TP-Link WBS210 Bedienungsanleitung

7106506431 REV1.0.0

Specifications are subject to change without notice. TP-LINK is

a registered trademark of TP-LINK TECHNOLOGIES CO., LTD.

Other brands and product names are trademarks or

registered trademarks of their respective holders.

No part of the specifications may be reproduced in any form

or by any means or used to make any derivative such as

translation, transformation, or adaptation without permission

www.tp-link.com

Outdoor Wireless Base Station

Installation Guide

› English

› Български

› Čeština

› Қазақша

› Lietuvių

› Magyar

›Polski

› Русский язык

› Română

› Slovenčina

› Srpski jezik

› Українська мова

CONTENTS

English

Български

Čeština

Қазақша

Lietuvių

Magyar

Polski

Русский язык

Română

Slovenčina

Srpski jezik

Українська мова

Hardware Installation

Use an adequate Ethernet cable to

connect the LAN0 (POE IN) port. The

length of cable is up to 60m for

steady power supply. Shielded CAT5e

(or above) cable with an integrated

ground wire is recommended.

Firmly grasp the rear of the interface

cover and pull it downward.

The Outdoor Wireless Base Stations require external antenna that

corresponds to your network environment. It is recommended to buy

and use TP-LINK’s matching antennas.

Connect Cables

TP-LINK's Matching

Antenna

Recommended

Antenna Type

Sector Antenna

Dish Antenna TL-ANT2424MD (2.4GHz)

TL-ANT5830MD (5GHz)

TL-ANT2415MS (2.4GHz)

TL-ANT5819MS (5GHz)

English

Align the mounting tabs on the back

of the Base Station with the four slots

of the mounting bracket. Push and

slide the Base Station downward

until it locks into place.

Affix the waterproof rubber insert to

the underside of the device for

waterproofing and replace the cover

until it firmly locks into place.

Sector antenna is used as a demonstration below.

Connect the RF Cables to the Base

Station.

Mount Antenna

Option1: Mounting the Base Station on an Antenna

Mount the Base Station on an antenna with a suitable mounting

bracket or on a pole for the antenna without the mounting bracket.

English

Attach the protective cap. Push and

slide the protective cap down over the

Base Station until it firmly locks into

place.

Connect the RF cables from the Base

Station to the corresponding

connectors on the antenna.

Loosen and completely remove the

end of the metal strap by turning the

captive screw counterclockwise with

a flathead screwdriver.

Lead the end of the metal strap

through the back of the Base Station.

Option 2: Mounting the Base Station on a Pole

English

Position the Base Station and wrap

the metal strap around the pole.

Feed the end back through the

screw-block and turn the screw

clockwise to tighten the metal strap

using a flathead screwdriver until

the Base Station is secure.

Connect the RF cables from the Base Station to the corresponding

connectors on the antenna.

Connect the Ethernet cable from the Base Station to the PoE port

of the PoE adapter.

Connect an Ethernet cable from your LAN device (a computer,

router or switch) to the LAN port on the PoE adapter.

Connect the power cord to the power port on the PoE adapter

and plug it into an electrical outlet.

Connect the Base Station to a Power over Ethernet (PoE) adapter as

follows:

Power On

English

Open a web browser, type http://192.168.0.254 into the address

field and press Enter (Windows) or Return (Mac). It is recommended

to use the latest version of Google Chrome, Firefox or Safari.

Configuration with PharOS

Before accessing the PharOS Web Interface, you need to assign a

static IP address 192.168.0.X (X ranges between 2 and 253,e.g.

192.168.0.10) to your computer.

Configure the Base Station

192.168.0.254

The typical topology is as follows. A wireless bridge is built between

two locations that are far from each other. Follow the instructions

below to configure the Access Point and the Client.

Access point

LAN:192.168.0.254

Client

LAN:192.168.0.2

Enter admin for both User Name and Password, then select the

Language from the drop-down list. Read and agree the terms of

use, then click Login.

Change

the

default

User

Name

and

Password

protect

your

Base Station. Let’s start configuring the Base Staion.

For subsequent logins, use the new username and password.

English

1. Log in to PharOS and go to the Quick Setup page.

2. Operation Mode: Select Access Point and click Next.

3. LAN Settings: Click Next.

4. Wireless AP Settings:

a. Create a new SSID (Network name) for your wireless

network.

b. Select WPA-PSK/WPA2-PSK for the Security method and

create a PSK Password to protect your AP.

c. Enter the distance between the Access Point and the Client

into the Distance Setting field.

d. Select the MAXtream checkbox, and click Next.

5. Finish: Verify your settings and click Finish to complete the

configuration.

Configure the Access Point (AP)

Configure the Client

1. Log in to PharOS and go to the Quick Setup page.

2. Operation Mode: Select Client and click Next.

3. LAN Settings: Change the IP Address to 192.168.0.X (X ranges

between 2 and 253), the same subnet with the access point,

and click Next.

