Ubiquiti UAP-PRO Bedienungsanleitung
802.11n PRO Access Point
Model: UAP-PRO
Introduction
Thank you for purchasing the Ubiquiti Networks® UniFi®AP
PRO. This Quick Start Guide is designed to guide you through
installation and also includes warranty terms.
Package Contents
UniFi AP-PRO Mounting Bracket Ceiling Backing Plate
Flat Head Screws
(M3x50, Qty. 3)
Keps Nuts
(M3, Qty. 3)
Screws
(M2.9x20, Qty. 3)
Screw Anchors
(M3x20, Qty. 3)
802.11n PRO Access Point
Model: UAP-PRO
Gigabit PoE (48V, 0.5A)
with Mounting Bracket
Power Cord Quick Start Guide
Installation Requirements
• CAT5/6 cable
• Phillips screwdriver
• Drill and drill bit (6 mm for wall-mounting or 3 mm for
ceiling-mounting)
• Optional: Drywall or keyhole saw (to cut 25 mm hole for
Ethernet cable feed)
TERMS OF USE: All Ethernet cabling runs must use CAT5 (or above). It is the customer’s
responsibility to follow local country regulations, including operation within legal frequency
channels, output power, indoor cabling requirements, and Dynamic Frequency Selection
(DFS) requirements.
System Requirements
• Linux, MacOSX, or Microsoft Windows 7/8
• Java Runtime Environment 1.6 (or above)
• Web Browser: Mozilla Firefox, Google Chrome, or Microsoft
Internet Explorer 8 (or above)
• UniFi Controller software (available at:
downloads.ubnt.com/unifi)
Network Topology Requirements
• A DHCP-enabled network (for the AP to obtain an IP address
as well as for the wireless clients after deployment)
• A management station computer running the UniFi
Controller software, located either onsite and connected to
the same Layer-2 network, or off-site in a cloud or NOC
UAP-Pro
or
NetworkHealth
www WAN LAN
WLAN
VOIP
www WAN LAN WLAN VOIP
IP
DNS
GATEWAY
ACTIVECLIENTS
DOWN
UP
SWITCHES
USERS
GUESTS
DOWN
UP
APS
USERS
GUESTS
DOWN
UP
PHONES
EXTENSION
CALLSIN
CALLSOUT
XXX.XXX.XXX.XXX
XXX.XXX.XXX.XXX 192
0
0
0
0
0
0
162
2
0
0
0
30
4
3
6
0
DASHBOARD
MAP
DEVICES
CLIENTS
CALLS
STATISTICS
INSIGHTS
SETTINGS
CURRENTSITE
Default
REFRESHRATE
2minutes
NetworkHealth
www WAN LAN
WLAN
VOIP
www WAN LAN WLAN VOIP
IP
DNS
GATEWAY
ACTIVECLIENTS
DOWN
UP
SWITCHES
USERS
GUESTS
DOWN
UP
APS
USERS
GUESTS
DOWN
UP
PHONES
EXTENSION
CALLSIN
CALLSOUT
XXX.XXX.XXX.XXX
XXX.XXX.XXX.XXX 192
0
0
0
0
0
0
162
2
0
0
0
30
4
3
6
0
DASHBOARD
MAP
DEVICES
CLIENTS
CALLS
STATISTICS
INSIGHTS
SETTINGS
CURRENTSITE
Default
REFRESHRATE
2minutes
O-Site
Cloud/NOC
On-Site
Management
Station
UniFi Switch
UniFi
Security
Gateway
Internet
LAN
WAN
1G
UAP-AC Outdoor
Sample Network Diagram
All UniFi APs support off-site management controllers.
For setup details, see the User Guide on the website:
documentation.ubnt.com/unifi
Hardware Overview
LED
LED Color Status
White Factory default, waiting to be integrated.
Flashing White Initializing.
Alternating
White/Blue
Device is busy; do not touch or unplug it.
This usually indicates that a process such
as a firmware upgrade is taking place.
Blue
Indicates the device has been successfully
integrated into a network and is working
properly.
Quickly
Flashing Blue
This is used to locate an AP.
When you click Locate in the UniFi
Controller software, the LED on the AP will
flash. It will also flash the location of the AP
on the map three times and then stop.
Steady Blue
with occasional
flashing
Indicates the device is in an isolated state
(all WLANs are brought down until an
uplink is found).
Ports
Main/48V
Ethernet Port
Secondary
Ethernet Port
Reset Button
Cable Feed Plug
Main/48V This Gigabit Ethernet port is used to connect the
power and should be connected to the LAN and DHCP server.
Power can be provided by any of the following:
• Included Gigabit PoE adapter
• 48V, 802.3af compliant switch
• Ubiquiti Networks UniFi Switch
• Ubiquiti Networks TOUGHSwitch™ PRO, model TS-8-PRO
Secondary This Gigabit Ethernet port is used for bridging.
