Trikke E-Kit Bedienungsanleitung

1. Verify that your E-Kit contains all of the following materials for proper

installation:

•Wheel and motor assembly X1

•Battery pack controller bag and bracket assembly X1

•Throttle X1

•Full sized handle grip X1

•Half sized handle grip X1

•Throttle sleeve X1

•Circular half-brackets X3

•Circular T-shaped half-bracket X1

•5mm hex-bolts X6

•5mm Allen wrench X1

•3mm Allen wrench X1

•Zip-ties X2

•Trikke emblem badge X1

•Trikke Tribred front post sticker X1

•2” Clear alignment stickers X2

•1” Clear alignment sticker X1

•Clear wire bundler stickers X3

2. Remove the existing Trikke sticker from the front post. Also, remove

the water bottle cage from the front post if you have one installed.

3. Disassemble the brake cables from the brake handle.

•Align the brake cable adjustment screws (arrow) so that

the slot in the screws line up with the slot in the brake

handle. This will allow the brake cable to come free out

of the front of the brake handle.

•Squeeze the brake handle so that the small metal

cylinder attached to the end of the brake cable is visible.

•Align the brake cable and the metal cylinder with the

brake handle slot so that the cable can come free of the

brake handle completely.

•Repeat the above steps to disassemble the other brake

cable from the other brake handle.

4. Free the brake cables from the cable bracket at the lower end of

the front post so that the brake cables can be pulled to the rear

of the Trikke. This will allow installation of the E-Kit without

interfering with the brake cables.

5. Loosen the two lower 5mm Allen socket bolts of the front wheel fork

where the fork attaches to the front post.

6. Press the alignment pin and remove the front wheel assembly. Note:

You may want to place the front post stem on a piece of wood or in

the plastic Trikke packaging block that originally came with the Trikke

to avoid damaging the Trikke or the floor.

7. Remove both existing handle grips.

•Some handle grips require that a phillips-head screw be

removed prior to removing the handle grip. If this is the

case, remember to also remove the cap inside the

handlebar so that it does not fall inside the handlebar

and rattle around as you ride.

•Removal of the handle grips requires a lot of effort. You

may want to use a hot air blow gun to heat the material

before removing it. Use extreme caution as this may

melt the handle grip material and or cause a fire.

8. Install the Throttle on the right side of the handlebar.

•The throttle should slide all the way to the brake handle.

•Once the throttle is against the brake handle, rotate the

throttle until the stop located on the inner face of the

throttle is resting against the brake handle. This will

align the throttle to the proper position.

•Insert the plastic throttle sleeve over the handlebar so

that the sleeve slides inside the throttle. The sleeve

flange will stop the sleeve against the throttle.

•Install the half-sized handle grip over the remaining right

side of the handlebar.

•Tighten the 3mm Allen socket bolt located on the

underside of the throttle making sure to keep the

throttle aligned as described above.

9. Install the full-sized handle grip on the left side of the handlebar.

10. Place one of the 2” clear alignment stickers 0.5” below the

upper brake cable bracket.

11. Place the second 2” clear alignment sticker 0.75” below the

lower brake cable bracket.

0.5”

12. Install the bag and bracket assembly – Option A.

•Fold the Trikke into its closed and locked position. Place

the battery pack controller bag and bracket assembly

between the arms of the Trikke, but beneath the front

post.

•Align the bag assembly with the half-circle brackets

holding the front post and the exposed bracket toward

the hinge (the bottom when unfolded) of the Trikke.

•Align the brackets with the top of the brackets aligned

with the top of the clear alignment stickers.

•Install two half-circle brackets with four 5mm Allen socket

bolts to the bag assembly. Make sure to keep the spacing

between each side of the bracket the same. This will

ensure an even tension for each bolt and will prevent

stripping the brackets and bolts.

•Unfold the Trikke to its upright and locked position.

Allow the bag assembly to “seat” by pushing down on the

assembly. Make sure to keep the bag assembly centered

and aligned with the top edges of the clear alignment

stickers.

•

Finishing

tightening

the

Allen

socket

bolts

•

Finishing

tightening

the

Allen

socket

bolts

13. Install the bag and bracket assembly – Option B.

•This procedure is the same as Option A above except do

not fold the Trikke before installation. This will require

some strength and is possibly a two person installation.

14. Reassemble the brakes.

•Feed the brake cables through the spaces located in

the front center of each bracket. Do not set the brake

cables in the brake cable brackets on the front post

(arrows).

•Cross the brake cables once behind the post and once

more in front of the post. This will ensure the left

brake handle will apply the left brake and the same for

the right side.

•Reverse the brake cable detachment procedure of step

3 above. Note: if there is not enough brake cable

visible from the brake cable sleeve, just push the sleeve

down the cable until enough brake cable is showing.

This is why we do not set the brake cables into the

brake cable brackets until later.