4. Wireless Client Settings:

a. Click Survey and select the SSID of the Access Point in the

AP list, then click Connect.

b. Select WPA-PSK/WPA2-PSK from the Security option, enter

the same PSK password and distance value of the Access

Point, then click Next.

5. Finish: Verify your settings and click Finish to complete the

configuration.

English

Инсталация на хардуера

Използвайте достатъчно дълъг

Ethernet кабел, за да го свържете

към LAN0 порта (вход за POE).

Дължината на кабела е до 60m за

стабилно подаване на захранване.

Препоръчва се екраниран кабел

категория CAT5e (или по-висока) с

вграден заземителен проводник.

Хванете здраво задната страна на

капака на портовете и я издърпайте

надолу.

За работата на безжичните базови станции за външен монтаж са

необходими външни антени, които да съответстват на мрежовата

среда. Препоръчва се закупуването и използването на

съответстващите антени на TP-LINK.

Свързване на кабелите

Съответстваща антена на

TP-LINK

Препоръчителен

тип антена

Секторна антена

Параболична антена

(тип "чиния")

TL-ANT2424MD (2.4GHz)

TL-ANT5830MD (5GHz)

TL-ANT2415MS (2.4GHz)

TL-ANT5819MS (5GHz)

Български

Подравнете монтажните крачета на

гърба на базовата станция с

четирите отвора на монтажната

скоба. Натиснете и плъзнете

базовата станция надолу, докато

щракне в мястото си.

Поставете гумената вложка за

осигуряване на водоустойчивост

на долната страна на устройството

и сложете обратно капака докато

щракне в мястото си.

В илюстрациите по-долу е показана секторна антена.

Свържете радиочестотните кабели

към базовата станция.

Монтиране на базовата станция

Опция 1: Монтиране на базовата станция върху антената

Монтирайте базовата станция върху антената с подходящата

монтажна скоба, или върху стълба на антената без използване на

монтажната скоба.

Български

Andere Handbücher für WBS210

Inhaltsverzeichnis

Sprachen:

Andere TP-Link Zubehör Handbücher

TP-Link

TP-Link HS100 Bedienungsanleitung

TP-Link

TP-Link TL-PB10400 Bedienungsanleitung

TP-Link

TP-Link HS100 Bedienungsanleitung

TP-Link

TP-Link PB50 Bedienungsanleitung

TP-Link

TP-Link Tapo T110 Bedienungsanleitung

TP-Link

TP-Link TL-PBB3000 Betriebsanleitung

TP-Link

TP-Link Tapo Smart Contact Sensor Bedienungsanleitung

TP-Link

TP-Link tapo T310 Bedienungsanleitung

TP-Link

TP-Link Tapo P110 Bedienungsanleitung

TP-Link

TP-Link TL-PBG6700 Bedienungsanleitung

TP-Link

TP-Link Kasa Smart KP200 Bedienungsanleitung

TP-Link

TP-Link tapo T310 Bedienungsanleitung

TP-Link

TP-Link HS105 Bedienungsanleitung

TP-Link

TP-Link KP115 Bedienungsanleitung

TP-Link

TP-Link MS100 Bedienungsanleitung

TP-Link

TP-Link CS100 Bedienungsanleitung

TP-Link

TP-Link Tapo Camera Bedienungsanleitung

TP-Link

TP-Link Kasa Smart KP105 Series Bedienungsanleitung

TP-Link

TP-Link TL-PB10000 Bedienungsanleitung

TP-Link

TP-Link Tapo D130 Bedienungsanleitung

TP-Link

TP-Link Kasa Smart KP400 Bedienungsanleitung

TP-Link

TP-Link Tapo Camera Bedienungsanleitung

TP-Link

TP-Link TL-PBB6000 Betriebsanleitung

TP-Link

TP-Link HS100 Bedienungsanleitung

Beliebte Zubehör Handbücher anderer Marken

Hillco

Hillco 2810 Bedienungsanleitung

Siemens

Siemens QSA2700D Bedienerhandbuch

Contours

Contours ZY024 Bedienungsanleitung

Saivod

Saivod VS621 Bedienungsanleitung

Virtuox

Virtuox VirtuCLEAN 2.0 Bedienungsanleitung

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Bedienungsanleitung

Z-Wave

Z-Wave HSD-200Z Bedienungsanleitung

turck

turck FMX-IM-2UPLI63FX Bedienungsanleitung

Decagon Devices

Decagon Devices 10HS Bedienungsanleitung

UPPAbaby

UPPAbaby Cup Holder Bedienungsanleitung

Elko

Elko SmartSensor Leakage Wireless Bedienungsanleitung

Grizzly

Grizzly H8371 Bedienungsanleitung

Panasonic

Panasonic HG-T Series Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 250 Series Referenzhandbuch

DigiDesign

DigiDesign 888/24 I/O Bedienungsanleitung

PROZIS

PROZIS QUAY Bedienungsanleitung

patagonia

patagonia PSI Vest Bedienungsanleitung

SFC Energy

SFC Energy EFOY GO! Bedienungsanleitung