Toshiba B-FP2D Series Bedienungsanleitung

TOSHIBA Potable Printer

B-FP2D SERIES

Document No. SPTM-0325A

Original: Dec., 2019

(Revised: Feb., 2020)

Maintenance Manual

Preliminary version

(IP54 not supported)

WARNING!

Follow all manual instructions. Failure to do so could create safety hazards such as fire or

electrocution.

NOTE:

Failure to follow manual instructions or any unauthorized modification, substitution or change to

this product will void the limited product warranty.

SPTM-0325

CAUTION!

1. This manual may not be copied in whole or in part without prior written permission of Toshiba

tec.

2. The contents of this manual may be changed without notification.

by Toshiba Tec Corporation

1-11-1, Osaki, Shinagawa-ku, Tokyo 141-8562, JAPAN

TABLE OF CONTENTS

Page

1. UNPACKING .............................................................................................................. 1- 1

1.1 Procedure ........................................................................................................................1- 1

1.2 Checks.............................................................................................................................1- 1

2. MAJOR UNIT REPLACEMENT.................................................................................. 2- 1

2.1 Removing the Function Unit ............................................................................................2- 1

2.2 Replacing the Paper Guide Assembly.............................................................................2- 3

2.3 Replacing the Platen Assembly.......................................................................................2- 4

2.4 Replacing the Lower Sensor Assembly...........................................................................2- 5

2.5 Replacing the Logic Card ................................................................................................2- 7

2.6 Replacing the LCD Panel and the Panel Key..................................................................2- 8

2.7 Replacing the Peel Off Unit and Peel Off Sensor............................................................2- 9

2.8 Replacing the WLAN Board Assembly ..........................................................................2- 10

2.9 Replacing the Cover Switch Assembly..........................................................................2- 11

2.10 Replacing the Upper Sensor Assembly ........................................................................2- 12

2.11 Replacing the Thermal Head Assembly ........................................................................2- 14

2.12 Replacing the Driver card ..............................................................................................2- 16

2.13 Replacing the Stepping Motor Assembly.......................................................................2- 17

2.14 Replacing the Battery Terminal .....................................................................................2- 18

3. TROUBLESHOOTING................................................................................................ 3- 1

2-1

1. UNPACKING

1.1 Procedure

1) Open the carton.

2) Unpack the accessories from the carton.

3) Unpack the printer.

NOTE: Keep the carton and pad for future transportation of the printer.

1.2 Checks

1) Check for damage or scratches on the machine.

2) Confirm that none of the accessories are missing.

B-FP3D

B-FP2D

2. MAJOR UNIT REPLACEMENT SPTM-0325

2.1 Removing the Function Unit

2-1

2. MAJOR UNIT REPLACEMENT

WARNING!

1. Disconnect the power cord before installing the main parts.

2. Be careful not to injure your fingers when replacing the main parts.

CAUTION!

1. Since a lot of small moulded parts are used in this printer, care must be taken not to damage or lose

them.

2. Be careful not to damage the print head while removing and reassembling.

3. In the United States, used lithium ion batteries should be returned to the store where you bought the

machine. (USA only)

4. LITHIUM ION BATTERY MUST BE DISPOSED OF PROPERLY.

Caution: Do not handle damaged or leaking lithium ion battery.

5. Before handling the main parts, be sure to discharge static electricity in human body through other

metals. Failure to do this may damage the CPU PC board, print head, etc..

NOTES:

1. Before replacing the main parts, print out the maintenance counter values and the parameter values and keep

the printout. (Refer to Section 4.2 Diagnostics Test in the System Mode Manual.)

After replacing, restore the setting according to the printout.

2. Use precision screwdrivers for replacing the precision components which are installed into the printer.

2.1 Removing the Function Unit

1) Turn off the printer.

2) Press down the battery lever to release the battery cover, and then remove Battery Pack from the printer.

3) Remove the 2-rubber covers located on the front side of the printer. Remove the 2 screws after.

Battery Lever

Battery Pack

T-3x10 Screw

2. MAJOR UNIT REPLACEMENT SPTM-0325

2.1 Removing the Function Unit

2-2

4) Push the open button to open the printer.

5) Remove the screws inside the printer.

6) Remove the fanfold cover and remove the two screws after.

7) Lift the Top cover as shown below. The Function Unit can be removed now.

Open Cover

Open Button

Inside screw

Top Cover

Function Unit

Inside screw

Fanfold cover Screws

2. MAJOR UNIT REPLACEMENT SPTM-0325

2.2 Replacing the Paper Guide Assembly

2-3

2.2 Replacing the Paper Guide Assembly

1) Open the Printer Cover.

2) Remove the screw inside the printer and lift the Paper Guide Assembly.

3) Replace the Paper guide Assembly with a new one, then perform reassembly in the reverse order of

removal.

Function Unit

Screw

Paper Guide Assembly

2. MAJOR UNIT REPLACEMENT SPTM-0325

2.5 Replacing the Logic Card

2-4

2.3 Replacing the Platen Assembly

1) Continue after Section 2.1 Removing the Function Unit.

2) Loosen or remove the two screws as shown blow.

2) Slowly put down the Lower sensor assembly and lift the Platen Assembly. Careful not to damage the flex.

3) Replace the Platen Assembly with a new one, then perform reassembly in the reverse order of removal

Lower Sensor Assembly

Platen Assembly

NOTES:

1. After replacing the Platen, refer to the Setting Operation Manual or System Mode Manual and perform

the following operations.

