Ubiquiti Rocket Prism AC GEN 2 RP-5AC-Gen2 Bedienungsanleitung

5 GHz airMAX®ac Radio

BaseStation with airPrism®

Active RF Filtering Technology

Model: RP-5AC-Gen2

Introduction

Thank you for purchasing the Ubiquiti Networks® Rocket® Prism

RP-5AC-Gen2. This Quick Start Guide is designed to guide you

through installation and also includes warranty terms.

Package Contents

Rocket Prism 5AC GPS Antenna

5GHz airMAX®ac Radio

BaseStationwith airPrism®

ActiveRF Filtering Technology

Model:RP-5AC-Gen2

Gigabit PoE (24V, 1A)

with Mounting Bracket

Power Cord Quick Start Guide

Installation Requirements

• The GPS Antenna needs to have clear line of sight to thesky

for proper GPS operation.

• Shielded Category 5 (or above) cabling should be used for

all wired Ethernet connections and should be grounded

through the AC ground of the PoE.

We recommend that you protect your networks from

harmful outdoor environments and destructive ESD events

with industrial-grade, shielded Ethernet cable from Ubiquiti

Networks. For more details, visit

www.ubnt.com/toughcable

cable and earth grounding must be used as conditions of product warranty. TOUGHCable™is

designed for outdoor installations. It is the customer’s responsibility to follow local country

regulations, including operation within legal frequency channels, output power, and Dynamic

Frequency Selection (DFS) requirements.

Hardware Overview

GPS

Antenna

Connector

RP-SMA

Antenna

Connector:

Chain 1

RP-SMA

Antenna

Connector:

Chain 0

LED Panel

Port Cover

LED Panel

Signal In airOS®, you can modify the wireless

signal strength threshold values for each LED on

the Wireless tab under Signal LED Thresholds. The

default values are shown below:

LED will light blue when the wireless

signal strength is above -65 dBm.

LED will light blue when the wireless

signal strength is above -73 dBm.

LED will light blue when the wireless

signal strength is above -80 dBm.

LED will light blue when the wireless

signal strength is above -94 dBm.

GPS GPS The GPS LED will light steady blue when the

GPS signal strength is sufficient. This requires a

minimum of three satellite connections.

LAN LAN The LAN LED will light steady blue when an

active Ethernet connection is made to the LAN

port and flash when there is activity.

Power The Power LED will light blue when the

device is connected to a power source.

Ports

LAN Port

Reset

Button

Reset Button To reset to factory defaults, press and hold

the Reset button for more than 10 seconds while the Rocket

Prism is poweredon. Alternatively, the Rocket Prism may be

reset remotely via a Reset button located on the bottom of the

Gigabit PoE adapter.

LAN The Gigabit Ethernet port is used to connect the power

and should be connected to the LAN.

Hardware Installation

The Rocket Prism is designed to mount directly onto a Ubiquiti

airMAX RocketDish™antenna for Point-to-Point use or an

airMAX Sector antenna for Point-to-MultiPoint use.

1. Lift the release latch on the bottom of the Rocket Prism

and slide the Port Cover off.

2. Connect an Ethernet cable to the LAN port.

3. Replace the Port Cover.

4. Connect the RF cables to the RP-SMA Antenna Connectors

located on top of the Rocket Prism.

5. Attach the Rocket Prism to the antenna.

a. Align the mounting tabs on the back of the Rocket

Prism with the mounting slots on the antenna.

b. Slide the Rocket Prism down until it locks into place.

CHAIN1 GPS CHAIN0

Mounting on a RocketDish Mounting on a Sector Antenna

6. Attach the other end of the RF cables to the RF connectors

on the antenna.

CHAIN1 GPS CHAIN0

Connecting to a RocketDish Connecting to a Sector Antenna

7. Connect the GPS Antenna to the GPS Antenna Connector on

the Rocket Prism.

CHAIN1 GPS CHAIN0

CHAIN1 GPS CHAIN 0

Connecting the GPS Antenna Connecting the GPS Antenna

8. Attach the protective shroud.

CHAIN1 GPS CHAIN0

Align the hash mark on the top

of the shroud with the notch on

the RocketDish. Rotate the shroud

clockwise until it locks into place.

Slide the protective shroud

down over the Rocket Prism

until it locks into place on the

Sector antenna.

