Ubiquiti NanoBeam NBE2ACN Bedienungsanleitung

2.4 GHz airMAX®ac CPE with

Dedicated Wi-Fi Management

Model: NBE-2AC-13

Introduction

Thank you for purchasing the Ubiquiti Networks®

NanoBeam®AC. This Quick Start Guide is designed to guide

you through installation and also includes warrantyterms.

Package Contents

NanoBeam Ball Joint

Mount

Lock Ring

2.4GHz airMAX®ac CPE with

DedicatedWi-Fi Management

Model:NBE-2AC-13

Metal Strap Gigabit PoE (24V, 0.5A)

with Mounting Bracket

Power Cord Quick Start

Guide

cable and earth grounding must be used as conditions of product warranty. TOUGHCable™is

designed for outdoor installations. It is the professional installer’s responsibility to follow local

country regulations, including operation within legal frequency channels, output power, and

Dynamic Frequency Selection (DFS) requirements.

Installation Requirements

The NanoBeam can be mounted on a pole or to a wall. A Metal

Strap (included) is used for pole-mounting. For wall-mounting,

a suitable fastener such as a screw or bolt (not included) is

required.

• Pole-mounting: 7 mm socket wrench or screwdriver

• Wall-mounting: wall fastener (not included)

• Shielded Category 5 (or above) cabling with drain wire

should be used for all wired Ethernet connections and

should be grounded through the AC ground of the PoE.

We recommend that you protect your networks from

harmful outdoor environments and destructive ESD events

with industrial-grade, shielded Ethernet cable from Ubiquiti

Networks.

For more details, visit www.ubnt.com/toughcable

• Surge protection should be used for all outdoor installations.

We recommend that you use two Ethernet Surge Protectors,

model ETH-SP, one near the NanoBeam and the other at the

entry point to the building. The ETH-SP will absorb power

surges and safely discharge them into the ground.

To LAN

ETH-SP

ES-8-150W

NBE-2AC-13

Hardware Overview

M/N:NBE-2AC -13

24V 0.5A GigE PoE

This devic e complies with P art 15 of FCC rules.

Operation is s ubject to the followin g 2 conditions:

1) this device may no t cause harmful inte rference and,

2) this device m ust accept any inter ference received ,

including interference that may cause undesired

operation.

Compliant

RoHS

FCC ID:SWX-NBE2ACN IC: 6545A-NBE2ACN

PolarityAlign

2.4GHz

LEDs

Reset Button Ethernet Port

(10/100/1000 Mbps)

Reset Button To reset to factory defaults, press and hold the

Reset button for more than 10 seconds while the NanoBeam

is already poweredon. Alternatively, the NanoBeam may be

reset remotely via a Reset button located on the bottom of the

Gigabit PoE Adapter.

Ethernet Port This Gigabit Ethernet port is used to connect

the power and should be connected to the LAN and DHCP

server. Power can be provided by any of the following:

• Gigabit PoE adapter (included)

• Ubiquiti Networks EdgeSwitch®

• Ubiquiti Networks EdgeRouter™ PoE

LEDs

Power The Power LED will light blue when the

device is connected to a power source.

Ethernet The Ethernet LED will light steady blue

when an active Ethernet connection is made and

flash when there is activity.

Signal In airOS®, you can modify the threshold

value for the wireless signal strength LEDs on the

Wireless tab under Signal LED Thresholds. Each LED

will light when the wireless signal strength is equal

to or greater than the LED’s threshold value. The

default threshold values for these LEDs are shown

below:

-94 dBm -80 dBm -73 dBm -65 dBm

Hardware Installation

The NanoBeam can be mounted on a pole or to a wall. Perform

the steps for the appropriate installation:

Note: The NanoBeam can also be mounted inside a

window using the NanoBeam Window Mount, model

NBE-19-WM (sold separately). For instructions, see the

NanoBeam Window Mount Quick Start Guide.

Pole-Mount

1. Insert the Ball Joint Mount into the Lock Ring with the

threads of the Lock Ring facing the ball joint.

2. Open the Metal Strap and feed it through the base of the

Ball Joint Mount.

3. Wrap the Metal Strap around the pole. Use a 7 mm socket

wrench to turn the screw clockwise and securely fasten the

clamp to the pole.

4. Attach the NanoBeam to the Ball Joint Mount and turn the

Lock Ring to secure it. Keep the Lock Ring loose enough to

allow the NanoBeam to pivot for aiming.

Wall-Mount

The NanoBeam must be mounted directly to a wood stud

or other structurally stable surface to avoid damage to the

mounting hole when you adjust the aim.

