Ubiquiti UniFI UAP-AC Bedienungsanleitung

Enterprise WiFi System

Model: UAP-AC

Introduction

Thank you for purchasing the Ubiquiti Networks® UniFi®

Enterprise WiFi System. This system includes the UniFi

Controller software, which allows you to manage your wireless

network using a web browser. The software and User Guide

are available for download at: downloads.ubnt.com/unifi

This Quick Start Guide includes the warranty terms and is for

use with the UniFi AP-AC, model UAP-AC.

Package Contents

UniFi AP AC Mounting Bracket Ceiling Backing Plate

Flat Head Screws

(M3x50, Qty. 4)

Keps Nuts

(M3, Qty. 4)

Screws

(M2.9x20, Qty. 4)

Screw Anchors

(M3x20, Qty. 4)

Enterprise WiFi System

Model: UAP-AC

Gigabit PoE Adapter

(48V, 0.5A Gigabit)

Power Cord Quick Start Guide

Installation Requirements

• CAT5/6 cable

• Phillips screwdriver

• Drill and drill bit (6 mm for wall-mounting or 3 mm for

ceiling-mounting)

• Optional: Drywall or keyhole saw (to cut 25 mm hole for

Ethernet cable feed)

responsibility to follow local country regulations, including operation within legal frequency

channels, output power, indoor cabling requirements, and Dynamic Frequency Selection

(DFS) requirements.

System Requirements

• Microsoft Windows 7/8, MacOSX, or Linux

• Java Runtime Environment 1.6 (or above)

• Web Browser: Mozilla Firefox, Google Chrome, or Microsoft

Internet Explorer 8 (or above)

Network Topology Requirements

• A DHCP-enabled network (for the AP to obtain an IP address

as well as for the wireless clients after deployment)

• A management station running the UniFi Controller

software, located either on-site and connected to the same

Layer-2 network, or off-site in a cloud or NOC

UniFi Switch

UniFi

Security

Gateway

Internet

O-Site

Cloud/NOC

On-Site

Management

Station

UAP-AC UAP-PRO

UAP-Outdoor

LAN

WAN

Sample Network Diagram

All UniFi devices support off-site management controllers.

For setup details, see the User Guide on the website:

documentation.ubnt.com/unifi

Hardware Overview

LED

LED Color Status

White Factory default, waiting to be integrated.

Flashing White Initializing.

Alternating

White/Blue

Device is busy; do not touch or unplug it.

This usually indicates that a process such

as a firmware upgrade is taking place.

Blue

Indicates the device has been successfully

integrated into a network and is working

properly.

Quickly

Flashing Blue

This is used to locate an AP.

When you click Locate in the UniFi

Controller software, the AP will flash. It

will also display the location of the AP on

the map.

Steady Blue

with occasional

flashing

Indicates the device is in an isolated state

(all WLANs are brought down until an

uplink is found).

Ports

MAIN SECONDARY

Reset

Main Port Secondary Port

Reset Button

Cable Feed Plug

Locking

Notch

Locking

Clip

Mounting Bracket

Main The Main port is a Gigabit Ethernet port used to connect

the power and should be connected to the LAN and DHCP

server. Power can be provided by any of the following:

• Gigabit PoE Adapter (included)

• PoE+ 802.3at compliant switch

• Ubiquiti Networks UniFi Switch

Secondary The Secondary port is a Gigabit Ethernet port used

for bridging.

Reset The Reset button serves two functions for the UniFi AP:

• Restart Press and release the Reset button quickly.

• Restore to Factory Default Settings Press and hold the

Reset button for more then five seconds.

Locking Clip During installation, the Locking Clip on the

Mounting Bracket locks into the Locking Notch on the UniFi AP

to help prevent theft.

Cable Feed Plug If your Ethernet cable feeds along the

mounting surface, remove the Cable Feed Plug.

Hardware Installation

The UniFi AP can be mounted on the wall or ceiling. Perform

the steps for the appropriate installation:

Wall Mount

1. Position the Mounting Bracket at the desired location on

the wall with the cable feed slot pointed towards the floor.

2. Use a pencil to mark the four mounting holes. Use a 6 mm

drill bit to drill the mounting holes.

