Ubiquiti AirFiber AF-24-US Bedienungsanleitung

24 GHz Point-to-Point

1.4+ Gbps Radio

Model: AF-24

Introduction

Thank you for purchasing the Ubiquiti Networks® airFiber® 24GHz

Point-to-Point Radio. This Quick Start Guide is designed to guide

you through installation and also includes the warranty terms.

Package Contents

airFiber AF-24 Pole Mount Bracket Pole Clamps

(Qty. 2)

Cable Ties

(Qty. 3)

Carriage Bolts

(Qty. 4)

Flat Washers

(Qty. 4)

Split Lock Washers

(Qty. 4)

Hex Nuts

(Qty. 4)

24 GHz Point to Point

1.4+ Gbps Radio

Model: AF-24

GigE PoE Adapter

(50V, 1.2A)

Power Cord airFiber AF-24

Quick Start Guide

earth grounding must be used as conditions of product warranty. TOUGHCable™is designed for

outdoor installations. It is the professional installer’s responsibility to follow local country regulations,

including operation within legal frequency channels, output power, and Dynamic Frequency Selection

(DFS) requirements.

airFiber AF-24 Quick Start Guide

Hardware Overview

Side

24 GHz

Alignment Bracket

Elevation

Adjustment

Azimuth

Adjustment

Ground

Bonding Point

Lock Bolts

Hardware Overview

Back

Lock Bolts

Azimuth

Adjustment

24 GHz

Lock Bolts

Cover Lock

Elevation

Adjustment

Port Cover

airFiber AF-24 Quick Start Guide

Interfaces

Reset Data Aux ConfigLED Display

Interface Description

Reset

To reset to factory defaults, press and hold the Reset

button for more than five seconds while the unit is

powered on.

Data 10/100/1000 Mbps port handles all user traffic.

Aux Port for audio tone aiming.

LED Display Digital display used for power, status, and mode

information.

Config

10/100 Mbps, secured port for configuration. By

default, this is the only port that can monitor,

configure, and/or update firmware.

LEDs

Link/Act

Speed GPS

Modulation Link/Act

SpeedRX Power

Master/Slave RF Link Status

Hardware Overview

LED State Status

Data

Speed Off 10/100 Mbps

On 1000 Mbps

Link/Act

Off No Ethernet Link

On Ethernet Link Established

Random Flashing Ethernet Activity

Aux

GPS

Off No GPS Synchronization

On Operational (Strong Signal)

Normal Flash* Operational (Weak Signal)

Modulation

Off ¼x or 1x (QPSK SISO)

Short Flash* 2x (QPSK MIMO)

Normal Flash* 4x (16QAM MIMO)

Long Flash* 6x (64QAM MIMO)

LED Display

RX Power

(-dBm)

Number Decodable RX Signal

Flashing Number Undecodable RX Signal

Overload Condition

Master/

Slave

Off Slave Mode

On Master Mode

RF Link

Status

Off RF Off

Short Flash* Syncing

Normal Flash* Beaconing

Long Flash* Registering

On Operational

Config

Speed Off 10 Mbps

On 100 Mbps

Link/Act

Off No Ethernet Link

On Ethernet Link Established

Random Flashing Ethernet Activity

* Short Flash (1:3 on/off cycle)

Normal Flash (1:1 on/off cycle)

Long Flash (3:1 on/off cycle)

airFiber AF-24 Quick Start Guide

Installation Requirements

• 17 mm wrench

• 13 mm socket wrench or driver

• Clear line of sight between airFiber radios

• Clear view of the sky for proper GPS operation

• Mounting location with < 0.5° displacement due to twist and

sway under wind loading

• Mounting point:

• At least 1 meter below the highest point on the structure

• For tower installations, at least 3 meters below the top of the

tower

• Ground wires – min. 8 AWG (10 mm2) and max. length: 1 meter.

As a safety precaution, ground the airFiber radios to grounded

masts, poles, towers, or grounding bars.

WARNING: Failure to properly ground your airFiber

units will void your warranty.

• (Recommended) 2 Outdoor GigE PoE surge protectors

Note: For guidelines about grounding and lightning

protection, follow your local electrical regulatory codes.

• Outdoor, shielded Category 5e (or above) cabling and shielded

RJ-45 connectors should be used for all wired Ethernet

connections. Category 6 is required for installations with long

cable runs (up to 100 m).