Perform a RAM clear.

2. Perform a test print and make sure printing is even. (Refer to Section 4.6 in the System Mode Manual.)

If the printing is uneven, make sure the platen ass’y is surely fixed with the hooks.

2. MAJOR UNIT REPLACEMENT SPTM-0325

2.5 Replacing the Logic Card

2-5

2.4 Replacing the Lower Sensor Assembly

1) Refer to item no. 1 in Section 2.2 Replacing the Platen Assembly.

2) Detached the Lower Sensor PCB from the hooks.

3) Push the metal shaft using a pointed tool like a screw driver to remove it together with the two screws.

4) Detach the plastic roller, slowly pull the FFC cable and lift up the Open Cover.

Lower Sensor Assembly

Metal shaft

FFC cable (with

adhesive on the back) Plastic roller

Open Cover

Note: If you want the Lower Sensor PCB only,

you can detach the connector directly.

2. MAJOR UNIT REPLACEMENT SPTM-0325

2.5 Replacing the Logic Card

2-6

5) Remove the black tape on the other side and the bottom side.

6) Slightly pull the Lower Sensor Assembly to detach and access the connector to detach.

7) Replace the Lower Sensor Assembly with a new one, then perform reassembly in the reverse order of removal

Black tape

Black tapes

Lower Sensor Assembly

NOTES:

1. After replacing the Media Sensor, refer to the Setting Operation Manual or System Mode Manual and

perform the following operations.

1. Perform a RAM clear.

2. Perform the sensor adjustment.

2. After replacing the Media Sensor, perform an operation check for the cover open switch as follows.

When the top cover is fully opened, make sure “Cover Open” is displayed on the LCD.

When either side of the top cover is opened, make sure “Cover Open” is displayed on the LCD.

When the top cover is fully closed, make sure the print operation is performed correctly.

If the cover open switch does not operate correctly, this may result from the wrong connection of the sensor

connector, poor contact of the cable, etc. Make sure the sensor connector is surely connected to CN402 on

the CPU PC board and the cable is not broken.

Andere Handbücher für B-FP2D Series

Inhaltsverzeichnis

Andere Toshiba Drucker Handbücher

Toshiba

Toshiba 7FM03281000 Bedienungsanleitung

Toshiba

Toshiba B-SA4TM SERIES Bedienungsanleitung

Toshiba

Toshiba SureMark 4610 Bedienungsanleitung

Toshiba

Toshiba B-EP4DL-GH20-QM-R Bedienungsanleitung

Toshiba

Toshiba e-STUDIO382P Bedienungsanleitung

Toshiba

Toshiba B-EV4 Series Bedienungsanleitung

Toshiba

Toshiba SureMark 4610-SJ6 Bedienungsanleitung

Toshiba

Toshiba TEC B-SP2D Series Bedienungsanleitung

Toshiba

Toshiba 4679 Bedienungsanleitung

Toshiba

Toshiba e-STUDIO500P Bedienungsanleitung

Toshiba

Toshiba HSP100 Bedienungsanleitung

Toshiba

Toshiba GA-1310 Bedienungsanleitung

Toshiba

Toshiba e-studio 80f Bedienungsanleitung

Toshiba

Toshiba B-480-QQ Bedienungsanleitung

Toshiba

Toshiba B-SP2D Series Bedienungsanleitung

Toshiba

Toshiba 1NR Bedienungsanleitung

Toshiba

Toshiba e-STUDIO222CP Bedienungsanleitung

Toshiba

Toshiba e-STUDIO165 Bedienungsanleitung

Toshiba

Toshiba B-FV4D-GS12-QM-R Bedienungsanleitung

Toshiba

Toshiba es525p Bedienungsanleitung

Toshiba

Toshiba B-SP2D Series Bedienungsanleitung

Toshiba

Toshiba TCx 2tn Bedienungsanleitung

Toshiba

Toshiba TRST-A10 SERIES Bedienungsanleitung

Toshiba

Toshiba B-EX4 SERIES Bedienungsanleitung

Beliebte Drucker Handbücher anderer Marken

Canon

Canon i70 Series Bedienungsanleitung

Evolis

Evolis Elypso Bedienungsanleitung

Kyocera

Kyocera FS-9530DN Bedienungsanleitung

Canon

Canon LASER SHOT LBP-1210 Bedienungsanleitung

Samsung

Samsung BIXOLON SRP-350plusF Bedienungsanleitung

Canon

Canon PIXMA PRO-1 Series Bedienungsanleitung

Canon

Canon PIXMA G3560 Einrichtungshandbuch

Dell

Dell Color Laser Printer 2130cn Bedienungsanleitung

Tektronix

Tektronix Phaser 840 Bedienungsanleitung

Brother

Brother 1440 - HL B/W Laser Printer Kurzanleitung

Fuji Xerox

Fuji Xerox DocuPrint P375 dw Bedienungsanleitung

WOOSIM

WOOSIM PORTI-S30 Bedienungsanleitung

Olivetti

Olivetti PG L2140 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub 224e Bedienungsanleitung

Canon

Canon LBP113w Bedienungsanleitung

Xerox

Xerox DocuColor 5000 Bedienungsanleitung

Canon

Canon PRO-500 Series Einrichtungshandbuch

Epson

Epson ET-7750 Betriebsanleitung