Top

Optional 25 mm Hole for

Ethernet Cable Feed through Wall

3. Follow the instruction for your type of Ethernet cable feed:

- Feeds Through the Wall Cut or drill a circle

approximately 25 mm in diameter, just below the

bottom center of the Mounting Bracket (as shown

above). Then feed the CAT5/6 cable through the hole.

- Feeds Along the Mounting Surface Remove the

Cable Feed Plug on the side of the UniFi AP.

*640-00076-04*

640-00076-04

4. Insert the Screw Anchors into the 6 mm holes. Secure the

Mounting Bracket to the wall by inserting the Screws into

the anchors.

5. Connect the Ethernet cable to the Main port. If the feed is

along the mounting surface, feed the cable through the

Cable Feed of the UniFi AP.

MAIN SECONDARY

RESET

6. Align the slots on the UniFi AP with the tabs on the

Mounting Bracket.

7. Slide the UniFi AP down until it locks into place.

Ceiling Mount

1. Remove the ceiling tile.

2. Place the Ceiling Backing Plate in the center of the ceiling

tile. Mark the four mounting screw holes and 25 mm hole

for the Ethernet cable feed.

25 mm Hole for Ethernet Cable Feed

3. Use a 3 mm drill bit to drill the screw holes, and cut or drill

the hole for the Ethernet cable feed.

4. Secure the Mounting Bracket to the ceiling tile using the

Ceiling Backing Plate, Flat Head Screws, and Keps Nuts. Then

feed the Ethernet cable through the 25mmhole.

Andere Handbücher für UniFI UAP-AC

Inhaltsverzeichnis

Andere Ubiquiti Drahtloser Zugangspunkt Handbücher

Ubiquiti

Ubiquiti UniFi Stadium XG Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi AP-AC PRO Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi UAP-FlexHD Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation NSM365 Bedienungsanleitung

Ubiquiti

Ubiquiti AirMax AC Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi nanoHD AP Bedienungsanleitung

Ubiquiti

Ubiquiti AF-2X Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi Switch Flex Bedienungsanleitung

Ubiquiti

Ubiquiti Rocket 5AC-Lite Bedienungsanleitung

Ubiquiti

Ubiquiti IS-5AC Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi AP FlexHD Bedienungsanleitung

Ubiquiti

Ubiquiti IsoStation M5 Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi UAP-nanoHD Bedienungsanleitung

Ubiquiti

Ubiquiti AF-2X Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi UAP-IW-HD Bedienungsanleitung

Ubiquiti

Ubiquiti PBE-M5-400 Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation 5AC Loco Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation AC Bedienungsanleitung

Ubiquiti

Ubiquiti Uni-fi AP Bedienungsanleitung

Ubiquiti

Ubiquiti NB?2G18 Bedienungsanleitung

Ubiquiti

Ubiquiti RP5AC-PRISM Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi Enterprise AP Bedienungsanleitung

Ubiquiti

Ubiquiti UAP Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi AP BeaconHD Bedienungsanleitung

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung

Cisco

Cisco Aironet 1550 Series Bedienungsanleitung

Aruba

Aruba IAP-335 Bedienungsanleitung

Advantek Networks

Advantek Networks AWN-AP-54MR Bedienungsanleitung

IP-COM

IP-COM AP355 Bedienungsanleitung

Buffalo

Buffalo AirStation WLA-L11G Bedienungsanleitung

EnGenius

EnGenius EnStationACv2 Bedienungsanleitung

D-Link

D-Link DAP-3662 Bedienungsanleitung

Widelink

Widelink ezWave WAP-1100 Series Bedienungsanleitung

Edimax

Edimax CAP1200 Bedienungsanleitung

xG Technology

xG Technology xMax CN1300 Bedienungsanleitung

Aruba

Aruba AP-203R Bedienungsanleitung

LuXout Shades

LuXout Shades LUXSHADE MOTION Bedienungsanleitung

CreatComm

CreatComm TB5F Bedienungsanleitung

SineDigital

SineDigital MW-1500AP(H) Bedienungsanleitung

TP-Link

TP-Link AP9650 V1 Bedienungsanleitung

Draytek

Draytek VIGORAP 902 Bedienungsanleitung

EnGenius

EnGenius EAP350 Bedienungsanleitung