9. Place the GPS Antenna on the mounting hardware.

CHAIN1 GPS CHAIN0

Placement on a Dish Antenna Placement on a Sector Antenna

Connect the power using one of the following options:

• Using the included Gigabit PoE Adapter: Go to “Connecting to

the PoE Adapter”.

• Using a separate PoE switch: Connect the Ethernet cable

from the Rocket Prism’s Ethernet port to a PoE-enabled

Ethernet port on the switch.

WARNING: The switch port must comply with the

power specifications listed in the Specifications

section of this Quick Start Guide.

Connecting to the PoE Adapter

1. Connect the Ethernet cable from the Rocket Prism’s LAN

port to the adapter’s POE port.

2. Connect an Ethernet cable from your LAN to the adapter’s

LAN port.

3. Connect the Power Cord to the adapter’s power port.

Connect the other end of the Power Cord to a power outlet.

Mounting the PoE Adapter (Optional)

1. Remove the PoE Mounting Bracket from the adapter, place

the bracket at the desired location, and mark the two holes.

2. Pre-drill the holes if necessary, and secure the bracket

using two fasteners (not included).

3. Align the adapter’s slots with the tabs of the PoE Mounting

Bracket, and then slide the adapterdown.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Ubiquiti Drahtloser Zugangspunkt Handbücher

Ubiquiti

Ubiquiti NanoBeam NBE2ACN Bedienungsanleitung

Ubiquiti

Ubiquiti LiteBeam LBE-5AC-LR Bedienungsanleitung

Ubiquiti

Ubiquiti IsoStation AC Bedienungsanleitung

Ubiquiti

Ubiquiti UAP-Outdoor-5 Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi nanoHD Bedienungsanleitung

Ubiquiti

Ubiquiti Loco5AC Bedienungsanleitung

Ubiquiti

Ubiquiti airFiber AF-11 Bedienungsanleitung

Ubiquiti

Ubiquiti PBE-M5-400 Bedienungsanleitung

Ubiquiti

Ubiquiti NBE-5AC-Gen2 Bedienungsanleitung

Ubiquiti

Ubiquiti LiteBeam M5 LBE-M5-23 Bedienungsanleitung

Ubiquiti

Ubiquiti Bullet AC-IP67 Bedienungsanleitung

Ubiquiti

Ubiquiti UAP-PRO Bedienungsanleitung

Ubiquiti

Ubiquiti airFiber AF 60 Bedienungsanleitung

Ubiquiti

Ubiquiti PowerBeam AC GENZ Bedienungsanleitung

Ubiquiti

Ubiquiti PBE-M5-300-US Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi Dream Machine Beacon Bedienungsanleitung

Ubiquiti

Ubiquiti NBE-M5-16 Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi USW-Flex-Mini Bedienungsanleitung

Ubiquiti

Ubiquiti PowerBeam AC PBE-5AC-300 Bedienungsanleitung

Ubiquiti

Ubiquiti M5 GPS Rocket M Series Bedienungsanleitung

Ubiquiti

Ubiquiti LiteBeam LBE-5AC-LR Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation 5AC Loco Bedienungsanleitung

Ubiquiti

Ubiquiti GigaBeam GBE Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi AC AP Mesh Pro Bedienungsanleitung

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung

Cisco

Cisco Aironet 1550 Series Bedienungsanleitung

Aruba

Aruba IAP-335 Bedienungsanleitung

Advantek Networks

Advantek Networks AWN-AP-54MR Bedienungsanleitung

IP-COM

IP-COM AP355 Bedienungsanleitung

Buffalo

Buffalo AirStation WLA-L11G Bedienungsanleitung

EnGenius

EnGenius EnStationACv2 Bedienungsanleitung

D-Link

D-Link DAP-3662 Bedienungsanleitung

Widelink

Widelink ezWave WAP-1100 Series Bedienungsanleitung

Edimax

Edimax CAP1200 Bedienungsanleitung

xG Technology

xG Technology xMax CN1300 Bedienungsanleitung

Aruba

Aruba AP-203R Bedienungsanleitung

LuXout Shades

LuXout Shades LUXSHADE MOTION Bedienungsanleitung

CreatComm

CreatComm TB5F Bedienungsanleitung

SineDigital

SineDigital MW-1500AP(H) Bedienungsanleitung

TP-Link

TP-Link AP9650 V1 Bedienungsanleitung

Draytek

Draytek VIGORAP 902 Bedienungsanleitung

EnGenius

EnGenius EAP350 Bedienungsanleitung