Reset This button serves two functions for the UniFi AP-PRO:
• Restart Press and release the Reset button quickly.
• Restore to Factory Default Settings Press and hold the
Reset button for more then five seconds.
Cable Feed Plug If your Ethernet cable feeds along the
mounting surface, remove theCable Feed Plug.
Locking
Clip
Mounting
Bracket
Locking Clip During installation, the Locking Clip on
the Mounting Bracket locks into the Locking Notch on the
UniFiAP-PRO to help prevent theft.
Hardware Installation
The UniFi AP-PRO can be mounted to the wall or ceiling.
Perform the steps for the appropriate installation:
Wall Mount
1. Position the Mounting Bracket at the desired location on
the wall with the cable feed slot pointed towards the floor.
2. Use a pencil to mark the three holes on the wall. Use a
6mm drill bit to drill the holes.
Optional 25 mm Hole
for Ethernet Cable
Feed through Wall
3. Follow the instruction for your Ethernet cable feed:
-Feeds Through the Wall Cut or drill a circle
approximately 25 mm in diameter, just below the
bottom center of the Mounting Bracket (as shown
above). Then feed the CAT5/6 cable through the hole.
-Feeds Along the Mounting Surface Remove the
Cable Feed Plug on the side of the UniFi AP-PRO.
*640-00207-01*
640-00207-01
4. Insert the Screw Anchors into the 6 mm holes. Secure the
Mounting Bracket to the wall by inserting the Screws into
the anchors.
5. Connect the Ethernet cable to the Main/48V Ethernet port.
6. Align the notch on the UniFi AP-PRO with the notch on the
Mounting Bracket.
7. Turn the UniFi AP-PRO clockwise until it locks into place.
Ceiling Mount
1. Remove the ceiling tile.
2. Place the Mounting Bracket in the center of the ceiling tile.
Mark the three mounting screw holes and 25 mm hole for
the Ethernet cable.
25 mm Hole for
Ethernet Cable Feed
3. Use a 3 mm drill bit to drill the screw holes, and cut or drill
the 25 mm hole for the Ethernet cable feed.
4. Secure the Mounting Bracket to the ceiling tile using the
Ceiling Backing Plate, Flathead Screws, and KepsNuts. Then
feed the Ethernet cable through the 25mmhole.
Andere Handbücher für UAP-PRO
3
Inhaltsverzeichnis
Andere Ubiquiti Drahtloser Zugangspunkt Handbücher
Ubiquiti
Ubiquiti UniFi UAP-AC-PRO Bedienungsanleitung
Ubiquiti
Ubiquiti UF-Nano Bedienungsanleitung
Ubiquiti
Ubiquiti LiteAP ac LAP-120 Bedienungsanleitung
Ubiquiti
Ubiquiti UniFi nanoHD AP Bedienungsanleitung
Ubiquiti
Ubiquiti LAP-GPS Bedienungsanleitung
Ubiquiti
Ubiquiti GigaBeam Bedienungsanleitung
Ubiquiti
Ubiquiti NanoBeam M5-16 Bedienungsanleitung
Ubiquiti
Ubiquiti NanoBeam NBE2ACN Bedienungsanleitung
Ubiquiti
Ubiquiti NanoStation M2 Bedienungsanleitung
Ubiquiti
Ubiquiti UAP-AC-IW Bedienungsanleitung
Ubiquiti
Ubiquiti Rocket2AC Prism Bedienungsanleitung
Ubiquiti
Ubiquiti airFiber AF-11 Bedienungsanleitung
Ubiquiti
Ubiquiti UniFi WiFi BaseStationXG UWB-XG-BK Bedienungsanleitung
Ubiquiti
Ubiquiti UniFi nanoHD AP Bedienungsanleitung
Ubiquiti
Ubiquiti U-Installer Bedienungsanleitung
Ubiquiti
Ubiquiti NanoStation NSM2 Bedienungsanleitung
Ubiquiti
Ubiquiti NanoStation NSM365 Bedienungsanleitung
Ubiquiti
Ubiquiti NanoStation M2 Bedienungsanleitung
Ubiquiti
Ubiquiti UAP Bedienungsanleitung
Ubiquiti
Ubiquiti UniFi Bedienungsanleitung
Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken
D-Link
D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung
Cisco
Cisco Aironet 1550 Series Bedienungsanleitung
Aruba
Aruba IAP-335 Bedienungsanleitung
Advantek Networks
Advantek Networks AWN-AP-54MR Bedienungsanleitung
IP-COM
IP-COM AP355 Bedienungsanleitung
Buffalo
Buffalo AirStation WLA-L11G Bedienungsanleitung
