks

•Microsoft

®, Windows®, Windows®98, Windows®Me, Windows®2000, Windows®XP, Windows®

Vista, and Internet Explorer®are registered trademarks or trademarks of Microsoft Corporation in

the U.S.A. and other countries.

• Adobe®, the Adobe®logo, Acrobat®, the Adobe®PDF logo, and ReaderTM are registered trade-

marks or trademarks of Adobe Systems Incorporated in the United States and other countries.

• IBM, PC/AT, and PowerPC are trademarks of International Business Machines Corporation.

• All other trademarks and copyrights are the property of their respective owners.

Under the copyright laws, this manual cannot be reproduced in any form without prior written permission

of TOSHIBA TEC CORPORATION. No patent liability is assumed, however, with respect to the use of the

information contained herein.

General Precautions for Installation/Servicing/Maintenance

for the MR-2018/2019 and MY-1034

The installation and service should be done by a qualified service

technician.

1. When installing the MR-2018/2019 and MY-1034 to the Equipment, be sure to follow the instructions

described in the "Unpacking/Set-Up Procedure for the MR-2018/2019 and MY-1034" booklet which

comes with each unit of the MR-2018/2019 and MY-1034.

2. The MR-2016/3017 should be installed by an authorized/qualified person.

3. Before starting installation, servicing or maintenance work, be sure to turn OFF and unplug the

equipment first.

4. When servicing or maintaining the MR-2018/2019 and MY-1034, be careful about the rotating or

operation sections such as gears, pulleys, sprockets, cams, belts, etc.

5. When parts are disassembled, reassembly is basically the reverse of disassembly unless otherwise

noted in this manual or other related materials. Be careful not to reassemble small parts such as

screws, washers, pins, E-rings, toothed washers to the wrong places.

6. Basically, the machine should not be operated with any parts removed or disassembled.

7. Delicate parts for preventing safety hazard problems (such as switches, sensors, etc. if any) should

be handled/installed/adjusted correctly.

8. Use suitable measuring instruments and tools.

9. During servicing or maintenance work, be sure to check the serial No. plate and other cautionary

labels (if any) to see if they are clean and firmly fixed. If not, take appropriate actions.

10.The PC board must be stored in an anti-electrostatic bag and handled carefully using a wristband,

because the ICs on it may be damaged due to static electricity. Before using the wrist band, pull out

the power cord plug of the equipment and make sure that there is no uninsulated charged objects in

the vicinity.

11.For the recovery and disposal of used MR-2018/2019 and MY-1034, consumable parts and packing

materials, follow the relevant local regulations or rules.

12.After completing installation, servicing and maintenance of the MR-2018/2019 and MY-1034, return

the MR-2018/2019 and MY-1034 to its original state, and check operation.

MR-2019/2018/MY-1034 GENERAL 1 - 1

[1] GENERAL

1. List of available options

: Option available

: Option not available

2. Outline and specifications of each option

A. MR-2019 (Reversing Automatic Document Feeder)

The reversing automatic document feeder (RADF) holds up to 50

originals for automatic feeding.

Part names

Specifications

[Conditions] Speed with tray 1, normal size, paper size of A4 (8.5" x

11"), and RADF.

*1: Indicates the speed from 1st to 30th sheet (i.e., 60th surface).

B. MR-2018 (Automatic Document Feeder)

The automatic document feeder (ADF) holds up to 50 originals for

automatic feeding.

Part names

Specifications

Model

Option e-STUDIO202S e-STUDIO203S

e-STUDIO203SD

MR-2019 (RADF)

MR-2018 (ADF)

MY-1034 (1 TRAY UNIT)

Original capacity 50 sheets (56 - 90g/m2(15 - 23.9 lbs.))

Stacking Height: less than 6.5mm or 1/4"

Original size A4 - A5 / 8-1/2" x 14" - 5-1/2" x 8-1/2"

(Landscape)

Original

replacement speed 8-1/2" x 11" about 14 sheets (70%)

A4 about 13 sheets (65%)

Job speed

(Tray1,

Landscape)

Single

copy S to S About 14CPM (8-1/2" x 11")

About 13CPM (A4)

S to D About 10CPM (1 - 30 sheets)(*1)

About 5.6CPM (31 sheets ~)

D to S About 6CPM

D to D About 6CPM (1 - 30 sheets)(*1)

About 5.6CPM (31 sheets ~)

Multi

copy S to S 20CPM

S to D About 13CPM (1 - 30 sheets)(*1)

About 5.6CPM (31 sheets ~)

D to S About 16CPM

D to D About 13CPM (1 - 30 sheets)(*1)

About 5.6CPM (31 sheets ~)

Original placement Face up

Original weight 56 - 90g/m2(15 - 23.9 lbs.)

Mixed feeding No

Original which

cannot Thermal papers, originals with punch

holes for files, be used folded paper,

transparent originals such as OHP films,

stapled or clip used originals with cover up

liquid used, Originals with tape sealed,

originals with high level frictional

coefficient such as photos or catalogs.