We recommend that you protect your networks from harmful

outdoor environments and destructive ESD events with

industrial-grade, shielded Ethernet cable from Ubiquiti Networks

For more details, visit www.ubnt.com/toughcable

Installation Overview

We recommend that you configure your paired airFiber radios

before mounting. Below is an overview of the installation with

specific details on the following pages:

• Connect Power over Ethernet to the Data port, and connect an

Ethernet cable between your computer and the Config port.

• Configure device settings in the airFiber Configuration Interface.

Connecting Power over Ethernet

• Once configuration is complete, disconnect the cables to move

the airFiber radios.

• Reconnect at the site.

• After you have mounted the airFiber radios, establish and

optimize the RF link.

Connecting Power over Ethernet

1. Turn the Cover Lock to the Unlocked icon. Slide the Port Cover

down to remove it.

24 GHz

2. Connect an Ethernet cable to the Data port.

airFiber AF-24 Quick Start Guide

3. Connect the Ethernet cable from the Data port to the POE port

on the GigE PoE Adapter.

4. Connect the Power Cord to the GigE PoE Adapter, and then plug

the Power Cord into a power outlet.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Ubiquiti Drahtloser Zugangspunkt Handbücher

Ubiquiti

Ubiquiti NBE-5AC-Gen2 Bedienungsanleitung

Ubiquiti

Ubiquiti Rocket5AC R5AC-PTP Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi nanoHD UAP-nanoHD Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi nanoHD AP Bedienungsanleitung

Ubiquiti

Ubiquiti airFiber AF 60 Bedienungsanleitung

Ubiquiti

Ubiquiti LiteBeam LBE-5AC-16-120 Bedienungsanleitung

Ubiquiti

Ubiquiti NanoBeam 5AC Gen2 Bedienungsanleitung

Ubiquiti

Ubiquiti Rocket 5ac PtMP Bedienungsanleitung

Ubiquiti

Ubiquiti M5 GPS Rocket M Series Bedienungsanleitung

Ubiquiti

Ubiquiti NBE-5AC-Gen2 Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStationM Series Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi Dream Machine Beacon Bedienungsanleitung

Ubiquiti

Ubiquiti UAP-AC-LITE Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi AP BeaconHD Bedienungsanleitung

Ubiquiti

Ubiquiti NanoBeam NBE2ACN Bedienungsanleitung

Ubiquiti

Ubiquiti NanoBeam M2 Bedienungsanleitung

Ubiquiti

Ubiquiti UBB Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation 5AC Loco Bedienungsanleitung

Ubiquiti

Ubiquiti LiteBeam LBE-5AC-LR Bedienungsanleitung

Ubiquiti

Ubiquiti M900 Bedienungsanleitung

Ubiquiti

Ubiquiti NanoBeam ac NBE-5AC-16 Bedienungsanleitung

Ubiquiti

Ubiquiti airFiber AF-5XHD Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi AC MESH PRO Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation NSM2 Bedienungsanleitung

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung

Cisco

Cisco Aironet 1550 Series Bedienungsanleitung

Aruba

Aruba IAP-335 Bedienungsanleitung

Advantek Networks

Advantek Networks AWN-AP-54MR Bedienungsanleitung

IP-COM

IP-COM AP355 Bedienungsanleitung

Buffalo

Buffalo AirStation WLA-L11G Bedienungsanleitung

EnGenius

EnGenius EnStationACv2 Bedienungsanleitung

D-Link

D-Link DAP-3662 Bedienungsanleitung

xG Technology

xG Technology xMax CN1300 Bedienungsanleitung

Widelink

Widelink ezWave WAP-1100 Series Bedienungsanleitung

Edimax

Edimax CAP1200 Bedienungsanleitung

Aruba

Aruba AP-203R Bedienungsanleitung

LuXout Shades

LuXout Shades LUXSHADE MOTION Bedienungsanleitung

CreatComm

CreatComm TB5F Bedienungsanleitung

SineDigital

SineDigital MW-1500AP(H) Bedienungsanleitung

TP-Link

TP-Link AP9650 V1 Bedienungsanleitung

Draytek

Draytek VIGORAP 902 Bedienungsanleitung

EnGenius

EnGenius EAP350 Bedienungsanleitung

Ubiquiti airFiber AF-24-US Bedienungsanleitung

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken