Ubiquiti PBE-M5-620 Bedienungsanleitung

High-Performance

Integrated InnerFeed™

airMAX®Bridge

Model: PBE-M5-620

Introduction

Thank you for purchasing the Ubiquiti Networks®

PowerBeam™. This Quick Start Guide is designed to guide you

through installation and also includes warranty terms.

Package Contents

Dish Reflector with

Mounting Bracket

Antenna

Feed

Rear

Housing

Support

Arm

Upper Pole

Bracket Assembly

Lower Pole

Bracket

Brace Screws

(M6, Qty. 4)

Hex Head Bolts

(M8, Qty. 5)

Lock Washers

(M8, Qty. 5)

Flat Washers

(M8, Qty. 5)

Stabilizer Brackets

(Qty. 2)

M10x100 Bolts

(Qty. 2)

Serrated Flange Nuts

(M10, Qty. 2)

High-Performance

Integrated InnerFeed™

airMAX®Bridge

Model: PBE-M5-620

M8x150 Carriage

Bolts (Qty. 4)

Pole Clamps

(Qty. 2)

Gigabit PoE

Adapter with

Mounting Bracket

Power

Cord

Quick Start

Guide

cable and earth grounding must be used as conditions of product warranty. TOUGHCable™

is designed for outdoor installations. It is the customer’s responsibility to follow local country

regulations, including operation within legal frequency channels, output power, and Dynamic

Frequency Selection (DFS) requirements.

Hardware Overview

Bottom View

Cable Door

Rear Housing

Technology

Ethernet Port

Release

Button Slot

Release Button

Dish

Reflector

Alignment Pins

Reset Button

Antenna Feed

Mounting Bracket

Reset Button To reset to factory defaults, press and hold the

Reset button for more than 10 seconds while the PowerBeam

is already poweredon. Alternatively, the PowerBeam may be

reset remotely via a Reset button located on the bottom of the

Gigabit PoE Adapter.

Release Button After you assemble the PowerBeam, check

the Release button; it should be fully engaged in the Release

Button Slot of the Rear Housing. This ensures that the Antenna

Feed is locked into place. If you need to remove the Antenna

Feed, you must depress the Release button first.

LEDs

Signal The default values (from left to right) are

shown below:

LED will light blue when the wireless signal

strength is equal to or above -65 dBm.

LED will light blue when the wireless signal

strength is equal to or above -73 dBm.

LED will light blue when the wireless signal

strength is equal to or above -80 dBm.

LED will light blue when the wireless signal

strength is equal to or above -94 dBm.

Ethernet The Ethernet LED will light steady blue

when an active Ethernet connection is made and

flash when there is activity.

Power The Power LED will light blue when the

device is connected to a power source.

Application Examples

The PowerBeam mounted

outdoors with the Dish

Reflector installed provides

directional outdoor coverage.

(The gain depends on the

reflector.)

The PowerBeam mounted

outdoors without the Dish

Reflector installed provides

outdoor-to-indoor coverage

using the 3 dBi Antenna

Feedonly.

Installation Requirements

• Phillips screwdriver

• 13 mm wrench

• 16 mm wrench

• Shielded Category 5 (or above) cabling should be used for

all wired Ethernet connections and should be grounded

through the AC ground of the PoE.

We recommend that you protect your networks from the

most brutal environments and devastating ESD attacks

with industrial-grade shielded Ethernet cable from Ubiquiti

Networks. For more details, visit www.ubnt.com/toughcable

Installation

1. Line up the Alignment Pins of the Rear Housing with the

alignment holes of the Dish Reflector. Insert the pins and

push until they lock intoplace.

2. Push in the sides of the Cable Door and detach it from the

Rear Housing.

3. Attach the Antenna Feed:

a. Insert the Antenna Feed into the Rear Housing, and push

until it locks into place with a click.

b. Lightly pull the Antenna Feed to ensure that it is locked

into place and the Release button is fully engaged.

Release Button

Bottom View

4. Connect the Ethernet cable:

a. Connect an Ethernet cable to the Ethernet Port of the

Antenna Feed.

b. Re-attach the Cable Door to the Rear Housing.