Optional Accessory

To enhance stability, you can use the NanoBeam Wall Mount

Kit, model NBE-WMK (soldseparately).

Note: Center screw included. Two optional screws (not

included) provide additional stability.

Installation Instructions

1. Mark the desired location of the mounting point.

2. If needed, drill a pilot hole for the fastener (not included).

3. Insert the Ball Joint Mount into the Lock Ring with the

threads of the Lock Ring facing the ball joint.

4. If you are using the optional NanoBeam Wall Mount Kit,

then skip to step b.

a. To attach the Ball Joint Mount to the wall, insert a

fastener (not included) through the center of the ball

joint, and into the wall. Securely tighten the fastener.

Proceed to step 5.

b. To attach the Ball Joint Mount to the wall, insert the Wall

Mount Kit screw through the center of the ball joint,

through the Wall Mount Kit plate, and into the wall.

Securely tighten the screw.

5. Attach the NanoBeam to the Ball Joint Mount and turn the

Lock Ring to secure it. Keep the Lock Ring loose enough to

allow the NanoBeam to pivot for aiming.

Aiming

1. Ensure the opening of the Ethernet cable is pointed

towards the ground.

2. Aim the front of the NanoBeam towards the other end of

the wireless link.

3. Hand-tighten the Lock Ring to lock the aim.

Note: Do not use a tool to tighten the Lock Ring.

Tighten the Lock Ring by hand only.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Ubiquiti Drahtloser Zugangspunkt Handbücher

Ubiquiti

Ubiquiti NanoBeam 5AC Gen2 Bedienungsanleitung

Ubiquiti

Ubiquiti UF-Nano Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi USW-Flex-Mini Bedienungsanleitung

Ubiquiti

Ubiquiti U-LTE Bedienungsanleitung

Ubiquiti

Ubiquiti AG-PRO-INS Bedienungsanleitung

Ubiquiti

Ubiquiti Uni-fi AP Bedienungsanleitung

Ubiquiti

Ubiquiti NanoBridge M5 Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi nanoHD AP Bedienungsanleitung

Ubiquiti

Ubiquiti PBE-M5-620 Bedienungsanleitung

Ubiquiti

Ubiquiti BulletM2-HP Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi nanoHD UAP-nanoHD Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi UAP-AC-LR-5-EU Bedienungsanleitung

Ubiquiti

Ubiquiti UniFI UAP-AC Bedienungsanleitung

Ubiquiti

Ubiquiti Loco5AC Bedienungsanleitung

Ubiquiti

Ubiquiti IsoStation AC Bedienungsanleitung

Ubiquiti

Ubiquiti airFiber AF 60 Bedienungsanleitung

Ubiquiti

Ubiquiti nano station M Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi UAP--AC--HD Bedienungsanleitung

Ubiquiti

Ubiquiti UAP-PRO Bedienungsanleitung

Ubiquiti

Ubiquiti LTU-Lite Bedienungsanleitung

Ubiquiti

Ubiquiti UAP-PRO Bedienungsanleitung

Ubiquiti

Ubiquiti NBE-M5-16 Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi AP AC SHD Bedienungsanleitung

Ubiquiti

Ubiquiti NBE-5AC-Gen2 Bedienungsanleitung

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung

Cisco

Cisco Aironet 1550 Series Bedienungsanleitung

Aruba

Aruba IAP-335 Bedienungsanleitung

Advantek Networks

Advantek Networks AWN-AP-54MR Bedienungsanleitung

IP-COM

IP-COM AP355 Bedienungsanleitung

Buffalo

Buffalo AirStation WLA-L11G Bedienungsanleitung

EnGenius

EnGenius EnStationACv2 Bedienungsanleitung

D-Link

D-Link DAP-3662 Bedienungsanleitung

Widelink

Widelink ezWave WAP-1100 Series Bedienungsanleitung

Edimax

Edimax CAP1200 Bedienungsanleitung

xG Technology

xG Technology xMax CN1300 Bedienungsanleitung

Aruba

Aruba AP-203R Bedienungsanleitung

LuXout Shades

LuXout Shades LUXSHADE MOTION Bedienungsanleitung

CreatComm

CreatComm TB5F Bedienungsanleitung

SineDigital

SineDigital MW-1500AP(H) Bedienungsanleitung

TP-Link

TP-Link AP9650 V1 Bedienungsanleitung

Draytek

Draytek VIGORAP 902 Bedienungsanleitung

EnGenius

EnGenius EAP350 Bedienungsanleitung