Ubiquiti IsoStation AC Bedienungsanleitung

ShieldedairMAX ®acRadio

withIsolationAntenna

Model:IS-5AC

Introduction

Thank you for purchasing the Ubiquiti Networks®

IsoStation™AC. This Quick Start Guide is designed to guide you

through installation and also includes warrantyterms.

Package Contents

IsoStation AC Metal Strap

ShieldedairMAX®ac Radio

withIsolation Antenna

Model:IS-5AC

Gigabit PoE (24V, 0.5A)

with Mounting Bracket

Power Cord Quick Start

Guide

cable and earth grounding must be used as conditions of product warranty. TOUGHCable™is

designed for outdoor installations. It is the professional installer’s responsibility to follow local

country regulations, including operation within legal frequency channels, output power, and

Dynamic Frequency Selection (DFS) requirements.

Installation Requirements

• The IS-5AC comes with a default horn, the Horn-5-45.

However, the IS-5AC can also be used with one of the

following antennas (not included):

• Horn-5-30

• Horn-5-60

• Horn-5-90

• U-OMT-Dish

• 7 mm socket wrench or screwdriver

• Shielded Category 5 (or above) cabling with drain wire

should be used for all wired Ethernet connections and

should be grounded through the AC ground of the PoE.

We recommend that you protect your networks from

harmful outdoor environments and destructive ESD events

with industrial-grade, shielded Ethernet cable from Ubiquiti

Networks. For more details, visit

www.ubnt.com/toughcable

• Surge protection should be used for all outdoor installations.

We recommend that you use two Ethernet Surge Protectors,

model ETH-SP, one near the IsoStation and the other at the

entry point to the building. The ETH-SP will absorb power

surges and safely discharge them into the ground.

To LAN

ETH-SP

ES-8-150W

IS-5AC

Hardware Overview

Reset

Button

Ethernet

Port

Power

LED

Power LED The LED will light blue when the device is

connected to a power source.

Ethernet Port This Gigabit Ethernet port is used to connect

the power and should be connected to the LAN and DHCP

server.

Reset Button To reset to factory defaults, press and hold the

Reset button for more than 10 seconds while the IsoStation

is poweredon. Alternatively, the IsoStation may be reset

remotely via a Reset button located on the bottom of the

Gigabit PoE Adapter.

Release Button The default horn antenna (beamwidth: 45°)

can be swapped out for an optional horn with a different

beamwidth. To remove the attached horn antenna, rotate the

horn antenna counterclockwise while depressing the Release

Button.

Release

Button

Hardware Installation

These instructions show the default horn antenna

(beamwidth:45°); however, the IsoStation is also compatible

with the following antennas:

• Horn-5-30

• Horn-5-60

• Horn-5-90

• U-OMT-Dish (refer to the U-OMT-Dish Quick Start Guide

for installation instructions)

1. To install the horn antenna, insert the horn antenna into

the IsoStation and align the arrow on the horn antenna

with the Release Button.

2. Press down on the horn antenna and rotate it clockwise

until you hear a click.

*640-00267-09*

640-00267-09

Pole-Mounting

The IsoStation was designed for quick mounting on a pole.

1. Open the Metal Strap and feed it through the base of the

IsoStation.

2. Wrap the Metal Strap around the pole. Use a 7 mm socket

wrench to turn the screw clockwise and securely fasten the

clamp to the pole.

Connecting Power

1. Remove the port cover by pressing down the center of the

cover and sliding the cover out.

2. Remove the rubber gasket from the port cover.

3. Connect an Ethernet cable to the Ethernet port.

4. Replace the port cover.

5. Fit the rubber gasket over the Ethernet cable, and then

slide the gasket into the port cover.

6. Connect the power using one of the following options:

• Using the included Gigabit PoE Adapter: Go to

Connecting to the PoE Adapter.

• Using a separate PoE switch: Connect the Ethernet

cable from the IsoStation’s Ethernet port to a

PoE-enabled Ethernet port on the switch.