Original guide

Document feeder tray

Document

feeder cover

Exit area

Original capacity 50 sheets (56 - 90g/m2(15 - 23.9 lbs.))

Stacking Height: less than 6.5mm or 1/4"

Original size A4 - A5 / 8-1/2" x 14" - 5-1/2" x 8-1/2"

(Landscape)

Original

replacement speed 8-1/2" x 11" about 14 sheets (70%)

A4 about 13 sheets (65%)

Original placement Face up

Original weight 56 - 90g/m2(15 - 23.9 lbs.)

Mixed feeding

(Paper size) No

Original which

cannot Thermal papers, originals with punch holes

for files, be used folded paper, transparent

originals such as OHP films, stapled or clip

used originals with cover up liquid used,

Originals with tape sealed, originals with

high level frictional coefficient such as

photos or catalogs.

Exit area

Original guide

Document feeder tray

Peep hole

Document

feeder cover

MR-2019/2018/MY-1034 GENERAL 1 - 2

C. MY-1034 (250-Sheet Paper Feed Unit)

The paper feed unit provides the convenience of increased paper

capacity for the copier and a greater choice of paper sizes readily

available for copying.

Part names

Specifications

Copy paper size A4 - A5 / 8-1/2" x 14" - 5-1/2" x 8-1/2"

(Landscape)

How to change the

paper size Guide can be adjusted in trays. Cannot be

set in the user simulation.

Paper type setting Not available

Default size setting AB system A4

Inch system 8-1/2" x 11"

Paper weight 56 - 80g/m2(15 - 21 lbs.)

Paper capacity 250 sheets (56 - 80g/m2(15 - 21 lbs.))

Paper type Plain paper, Recycled paper

Paper remaining

quantity detection Not available

Tray

Side cover

MR-2019/2018/MY-1034 UNPACKING AND INSTALLATION 2 - 1

[2] UNPACKING AND INSTALLATION

1. MR-2018/2019 Installation

The installing procedures below are described for the MR-2018.

The installing procedures for the MR-2019 are the same as below.

Turn the main switch to the “OFF” position and remove the power

plug from the outlet.

1) Remove the document cover.

Remove the document cover from the copier.

2) Remove the rear cabinet.

Remove the three screws and then remove the rear cabinet.

3) Replace the right glass holder (For Europe only).

<1> Remove the two screws, and remove the right exterior

OC.

<2> Attach the right glass holder, and fix it with the two screws

which was removed in the above procedure.

Installation manual: 1 sheet

•

Parts included

Right glass holder: 1 pc.

(For Europe only)

Screw (M3 x 8): 1 pc.

Screw (M3 x 6): 1 pc.

MR-2018 Unit (ADF Unit)

MR-2018 Unit (RADF Unit)

"OFF"

MR-2019/2018/MY-1034 UNPACKING AND INSTALLATION 2 - 2

4) Remove the rear cabinet cover.

Remove the screw and then remove the rear cabinet cover.

5) Cut out a part of the rear cabinet cover.

Cut out the cut-out portion of the rear cabinet cover with nip-

pers or the like. (Be careful about the orientation of the nippers

so that the cross section is flat.)

6) Place the ADF on the copier.

Gently place the ADF on the document glass as shown in the

illustration. At this time, be careful not to damage the original

scanning section and the OC mat.

7) Connect the ADF with the copier using the relay harness.

<1> Connect the connector.

<2> Fit the harness to the copier using the supplied screw

(M3 ×8).

<3> Fit the grounding terminal to the copier using the supplied

screw (M3 ×6).

8) Attach the rear cabinet.

Fit the four pawls located at the lower part of the rear cabinet

into the copier and secure the cabinet with the three screws.

OC mat Original scanning

section

Side view

Pawl

★Pawl

MR-2019/2018/MY-1034 UNPACKING AND INSTALLATION 2 - 3

9) Attach the rear cabinet cover.

Fit the harness of the ADF into the cut-out portion of the rear

cabinet cover and secure the cover with the screw.

At this time, check that the three pawls of the rear cabinet cover

are fitted into the rear cabinet.

10) Attach the ADF to the copier.

Attach the ADF by inserting the hinge guide sections of the

ADF into the hinge guides L and R.

11) Insert the power plug into the outlet and turn the main switch of

the copier to the “ON” position.

12) Perform SIM setting.

[MR-2018]

Execute simulation [2] of [26] and enter [1].

[MR-2019]

Execute simulation [2] of [26] and enter [2].

13) Carry out automatic adjustment of ADF scanning position.

Use a black sheet and execute simulation [53]-[08] to carry out

automatic adjustment of ADF scanning position.

For details, see the service manual.

14) Adjust the floating detection level of ADF.

Close the ADF and use simulation code [41]-[06] to adjust the

floating detection level of ADF.

For details, see the service manual.

15) Check the copy ratio, and then check the center displacement

and leading edge image void.