•Set the brake cable sleeves into the brake cable

brackets on the front post (arrows).

•Squeeze the brake handle. There should be space

between the brake handle and the handle grip at

maximum

strength

The

adjustment

screws

located

maximum

strength

The

adjustment

screws

located

the brake handle can be used to add or remove tension

from the brake line (lower arrow).

15. Tape the throttle cable to the brake cable using the three clear

cable bundling stickers provided.

16. Unzip the top flap of the bag assembly and feed the throttle

cable wires through the hole located at the top front center of

the bag assembly.

•Connect the two throttle cable connecters to the

controller wires which are labeled with a throttle tag.

17. Install the 1” clear alignment sticker.

•Turn the Trikke upside down and rest the Trikke on its

handlebar and foot rests.

•Remove the serial number sticker located on the

backside of the front post near the front wheel

assembly. Replace the sticker on the backside of the

front post just under the bag assembly bracket.

•Align the 1” clear alignment sticker with the bottom

edge of the front post and wrap around the front post.

18. Install the front wheel motor assembly turn-limiter bracket.

•Install the half-circle T-bracket and half-circle bracket

with the remaining Allen socket bolts.

•Align the half-circle bracket with the bottom edge of the

front post. The half-circle T-bracket should be on the

front side of the Trikke with the other bracket on the

backside. Make sure to center the brackets so that the

T-bracket is perfectly aligned with the front side of the

front post.

19. Install the front wheel motor assembly.

•Slide the motor assembly over the steering post.

•Press in the steering post pin and slide the motor

assembly over it until the pin snaps into place.

•Note: The front wheel motor assembly plastic fender may

be loose. If this is the case, try the following techniques:

i. Remove the fender and use superglue around

the base of the sleeve where the sleeve will

contact the inner tube of the motor assembly

fork. Quickly place the fender assembly in place

and allow the glue to set.

ii. Remove the fender assembly and expand the

outer radius of the fender sleeve by heating the

sleeve with a hot air blow gun. Use Caution with

this technique as the heat gun may melt the

fender material or cause a fire. Once the sleeve

is heated, use a socket from a socket-wrench set

that is one size larger than the current inner

radius of the sleeve and push the socket through

the sleeve. This will expand the radius of the

sleeve. Install the fender back into place.

•Tighten the 5mm Allen socket bolts.

Andere Trikke Roller Handbücher

Trikke

Trikke T5 JOGO Bedienungsanleitung

Trikke

Trikke POSITRON 60V AWD Bedienungsanleitung

Trikke

Trikke Bikke Bedienungsanleitung

Trikke

Trikke uPT Bedienungsanleitung

Trikke

Trikke Tribred tree rein Bedienungsanleitung

Trikke

Trikke Pon-e 48V Bedienungsanleitung

Trikke

Trikke T67s Bedienungsanleitung

Trikke

Trikke T8 Bedienungsanleitung

Trikke

Trikke DEFENDER 48V 2WD Bedienungsanleitung

Trikke

Trikke eV5 Bedienungsanleitung

Trikke

Trikke T7 Bedienungsanleitung

Trikke

Trikke T8 Bedienungsanleitung

Trikke

Trikke Tribred Pon-e Bedienungsanleitung

Trikke

Trikke T5 JOGO Bedienungsanleitung

Trikke

Trikke FREEDOM Bedienungsanleitung

Trikke

Trikke Colt Bedienungsanleitung

Trikke

Trikke DEFENDER Bedienungsanleitung

Beliebte Roller Handbücher anderer Marken

TEKTRO

TEKTRO CHEETAH Bedienungsanleitung

Douglas

Douglas Vespa Sprint Installationsanleitung

PLAYTIVE

PLAYTIVE AS-2448 Bedienungsanleitung

Ebinger

Ebinger DONKEY XL Bedienungsanleitung

Flyer

Flyer Mountain Benutzerhandbuch

BackCountry eBikes

BackCountry eBikes Storm Bedienungsanleitung

equipmed

equipmed FreeRoam II Bedienungsanleitung

Yoto

Yoto Lion Bedienungsanleitung

WESTHILL BIKES

WESTHILL BIKES LINK Bedienungsanleitung

BAnff

BAnff eProdigy series Bedienungsanleitung

Winther

Winther 475 Bedienungsanleitung

Jetson

Jetson JBZL17 Bedienungsanleitung

First Choice Mobility

First Choice Mobility Roma Medical Corella S741 Bedienungsanleitung

Carrera

Carrera impel Bedienungsanleitung

Afikim

Afikim Superlight SL-3 Bedienungsanleitung

CareCo

CareCo ZOOM Bedienungsanleitung

Douglas

Douglas Vespa G.S. Bedienungsanleitung

Gazelle

Gazelle with BOSCH System Bedienungsanleitung