WARNING: The switch port must comply with the

power specifications listed in the Specifications

section of this Quick Start Guide.

Connecting to the PoE Adapter

1. Connect the Ethernet cable from the device to the POE

port on the PoEAdapter.

2. Connect an Ethernet cable from your LAN to the LAN port

on the PoE Adapter.

3. Connect the Power Cord to the PoE Adapter, and then plug

the Power Cord into a power outlet.

Mounting the PoE Adapter (Optional)

1. Remove the PoE Mounting Bracket from the adapter, place

the bracket at the desired location, and mark the two holes.

2. Pre-drill the holes if necessary, and secure the bracket

using two fasteners (not included).

3. Align the adapter’s slots with the tabs of the PoE Mounting

Bracket, and then slide the adapterdown.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Ubiquiti Drahtloser Zugangspunkt Handbücher

Ubiquiti

Ubiquiti UniFi Enterprise AP Bedienungsanleitung

Ubiquiti

Ubiquiti UAP-PRO Bedienungsanleitung

Ubiquiti

Ubiquiti UAP-AC-PRO Bedienungsanleitung

Ubiquiti

Ubiquiti PowerBeam AC GENZ Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi UAP-nanoHD Bedienungsanleitung

Ubiquiti

Ubiquiti Rocket5AC R5AC-PTP Bedienungsanleitung

Ubiquiti

Ubiquiti UAP-AC-PRO Bedienungsanleitung

Ubiquiti

Ubiquiti NBE-5AC-Gen2 Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi UAP-IW-HD Bedienungsanleitung

Ubiquiti

Ubiquiti Rocket M3 Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi UAP-AC-LITE Bedienungsanleitung

Ubiquiti

Ubiquiti LiteBeam LBE-5AC-LR Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi UAP Bedienungsanleitung

Ubiquiti

Ubiquiti UAP-AC-IW Bedienungsanleitung

Ubiquiti

Ubiquiti airFiber AF-5 Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi UAP-FlexHD Bedienungsanleitung

Ubiquiti

Ubiquiti NBE-5AC-Gen2 Bedienungsanleitung

Ubiquiti

Ubiquiti Rocket Prism AC GEN 2 RP-5AC-Gen2 Bedienungsanleitung

Ubiquiti

Ubiquiti UAP-AC-HD Bedienungsanleitung

Ubiquiti

Ubiquiti LiteAP ac LAP-120 Bedienungsanleitung

Ubiquiti

Ubiquiti NBE--2AC--13 Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi UAP-AC-LR Bedienungsanleitung

Ubiquiti

Ubiquiti NanoBridge M5 Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi Bedienungsanleitung

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung

Cisco

Cisco Aironet 1550 Series Bedienungsanleitung

Aruba

Aruba IAP-335 Bedienungsanleitung

Advantek Networks

Advantek Networks AWN-AP-54MR Bedienungsanleitung

IP-COM

IP-COM AP355 Bedienungsanleitung

Buffalo

Buffalo AirStation WLA-L11G Bedienungsanleitung

EnGenius

EnGenius EnStationACv2 Bedienungsanleitung

D-Link

D-Link DAP-3662 Bedienungsanleitung

xG Technology

xG Technology xMax CN1300 Bedienungsanleitung

Widelink

Widelink ezWave WAP-1100 Series Bedienungsanleitung

Edimax

Edimax CAP1200 Bedienungsanleitung

Aruba

Aruba AP-203R Bedienungsanleitung

LuXout Shades

LuXout Shades LUXSHADE MOTION Bedienungsanleitung

CreatComm

CreatComm TB5F Bedienungsanleitung

SineDigital

SineDigital MW-1500AP(H) Bedienungsanleitung

TP-Link

TP-Link AP9650 V1 Bedienungsanleitung

Draytek

Draytek VIGORAP 902 Bedienungsanleitung

EnGenius

EnGenius EAP350 Bedienungsanleitung