Place an original on the document glass and make a copy.

Then, place an original in the document feeder tray and make a

copy.

If the center of the copy from the document glass is displaced

from the copy from the document feeder, adjust the center

referring to the service manual of e-STUDIO202S.

2. MY-1034 Installation

Turn the main switch to the “OFF” position and remove the power

plug from the outlet.

1) Remove the DV cartridge and the drum cartridge from the

copier.

Open the tray, the side door, and the front cabinet, and then

remove the DV cartridge and the drum cartridge.

Note: Be sure to carry out the operation in the order of (1), (2),

(3), (4), (5), and (6).

"ON"

•

Parts included

Screws (M4 ×16): 4 pcs.

MR-2019/2018/MY-1034 UNPACKING AND INSTALLATION 2 - 4

2) Make the copier upright.

Close the front cover, side cover, and bypass tray, and then

make the copier upright in the orientation shown in the illustra-

tion.

3) Remove the OP gear cover and rubber feet from the bottom of

the copier.

Remove the screw and remove the OP gear cover.

Then, take off and remove the rubber feet.

4) Install the second cassette unit to the copier.

If the second cassette unit is aligned to the copier, it can be

positioned automatically.

Hold the copier lightly to prevent it from toppling down and

secure the second cassette unit with four screws (M4 ×16).

5) Remove the rear cover and connect the connector.

Remove the screw and remove the rear cover.

Then, connect the connector of the second cassette unit to that

of the copier.

6) Attach the rear cover.

Attach the rear cover to its original position and secure it with

the screw (M4 ×12).

7) Return the copier to the normal orientation.

When returning the copier to the normal orientation, gently

return it without giving a shock.

Rubber foot

OP gear cover

Rubber foot

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Toshiba Drucker Handbücher

Toshiba

Toshiba B-570 Bedienungsanleitung

Toshiba

Toshiba B-SX6T Series Benutzerhandbuch

Toshiba

Toshiba B-852 Advance Bedienungsanleitung

Toshiba

Toshiba SureMark 4610 Bedienungsanleitung

Toshiba

Toshiba B-EX4 T1 Series Handbuch

Toshiba

Toshiba B-EP2DL Series Benutzerhandbuch

Toshiba

Toshiba TRST-A10 SERIES Bedienungsanleitung

Toshiba

Toshiba B-SA4T Technische Daten

Toshiba

Toshiba TRST-A00 SERIES Bedienungsanleitung

Toshiba

Toshiba e-STUDIO165 Bedienungsanleitung

Toshiba

Toshiba B-FP3D-GH52-QM-R Bedienungsanleitung

Toshiba

Toshiba B-570-QQ Bedienungsanleitung

Toshiba

Toshiba es525p Bedienungsanleitung

Toshiba

Toshiba TRST-A10 SERIES Bedienungsanleitung

Toshiba

Toshiba GA-1120 Bedienungsanleitung

Toshiba

Toshiba TEC CB-416-T3-QQ Bedienungsanleitung

Toshiba

Toshiba SureMark 4610 1NR Montageanleitung

Toshiba

Toshiba B-SA4TP SERIES Bedienungsanleitung

Toshiba

Toshiba e-STUDIO382P Bedienungsanleitung

Toshiba

Toshiba B-SA4TM-GS12 Bedienungsanleitung

Toshiba

Toshiba GA-1120 Konfigurationshandbuch

Toshiba

Toshiba e-STUDIO810 GA-1140 Bedienungsanleitung

Toshiba

Toshiba B-EP Series Bedienungsanleitung

Toshiba

Toshiba B-EX4 SERIES Technische Daten

Beliebte Drucker Handbücher anderer Marken

Canon

Canon i70 Series Bedienungsanleitung

Evolis

Evolis Elypso Bedienungsanleitung

Kyocera

Kyocera FS-9530DN Bedienungsanleitung

Canon

Canon LASER SHOT LBP-1210 Bedienungsanleitung

Samsung

Samsung BIXOLON SRP-350plusF Bedienungsanleitung

Canon

Canon PIXMA PRO-1 Series Bedienungsanleitung

Canon

Canon PIXMA G3560 Einrichtungshandbuch

Dell

Dell Color Laser Printer 2130cn Bedienungsanleitung

Tektronix

Tektronix Phaser 840 Bedienungsanleitung

Brother

Brother 1440 - HL B/W Laser Printer Kurzanleitung

Fuji Xerox

Fuji Xerox DocuPrint P375 dw Bedienungsanleitung

WOOSIM

WOOSIM PORTI-S30 Bedienungsanleitung

Olivetti

Olivetti PG L2140 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub 224e Bedienungsanleitung

Canon

Canon LBP113w Bedienungsanleitung

Xerox

Xerox DocuColor 5000 Bedienungsanleitung

Canon

Canon PRO-500 Series Einrichtungshandbuch

Epson

Epson ET-7750 Betriebsanleitung