TP-Link TL-SF1008P Bedienungsanleitung
User Guide
TL-SF1008P
8-Port 10/100Mbps Desktop PoE Switch
Rev：1.0.2
7106503183
COPYRIGHT & TRADEMARKS
Specifications are subject to change without notice.
is a registered trademark of TP-LINK
TECHNOLOGIES CO., LTD. Other brands and product names
are trademarks or registered trademarks of their respective
holders.
No part of the specifications may be reproduced in any form or
by any means or used to make any derivative such as
translation, transformation, or adaptation without permission
from TP-LINK TECHNOLOGIES CO., LTD. Copyright © 2008
TP-LINK TECHNO- LOGIES CO., LTD. All rights reserved.
http://www.tp-link.com
FCC STATEMENT
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following
measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and
receiver.
•Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
•Consult the dealer or an experienced radio/ TV
technician for help.
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions:
1) This device may not cause harmful interference.
2) This device must accept any interference received,
including interference that may cause undesired
operation.
Any changes or modifications not expressly approved by the
party responsible for compliance could void the user’s authority
to operate the equipment.
CE Mark Warning
This is a class B product. In a domestic environment, this
product may cause radio interference, in which case the user
may be required to take adequate measures.
SAFETY NOTICES
Cautions
Do not use this product near water, for example, in a wet
basement or near a swimming pool.
Avoid using this product during an electrical storm. There may
be a remote risk of electric shock from lightning.
CONTENT
Package Contents ......................................................1
Chapter 1. Introduction of the Product ..........................1
1.1 Overview of the Product ...................................... 1
1.2 Convention ............................................................ 2
1.3 Features................................................................. 2
Chapter 2. Installation ................................................3
2.1 Mounting the Switch on a Desk........................... 3
2.2 Power On ............................................................... 4
Chapter 3. Identifying External Components ...................4
3.1 Front Panel ............................................................ 4
3.2 Rear Panel ............................................................. 6
Appendix A: Specifications..........................................8
1
Package Contents
The following items should be found in your box:
¾One TL-SF1008P 8-Port 10/100Mbps Desktop PoE Switch
¾One DC Power Adapter
¾Four rubber cushions to be used under the switch
¾This User Guide
Note
Make sure that the box contains the above items. If any of the
listed items are damaged or missing, please contact with your
distributor.
Chapter 1. Introduction of the Product
Thank you for choosing the TL-SF1008P 8-Port 10/100Mbps
Desktop PoE Switch.
1.1 Overview of the Product
The TL-SF1008P 8-Port 10/100Mbps Desktop PoE Switch
provides the seamless network connection, which integrates
100Mbps Fast Ethernet and 10Mbps Ethernet network
capabilities.
This PoE Switch is also a Power Sourcing Equipment (PSE*).
Four of the eight Auto-Negotiation RJ45 ports (port-1~port-4) on
the switch support Power over Ethernet (PoE*) function, which
can automatically detect and supply power with those IEEE
802.3af-complaint powered devices (PDs*).
2
1.2 Convention
The Switch or TL-SF1008P mentioned in this User Guide stands
for TL-SF1008P 8-Port 10/100Mbps Desktop PoE Switch
without any explanation.
1.3 Features
¾Complies with IEEE802.3, IEEE802.3u, IEEE802.3af
standards
¾8 10/100Mbps Auto-Negotiation RJ45 ports with 4-port PoE
function (port-1~port-4), all of them support Auto-MDI/MDIX
¾Supports PoE power up to 15.4W for each PoE port
¾Supports PoE power up to 53W for PoE ports
¾Supports PoE IEEE802.3af compliant PDs
¾Supports IEEE802.3x flow control for Full-duplex Mode and
backpressure for Half-duplex Mode
¾1K entry MAC address table of the TL-SF1008P with auto-
learning and auto-aging
*PSE: a device (switch or hub for instance) that will provide power in a PoE
setup.
*PoE: This technology describes a system to transmit electrical power, along
with data, to remote devices over standard twisted-pair cable in an
Ethernet network.
*PD: a device powered by a PSE and thus consumes energy. Examples
include powering IP telephones, wireless LAN access points, network
cameras, network hubs, embedded computers etc.
3
¾LED indicators for monitoring power, link, activity and speed
¾External power adapter supply
Chapter 2. Installation
During the installation procedure, please only use the
accessories equipped with the switch.
2.1 Mounting the Switch on a Desk
To install the Switch, please follow the steps:
1) You can place the Switch on a flat desk.
2) Please insert the power adapter carefully to the power
socket of the switch, and then connect it properly to a power
source through the cable of the switch.
3) Ensure adequate ventilation space around the switch for
dissipating heat and air.
Note
1) Please avoid any heavy thing placed on the switch.
2) Make sure the power is off before unplugging the power
adapter.
4
2.2 Power On
The TL-SF1008P Switch can be used with DC power supply.
Powering on the Switch, it will automatically initialize and its LED
indicators will respond as follows:
1) All the LED indicators except PoE ports LED will light syn-
chronously at first, then all of them included Link/Act LED
(green), 100Mbps LED (green) and PoE MAX LED (red), will
light off at once, which indicates the system initialized well.
2) The Power indicator will light all the time.
Note
If the LED indicators don’t respond as described above, please
check the power supply and its connection.
Chapter 3. Identifying External Components
This Chapter describes the front panel, rear panel and LED indi-
cators of the Switch.
3.1 Front Panel
Figure 3-1 TL-SF1008P Switch Front Panel
The Switch’s LEDs are located on the front panel.
Andere Handbücher für TL-SF1008P
6
Inhaltsverzeichnis
Andere TP-Link Schalten Handbücher
TP-Link
TP-Link Tapo S500D Bedienungsanleitung
TP-Link
TP-Link TL-SG3109 - Switch Bedienungsanleitung
TP-Link
TP-Link TL-SG608E Bedienungsanleitung
TP-Link
TP-Link TL-SG2452 Bedienungsanleitung
TP-Link
TP-Link JetStream TL-SG3452X Bedienungsanleitung
TP-Link
TP-Link JetStream TL-SL5428E Bedienungsanleitung
TP-Link
TP-Link TL-SF1006P Bedienungsanleitung
TP-Link
TP-Link JetStream TL-SG2210P Bedienungsanleitung
TP-Link
TP-Link JetStream TL-SG2008 Bedienungsanleitung
TP-Link
TP-Link JetStream TL-SG3424 Bedienungsanleitung
TP-Link
TP-Link JetStream T1500-28PCT Bedienungsanleitung
TP-Link
TP-Link UC400 Bedienungsanleitung
TP-Link
TP-Link LS105LP Bedienungsanleitung
TP-Link
TP-Link JetStream TL-SL3452 Bedienungsanleitung
TP-Link
TP-Link JetStream T2700G-28TQ Bedienungsanleitung
TP-Link
TP-Link TL-SG2216 Bedienungsanleitung
TP-Link
TP-Link TL-SF1005D Bedienungsanleitung
TP-Link
TP-Link TL-SX1008 Bedienungsanleitung
TP-Link
TP-Link Tapo S200D Bedienungsanleitung
TP-Link
TP-Link Kasa KS200M Bedienungsanleitung