5. Attach two Hex Head Bolts, two Lock Washers, and two Flat

Washers to the bottom of the Mounting Bracket. Ensure that

there is a gap of 8 mm between each Flat Washer and the

Mounting Bracket.

Note: Ensure that each Lock Washer is always

installed between the Hex Head Bolt and Flat Washer.

Flat Washer

Lock Washer

Hex Head Bolt

8 mm

6. Attach the horizontal slot of the Support Arm to the Upper

Pole Bracket using a Hex Head Bolt, Lock Washer, and

FlatWasher.

Note: Ensure that the degree settings are the same

on both arms of the Upper Pole Bracket.

Degree markings

facing outward

7. Attach the Brace to the pole brackets using the four Screws.

8. Each M8x150 Carriage Bolt includes a serrated flange nut.

Remove these and use them in the next step.

9. Attach one Pole Clamp to each pole bracket.

a. Insert two M8x150 Carriage Bolts into each pole bracket.

b. Slide the hole of a Pole Clamp over one bolt of each

pole bracket.

c. Place one serrated flange nut on each bolt.

Andere Handbücher für PBE-M5-620

Inhaltsverzeichnis

Andere Ubiquiti Drahtloser Zugangspunkt Handbücher

Ubiquiti

Ubiquiti UAP-PRO Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi nanoHD Bedienungsanleitung

Ubiquiti

Ubiquiti NBE--2AC--13 Bedienungsanleitung

Ubiquiti

Ubiquiti NanoBeam M5 Bedienungsanleitung

Ubiquiti

Ubiquiti UniFI UAP-AC Bedienungsanleitung

Ubiquiti

Ubiquiti UAP-AC-PRO Bedienungsanleitung

Ubiquiti

Ubiquiti LAP-GPS Bedienungsanleitung

Ubiquiti

Ubiquiti RocketM Bedienungsanleitung

Ubiquiti

Ubiquiti AirOS B2 Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi nanoHD UAP-nanoHD Bedienungsanleitung

Ubiquiti

Ubiquiti PowerBeam PBE-5AC400 Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi Switch Flex Mini Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi UAP-AC-LR Bedienungsanleitung

Ubiquiti

Ubiquiti airFiber AF-11 Bedienungsanleitung

Ubiquiti

Ubiquiti NBE-M5-16 Bedienungsanleitung

Ubiquiti

Ubiquiti AF-2X Bedienungsanleitung

Ubiquiti

Ubiquiti UAP-PRO Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi UAP-IW-HD Bedienungsanleitung

Ubiquiti

Ubiquiti BulletAC-IP67 Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation 5AC Loco Bedienungsanleitung

Ubiquiti

Ubiquiti PowerBeam AC PBE-5AC-300 Bedienungsanleitung

Ubiquiti

Ubiquiti PowerBeam ac ISO Bedienungsanleitung

Ubiquiti

Ubiquiti Loco5AC Bedienungsanleitung

Ubiquiti

Ubiquiti LiteAP ac LAP-120 Bedienungsanleitung

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung

Cisco

Cisco Aironet 1550 Series Bedienungsanleitung

Aruba

Aruba IAP-335 Bedienungsanleitung

Advantek Networks

Advantek Networks AWN-AP-54MR Bedienungsanleitung

IP-COM

IP-COM AP355 Bedienungsanleitung

Buffalo

Buffalo AirStation WLA-L11G Bedienungsanleitung

EnGenius

EnGenius EnStationACv2 Bedienungsanleitung

D-Link

D-Link DAP-3662 Bedienungsanleitung

xG Technology

xG Technology xMax CN1300 Bedienungsanleitung

Widelink

Widelink ezWave WAP-1100 Series Bedienungsanleitung

Edimax

Edimax CAP1200 Bedienungsanleitung

Aruba

Aruba AP-203R Bedienungsanleitung

LuXout Shades

LuXout Shades LUXSHADE MOTION Bedienungsanleitung

CreatComm

CreatComm TB5F Bedienungsanleitung

SineDigital

SineDigital MW-1500AP(H) Bedienungsanleitung

TP-Link

TP-Link AP9650 V1 Bedienungsanleitung

Draytek

Draytek VIGORAP 902 Bedienungsanleitung

EnGenius

EnGenius EAP350 Bedienungsanleitung